Search Documents

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

Orebodies of the Renison Bell - Mt. Bischoff tinfield in Tasmania are stratabound, conformable lenses of massive cassiterite-bearing pyrrhotite, with underlying discordant, fault-fracture-controlled and more siliceous ore. The deposits occur in eugeosynclinal, trough-deposited sedimentary and mafic volcanic rocks which are stratigraphically equivalent to diff erentiated volcanic rocks that contain volcanogenic massive base metal sulphide deposits in a parallel arc to the east. Textures of the massive pyrrhotite ore suggest that it has undergone metamorphic recrystallization. Although the massive ore contains both monoclinic and hexagonal pyrrhotite, a study of a few samples from one orebody suggests that their distribution is stratigraphically controlled, with the monoclinic variety abundant only at the base. The distribution pattern of rare-earth elements in massive ore is similar to that of volcanogenic massive base metal sulphides in New Brunswick, and suggests that mixing of sea water with exhalative hydrothermal brines occurred during ore deposition. Tin is a common accessory element in many volcanogenic massive base metal sulphide deposits providing strong evidence that it, too, is transported and deposited by volcanic affiliated hydrothermal brines. Sedimentary rocks containing the massive orebodies are fine grained, thinly laminated, compositionally banded and of mixed chemical sedimentary-tuffaceous origin. They include finely recrystallized chert, carbonate-rich and pyritic varieties; and soft sediment deformation structures in these rocks suggest that dense sulphides deformed underlying, less dense chert prior to lithification. Close to ore the chert becomes massive and coarsely recrystallized, as does the carbonate, which is here strongly enriched in Fe and Mn. Apatite is present in pyritic, cherty and carbonate-rich beds and in the ore itself, in all of which it shows a similar pattern of rare-earth element distribution, suggesting that it is of marine sedimentary origin. These deposits have traditionally been considered as epigenetic replacements of favourable carbonate horizons by hydro thermal flu ids derived from later Devonian porphyritic intrusions. Some of these intrusions have associated tinbearing greisens. The above relationships suggest, alternatively, that, like massive base metal sulphides, the tin deposits were of original syn-sedimentary origin. Circulating hydrothermal brines generated during early Cambrian eugeosynclinal subsidence and tectonism rose through steep fault-fractures, there giving rise to the discordant orebodies, and were discharged on the sea floor, where the massive pyrrhotite lenses were precipitated with the associated cherts and carbonates. In some places, Devonian intrusions remobilized the earlier deposits, forming greisens and newepigenetic veins. Finally , the geologic selling of these deposits, in trough deposited sedimentary and mafic volcanic rocks, suggests another favourable environment for massive sulphide exploration which is quite different from the domal felsic volcanic environment so heavily favoured currently in North America

Jan 1, 1979

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By Wei Sun, Xiangsong Meng, Xiaodong Li, Weisheng Huang, Yuehua Hu, Chonggao Cao, Haisheng Han, Wensheng Chen, Runqing Liu, Central South University

"The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work revealed the effect of water glass on the flotation of scheelite by FTIR and the wettability change of the usual cleavage plane, and proved that water glass inevitably influenced the flotation of tungsten minerals to a large extend in traditional fatty acid flotation process. A new collector, benzohydroxamic acid complexes, was found to be selective for the separation of scheelite and calcium minerals with little water glass. Hence a novel flotation process was developed for the recovery of tungsten minerals in shizhuyuan mine in China. Normal temperature flotation of tungsten minerals was developed to instead of the classical “Petrov's process” for scheelite-calcite-fluorite type ores. Compared with the traditional process, the recovery was improved by 10% and the grade of scheelite concentrate was above 55%. The disappearance or decreasing of water glass contributed to improving the recovery of tungsten and fluorite and the circulation of water and reagents.INTRODUCTIONChina is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves (Cai Gaipin et al., 2009). However the wolframite has been dried up and the scheelite resource has become the main resource of the tungsten metal. Scheelite deposits were classified to scheelite-silicate type and scheelite-calcite-fluorite type based on the associated gangue minerals. Scheelite was easy to separate from the silicate minerals. Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physicochemical characteristics such as solubility, hardness, specific gravity, PZC (point of zero charge) etc.(Arnold & Warren, 1974; Yongxin & Changgen, 1983; Ozcan & Bulutcu, 1993a; Deng et al., 2015, 2016;). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives ( Yongxin & Changgen, 1983; Oliveira & Sampaio, 1988; Sivamohan, 1988; Shi et al., 2014; Bo et al., 2015). It is difficult to separate scheelite especially from calcite with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan & Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is not adequate for a low-grade calcitic scheelite ore. Unfortunately, the reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Yongxin and Changgen, 1983; Schubert et al., 1990; Shi et al., 2014; Bo et al., 2015) used for calcite depression also depress scheelite to a large extent."

