Search Documents

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By J. J. Crowder, A. L. Coulson

Ground support is a significant component of underground mining costs. The rehabilitation of failed support, however, is often much more expensive than the initial installation. This paper investigates whether the right type and length of support can be designed correctly the first time, through forward modelling of the support and the mining process. Back analyses demonstrate how high-quality instrumentation and monitoring can help with the estimation of the post-peak (post-failure) rock mass parameters required for a comprehensive analysis. A hybrid modelling approach combines a three-dimensional mine-wide boundary element model with a non-linear finite element model to allow for the failure process in the rock mass. The back analyses demonstrate that, for the case study site, the post-peak Generalized Hoek-Brown value of mr must be reduced significantly in order to properly simulate displacements observed in instrumentation data. High-quality instrumentation data is the key to post-peak rock mass parameter calibration. The procedures outlined in the paper highlight the need for a new hybrid numerical modelling package that can use the influence of three-dimensional mining-induced stresses to predict displacements in, and potential failure of, rock masses surrounding mining infrastructure in order to radically alter strategic and tactical mine design.

Jan 1, 2007

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By A. Musschoot

"The paper will review general types and designs of vibratory feeders, describing briefly the design features and characteristics that apply to the application of specific types. Control considerations for selecting types will be dis• cussed, such as fixed or adjustable, manual or automatic, individual or multiple bank, and process requirements. Design parameters for hopper openings and installation geometry will be discussed, including consideration of material size distribution, segregation, moisture content and other characteristics, based on practical applications and experience as well as theory. Pan designs and the selection of pan materials will also be discussed with reference to wear, corrosion, impact and practical economic factors."

Jan 1, 1972

By C. S. Parsons

Custom milling-plants have been operated successfully for a great many years on this continent. One of the outstanding examples in the United States is the Golden Cycle mill at Colorado Springs, which mills the gold-telluride ores from the Cripple Creek district. In eastern Canada, the Northern Custom Concentrators, Limited, at Cobalt, successfully treated the cobalt-silver ores of that area for a number of years. Flotation plants have entered the custom field in the past few years. The building of flotation concentrators to treat ores on a custom basis indicates the advance which has been made in flotation. In fact, three years ago it was considered almost impossible to treat successfully a mixture of miscellaneous ores by flotation. The methods used at that time were considered so delicate that any change, even in a single ore, would usually result in decreasing the effectiveness of the separation. Today we find four large custom flotation plants in the United States and one in Canada for treating complex lead-zinc ores from many different localities. The advent of these mills was brought about by the serious problem confronting the lead-smelting plants due to increasing amounts of zinc in the ores presented for treatment. It was necessary to penalize the mines shipping high-zinc ores. The penalty is justified, because high zinc in the lead blast-furnace charge not only decreases the tonnage of the furnace but increases the amount of flux necessary, as well as increasing the metal loss in the slag. It has been estimated that in the Salt Lake valley alone, 75,000,000 pounds of zinc was lost in the slag-dumps from the operations of three large lead blast-furnace plants. It has also been estimated that $150,000 worth of additional flux was required to slag this zinc. It was to avoid at least a part of this wste and to help maintain an ore supply that custom flotation concentrators were built by the smelters.

Jan 1, 1928

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By R. W. Wein, L C. Bliss

Northern ecosystems are dominated by a harsh physical environment which dictates a need for biological adaptation. As yet, it is unknown just how these adapted plants and animals will tolerate industrial development. Our work, sponsored by university, government and industry, is part of an effort to evaluate this developmental impact. Our present studies and the results to date will be discussed. Other problems to which the environmental student may address himself in the future to ensure against environ-mental degradation will be suggested.

Jan 1, 1971

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By W. H. Zieman

NORMAN WEISS, Milling Engineer, American Smelting• and Refining Company: The subject of the Forum on Rod and Ball Mill Liners is very fascinating, and there is no end of discussion when operators get together on grinding. However, the hypotheses and suppositions easily outrun the facts, especially when we •consider the inaccuracy of many reported observations. Still surprisingly small is the number of concentrators even reasonably well equipped to measure power consumption of each grinding mill, together with running time, so that data on this tangible factor, at least, can be obtained with precision. While the more elaborate devices of this nature, producing for each 24-hour period the total power consumption, average kilowatt hours per hour, short-term demand chart, instantaneous demand, and print-out, may cost in the neighbourhood of $2,500 per mill and may be difficult to justify, the combination of an ammeter, watthour meter, and running-time meter will cost only a few hundred dollars, so there appears to be little reason not to in-stall them in view of their numerous advantages.

