Search Documents

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By W. A. Lang

Introduction That the coal industry has entered a new phase in its development is now evident. Coal, besides being the chief source of heat and power, has become a potential raw material for many industries. Rapid progress has been made in the methods used in the mining and preparation of coal, and in the equipment for the burning of coal. Data of a fundamental nature relating to the composition of coal and to its transformations? during combustion and processing have also been revealed. Research, the key which has opened this new era, has already accomplished much, but it has only begun to show what it may and should be able to do. New developments of coal burning equipment, super-power plants, carbonizing and briquetting plants, hydrogenation and synthetic chemical processes, will undoubtedly have a marked influence in the post-war years on the economic welfare of many coal producing countries. Until comparatively recently, however, there has been in many branches of the coal industry a tendency to regard research as something abstruse and something which had little or no value to those managing such branches. But the fact that coal has suffered as a source of heat and energy through inroads of oil, natural gas, and water power, has made it plain to the industry that, if it is to maintain its present markets in this competitive world, much less increase them, the whole industry must be willing to follow the example of other industries and plan for the future.

Jan 1, 1946

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961

By S. B. V. Stewart, W. W. Forsyth

"Since the Mathew's method for open stope design was first proposed by Golder Associates in 1980 it has been applied at a number of mine sites in Canada. The initial hypothesis was based on a relatively small amount of data and the intervening period has allowed the collection of a significant amount of new data to test the validity of the method.This paper examines a brief history of the evolution of rock mass classification systems to provide background and emphasize their empirical and non-rigorous approach. It also presents the new data which appear to indicate that the initial hypothesis was reasonably good. The modification to the original graph proposed by Potvin is discussed as well as the applicability of the method to predicting the onset of caving. The original graph has been updated and has been subdivided into four zones described as ""stable""; ""potentially unstable""; ""potential major failure""; and ""potential caving"". The method is recommended as a useful open stoping design tool provided it is recognized that it is not a rigorous design method.Finally the paper proposes a recommended approach for application of the method by would-be users and addresses some typical pitfalls that may be encountered."

Jan 1, 1995

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By V Dolmage

In 1957 and 1958, ten topographically suitable damsites were investigated along the Peace river between Finlay Forks and Hudson Hope, B.C. Of these, three were eliminated after a reconnaissance survey indicated that the geology was unsuitable for the 650-ft.-high dam contemplated. ?After extensive drilling, five other sites were deemed unfeasible because of geological factors and, in 1959, the two remaining sites were designated as being suitable, one for the high dam and the other for a low dam downstream. The sites are located in the Peace River canyon, on the west and the south? side of Portage mountain, west of Hudson Hope. The site for the large dam, the Portage Mountain dam, has since been investigated by surface mapping, thousands of feet of diamond drilling, a seismic survey, laboratory rock tests and on-site grouting tests in order to establish the possible effect on the dam of all facets of the foundation rocks. Three diversion tunnels, 50 ft. in diameter and 2,200 feet in length, have been driven through massive sandstone and shale, and an intake cut, 500 ft. in length, 200 feet in width and 200 feet in depth, has also been excavated in rock.

Jan 1, 1963

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By L. R. Bottomer, G. M. Leary

"The Copper Canyon property is located in the Galore Creek area of northwestern British Columbia. Porphyry copper-gold mineralization on the property is notable for its high gold content and close spatial relationship with a distinctive suite of high level syenitic and monzonitic intrusions, and pseudoleucite-bearing volcanic country rocks. The style of alteration and mineralization is similar in many respects to the nearby Galore Creek deposits.The current geological resource of 32.4 million tonnes grading 0.75% Cu, 1.17 g/ t Au and 17.1 g/t Ag is insufficient to support a mining operation, but definition of additional reserves combined with improved transportation infrastructure in the region may change this in the future. The climate, topography and proximity to an active glacier indicate that the most likely production scenario is an underground bulk mining operation, with the ore being milled offsite.IntroductionThe property is located at 57°07' North latitude, 131 °21' West longitude, on NTS sheet 104G/ 3W, approximately 160 km northwest of Stewart and 90 km south of Telegraph Creek (Fig. 1). The Galore Creek camp and airstrip are located 6 km to the west. Current access to the property is via helicopter either from Galore Creek, or from the Bronson Creek airstrip 32 km to the south-southeast.The deposit occurs within the Boundary Ranges of the Coast Mountains, on the north side of the east fork of Galore Creek, which flows northerly into the Scud River and thence westerly to the Stikine River.Topography is rugged. In the deposit area, elevations range from 1130 m to 1750 m. Valley glaciers and permanent snow and ice fields are characteristic of the region at these elevations, and at its southern limit, mineralization is truncated by the East Fork Glacier.The property is entirely above the treeline, and except for areas of moraine cover and talus slopes, outcrop is abundant."