Jan 1, 2016

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By Robert Lee

"International competition is presenting the Canadian steel industry with a major challenge. While Canadian companies have invested in new technology, research and development, activity by Canadian industry, in general, lags significantly behind that of its major competitors. While OECD countries increased their research and development spending during the 1980s, Canada's R&D funding levels have changed little since the early 1970s and have actually dropped since 1986, despite greater public discussion on the issue. This fact is reflected in the relatively slower pace of innovation in the Canadian steel industry, despite the efforts of both government and industry.In addition, there are a number of factors that undermine the competitiveness of the Canadian steel industry, in particular in relation to the United States. Among these are higher interest rates, labour costs and tax rates, as well as an overvalued Canadian dollar. Canadian steel companies are thus feeling the full impact of the current economic recession. This recession, combined with recent strikes, have, for example, caused serious losses for Algoma and Stelco.In spite of these objective difficulties, the Canadian steel industry has been able to survive and continues to strive for a leadership position in the world market. Since World War II, heavy investment in new technology has allowed the industry to upgrade its facilities and increase productivity, while at the same time improving quality and reducing pollution. This last point is particularly important in view of public insistence on improvements to the quality of the environment. Over the next decade, this technological innovation must be maintained and intensified if industry is to meet the challenge of international competition and attain a leadership position."

Jan 1, 1991

By V. Caps

Gold has been often used as an alloying component in order to increase or modify the catalytic properties of an active metal. For example, in the hydroconversion of methylcyclopentane, Riahi et al [1] shown that the addition of gold to palladium or platinum enhances the activity which becomes greater than that of the pure metals whereas the selectivity towards products resulting from ring expansion increases. Molenbroek et al [2] presented a detailed study on Ni-Au catalysts which exhibit activity for steam reforming and have been proved to be more resistant toward carbon formation than the pure Ni catalysts. Blocking of highly reactive Ni edge and kink sites by Au atoms is assumed to be the reason for the increased robustness of the Ni-Au catalyst. Nevertheless, the own catalytic properties of pure gold have been almost ignored up to the pioneering work of Haruta et al [3] which demonstrates the high activity of gold for CO oxidation at low temperatures. Other reactions such as WGS reaction, propylene epoxidation or benzene total oxidation have then been shown to be catalyzed by gold [4]. This discovery induced the publication of papers devoted to analyze the different factors controlling the activity of gold catalysts. Among them the most relevant appears to be the gold particle size, the nature of the support [5] and the preparation methods [6]. Clearly distinguish between support and size effect is not straightforward. Indeed, the calcination step often needed to synthesize supported catalysts on different supports, leads to different particle sizes showing that particle size and support are interdependent. To circumvent this difficulty, Au-based supported catalysts have been synthesized by using laser vaporization and low energy cluster beam deposition. The as prepared catalysts have then been characterized and tested in CO oxidation reaction.