Jan 1, 1959

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

In this study, we develop a detailed model of the likely future carbon footprint of primary copper supply. We develop a peak copper production model, based on a detailed copper resource data set, and combine this with a comprehensive life cycle assessment model of copper mining and milling to predict greenhouse gas emission rates and intensities of Australian and global copper production up to 2100. By establishing a quantitative prediction of both copper production and corresponding greenhouse gas emissions of Australian and global copper industry, we then analysed the emissions intensity of various energy input scenarios, such as business-as-usual, solar thermal electricity and solar thermal electricity with biodiesel. The Australian Government has an aspirational goal for long-term greenhouse gas emissions of an 80% reduction from the 2000 level by 2050. For the copper sector, this means moving from about 12.6 Mt CO2e in 2000 to a goal of some 2.52 Mt CO2e in 2050 (assuming equal emissions reductions across the economy). Based on the energy sources modelled, only the solar thermal plus biodiesel scenario was capable of achieving this goal at about 0.15 Mt CO2e, since the solar thermal alone scenario still includes normal petro-diesel as a major source of emissions. Overall, it is clear that there are abundant resources which can meet expected long-term copper demands, the critical issue is more the carbon (and environmental) footprint of different copper supplies and use rather than how much is available for mining. It is clear that the switch to renewable energy can have a profound impact on the carbon intensity of copper supply, even allowing for increased energy intensity as ore grades decline, and a complete conversion to renewable energy will position the copper sector to meet existing annual greenhouse gas emissions targets and goals.

Aug 1, 2013

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By Jerry Ran

Many large underground mines using the open stoping method have changed their primary applications of consolidated rock fill (CRF) to paste or consolidated hydraulic fill due to considerations of demand in infrastructure and equipment, system reliability, backfill capacity and material sources. However, some smaller or even large mines still use or consider using CRF for backfill purpose due to factors such as capital expenditure, availability or suitability of other fill types or in some cases local regulatory requirements. As demands on CRF applications diminish among major mining companies, there is a lack of recent literature on application of CRF to open stoping in design and operation. There are several methods being used for fill strength design. Results from these methods have been successfully applied to paste or hydraulic fill. However, the design strength for CRF is much higher than that determined by use of these widely accepted methods. In operation, CRF preparation and placement have significant impacts on the quality of placed CRF and therefore the mining performance. This paper reviews the current fill design methods and their applications to open stoping with presentation of the bench marking data, presents fill failure cases and various CRF preparation and placement arrangements and discusses quality assurance and control programs.

Jun 1, 2012

By D. J. W. Piper, T. Hundert, G. Pe-Piper

"Abstract - Potentially commercial deposits of kaolin are found in the fluvial Lower Cretaceous Chaswood Formation, the sedimentologically proximal equivalent of deltaic sediments of the offshore Scotian basin. The geological setting of the kaolin deposits has been interpreted from high-resolution seismic-reflection profiles and boreholes, and mineralogical studies on one reference borehole. The kaolin is a product of early diagenesis involving meteoric water below the water table. The distribution of kaolin is controlled by the presence of intraformational unconformities that were sites of ground water recharge, and are marked by the development of oxisols above the water table. Such diagenesis was facilitated by interbedded, loosely consolidated, permeable sandstone. The highest-grade kaolin deposits are found in areas close to river belts, where overbank muds were not sufficiently drained to develop paleosols, but where later uplift created intraformational unconformities. In the sandstone, meteoric water flow altered feldspars to kaolin, thus yielding commercial silica sand deposits. It also altered ilmenite to rutile, which is concentrated as secondary placers in modern rivers that have eroded the Chaswood Formation and tills derived therefrom. Sommaire - Des dépôts de kaolin potentiellement économiques ont été notés dans la Formation de Chaswood d'’âge Crétacé Inférieur, laquelle constitue un équivalent latéral en milieu fluviatile aux sédiments deltaïques du bassin de Scotian. Le contexte géologique de ces dépôts de kaolin a été interprété a partir de profils de seismique-réflection à haute résolution, de sondages, et d’études minéralogiques sur un sondage de référence. Ce kaolin est un produit diagénétique précoce formé par de l’eau météorique sous le niveau de la nappe phréatique. La distribution du kaolin est contrôlée par la présence de zones de recharge associées à des discordances intraformationelles marquées par le développement d’oxisols au-dessus du niveau de la nappe phréatique. La présence d’interlits de grès perméables faiblement consolidés a contribué à l’efficacité de ce processus diagénétique. Les dépôts de kaolin les plus riches se trouvent en périphérie des rivières, là ou les boues de la plaine d’inondation n’étaient pas suffisamment bien drainées pour permettre le développement de paléosols, mais où des mouvements verticaux subséquents ont crée des discordances intraformationelles. La circulation d’eau météorique dans les grès a entraîné l’altération des feldspaths en kaolin, générant ainsi des dépôts économiques de sable de silice. Elle a aussi causé l’altération de l’ilménite en rutile, que l’on trouve dans des placers secondaires situés dans des rivières contemporaines qui ont érodé la Formation de Chaswood et les tills qui en sont dérivés."

Jan 1, 2006

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005