Jan 1, 1995

By C. Joulian, A. G. Guézennec, A. Chmielarz, Y. Ménard, M. Hanke, P. d’Hugues

"The copper concentrate used in this study is produced by flotation of a black shale organic rich ore. This resource is a carbonate-rich, polymineral concentrate. In the last 5-6 years, ore characteristics changed and the concentrate grades degraded. This study evaluated bioleaching of the concentrate in stirred tank reactors as an alternative to the pyrometallurgical technology that is currently applied, and which may no longer be feasible in future given the concentrate chemistry.The first part of the study focused on testing non-traditional operating conditions during continuous bioleaching experiments: high solids concentration (> 20% solids), reduced agitation and aeration rates. For the same residence time, bioleaching performance at high solids loading (25%) was the same as that reached during previous bioleaching experiments at 15% solids. No mixing or microbial issues were encountered. The bacterial consortium used in the experiments demonstrated a high copper tolerance.The second part of the study was devoted to technology development for metal recovery from copper bearing solutions obtained during bioleaching experiments. Due to the high copper concentration of the leachate, solvent extraction prior to electrowinning was not necessary. After iron removal, high quality copper cathodes (morphology and composition) were obtained from the PLS by electrowinning."

Jan 1, 2014

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By E. A. G. Colls

PART I.-GASES IN INDUSTRY INTRODUCTION THE part played by gases in industry can be considered from at least four distinct viewpoints, viz: (1) As air to support combustion and life and do various kinds of work (2) As fuel, or as essential to certain chemical processes (3) As sources of danger from explosion or fire ( 4) As hazards to man's health The present paper deals with gases only insofar as they are sources of danger, or are hazards to health. It may be noted, however, that, in point of tonnage, air is one of the most important materials handled in any industrial plant. In the operations of the Consolidated Mining and Smelting Company, for example, 138,000 tons of air are handled daily, the only material exceeding this figure being water. The United States Bureau of Mines has listed no fewer than seventy-four gases and vapours that, under certain conditions, may be considered as ex-plosive or dangerous (poisonous). The commonest and most important of these are as follows : Carbon monoxide Methane Acetylene Hydrogen Oxygen Hydrogen sulphide Benzol vapour Ammonia Petroleum vapour Carbon disulphide Hydrochloric acid gas Cyanogen Carbon oxysulphide Chlorine ` Fluorine (and fluorides) Acetone vapour Acetic acid vapour Water gas Natural gas Gasoline vapour Coal gas Producer gas Ether vapour Nitrogen oxides

Jan 1, 1940

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By W. E. Halle, G. J. S. Govett

"The Institute of Applied Geology, Manila, Philippines, is jointly sponsored by the University of the Philippines, the Philippines Bureau of Mines and the United Nations Development Programme (Special Fund). It provides, in its fourth year of operation, an interesting example of international cooperation in mineral development. Objectives include: (1) the training of mining engineers in modern techniques of mineral exploration; (2) assisting government and industry in discovering new ore deposits; and (3) providing the basis for the establishment of an economically oriented graduate school of geology at the University, the first of its kind in the country. Training of engineers requires roughly one full year, which is divided between academic study and actual field practice. Lecture and laboratory instruction include courses at university level designed specifically to up-grade those aspects of the geological sciences that are required by mining engineers now qualifying as mineral exploration engineers-economic geology, applied geochemistry, geo-physical exploration, petrology and structural geology. The field training involves direct participation in actual mineral exploration projects arranged with the co-operation of the Bureau of Mines and private interests engaged in mineral development and production. The system works well in practice, and the Institute staff and trainees were responsible for outlining new evidence of economic mineralization. It is also apparent from the application of the exploration methods available to the project -geological mapping, air photo interpretation, magnetic, electric, electromagnetic, self potential and gravity surveying as well as geochemical prospecting -that, under the humid, tropical, mountainous conditions in which the practical program was conducted, air-supported geochemical prospecting with attendant reconnaissance geological mapping affords the most economical and effective approach to mineral exploration for at least some of the deposits characteristic of the region."

Jan 1, 1968