Oct 1, 2003

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

McArthur River Operation is the world?s largest high grade uranium deposit and is located in Northern Saskatchewan. McArthur River came into production in December 1999 with a number of innovative technologies to allow for mining of a high grade uranium deposit in challenging geotechnical and hydrological conditions. The raisebore mining method has been supplemented by the continued development of a boxhole mining technique to allow for mining of mineralization that cannot be accessed with a drill chamber from above. An innovative freeze wall re-design ? a cathedral freeze wall, was implemented in 2009 to allow for top access of a new orebody in the unconformity area of the Athabasca Sandstone. This paper highlights some of the ongoing improvements to the mining method and the innovative risk mitigation applied to manage the extraction of this challenging orebody.

May 1, 2011

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributableto accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company's total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company's historical results of operations is set forth in the notesto the financial statements included in the Company's Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By V. “Ram” Ramachandran

"In view of the increasing number of environmental regulations that have been promulgated all over the world in the last thirty years, non-ferrous smelters and refineries have had to learn and adapt to treating process bleed waste streams containing heavy metals. The result of such treatment invariably yields a gypsum-saturated solution containing salts such as alkali metal sulfates, chlorides and fluorides. Presence of anions such as sulfates, chlorides and fluorides in the discharge streams – presently not a major problem- are coming under increasing scrutiny and will have to be addressed in the near future. It is envisaged that discharge limits for sulfate ions will be in place in the near future. Treatment of brackish water to produce drinking water also results in brine streams containing alkali salts that have to be addressed for proper disposal. This paper reviews treatment options for such streams containing high levels of total dissolved solids with emphasis on sulfate removal. Areas covered would be: a) chemical treatment for removal of various constituents that make up the total dissolved solids b) processes for sulfate removal processes –thermal and non-thermal-to recover and reuse of treated water and c) brine use and treatment options.INTRODUCTIONThe rising cost of water and meeting the ever-changing stringent environmental discharge regulations make water recycling and reuse essential. The metallurgical industry has used water as a medium for dissolving and/or rejecting metals and chemicals in addition to removing thermal energy. Any excess process effluent is collected and sent to end-of-pipeline treatment and ultimately discharged to surface water for disposal under a permit. The conventional- and probably the cheapest way -of treating metal-bearing process effluent streams is lime neutralization followed by sulfide polishing for elimination of heavy metals to produce a stream that meets NPDES discharge limits. This results in a stream containing dissolved solids.These dissolved solids normally comprises of inorganic salts. The possible constituents are cations calcium, magnesium, sodium and potassium. The anions are sulfate, chloride, fluoride, nitrate, carbonate and bicarbonate. In addition to these constituents, the treated effluent streams contain very small amounts of heavy metals, oxyanions such as arsenites, arsenates, selenites and selenates. Process streams from gold operations contain residual cyanide. Small amounts of ammonium ions are also present in these streams based on the pH of the solution."

Jan 1, 2012

By James R. Hunter, Sandra K. Zacharias, Ursula M. Franklin

Archaeometallurgical remains can be a valuable source of information about past technological activities and, by inference, the societies that undertook them. Material traces of former metal-producing or metal-working centres can include raw materials, products, or metallurgical installations such as mines, furnaces or forges. Of these remains, the most common is slag, often left undisturbed since its original production. Physical and chemical analyses of archaeological slag and metal can often reveal the processes and materials involved in their formation. Mineral composition and softening temperature of a slag, for instance, can indicate the conditions of the metallurgical operation, such as temperature and atmosphere and, thus, help identify metallurgical processes which took place at a site(1). The present report illustrates the value of such analysis. Metal-working remains from Sainte-Marie among the Hurons, near Midland, Ontario, on the south side of Georgian Bay have been analyzed in order to determine the techniques and processes used by the 17th-century blacksmith who worked at the mission headquarters from 1642 to 1649. Samples were selected from a very large collection of blacksmith refuse which was excavated from the site by archaeologist Kenneth Kidd in 1941-42(2).

Jan 1, 1999

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015