Search Documents

By E. Shum, V. G. Papangelakis

"Attempts to reduce the energy requirements of water recovery in the process industries have resulted in the development of techniques to freeze and purify aqueous solutions that take advantage of local climatic conditions. Natural freezing is a technique by which aqueous solution is exposed to freezing air temperatures, resulting in the production of a layer of ice on the surface. As the ice layer tends to exclude solute, a concentrated solution is formed. However, due to dendritic ice growth along the advancing growth front, small quantities of solution are trapped within the ice, decreasing the purity of the water recovered. The ice produced can then be allowed to thaw in order to recover the water using low grade plant heat. As the more concentrated parts of the ice melt first, a purer ice remains. In this study, 0.5 molal magnesium sulfate solution was frozen under simulated natural freezing conditions at temperatures between –1 and –6°C. The ice produced was thawed at either room temperature or 50°C. Up to 40% of the water was recovered with a separation efficiency of above 95% when thawing at room temperature.INTRODUCTION Advances in refrigeration technology have made low-temperature separation processes increasingly appealing to an energy-conscious society. The latent heat of freezing of water is about seven times smaller than the latent heat of evaporation providing freezing with a strong thermodynamic advantage over the traditional evaporation-based processes. The result is the development of a wide variety of processes that fall under the term Freeze Concentration (FC), which describes a variety of techniques in which an aqueous solution is concentrated by the creation and subsequent removal of ice (Williams et al., 2015).FC processes exploit the freezing behaviour of aqueous solutions as dictated by their respective water-salt phase diagram. When, for example, a solution of magnesium sulfate is cooled to a temperature below its freezing point but above its eutectic temperature of –4.1?C (Figure 1) then, if the concentration of MgSO4 is less than the eutectic concentration (about 1.7 m), ice will form until the solution concentration reaches its equilibrium concentration at the given temperature on its phase diagram. If the concentration is greater than the eutectic concentration, MgSO4 solid will precipitate until the concentration reaches equilibrium. It is for this reason that ice can be selectively produced in FC processes (Randall & Nathoo, 2015)."

Jan 1, 2017

By J. S. DeLury

The last few years have been eventful ones for Manitoba in connection with mineral development. Perhaps the past year has been the most important of all. It is therefore a suitable time to review the mining situation in the Province. In order to obtain, in the following paper, a proper set ting from which to discuss the trend of recent developments, a brief review of the story of mining will first be given. This will include a summary of a few of the outstanding facts regarding prospecting, discovery, and operations in the several known metalliferous areas of the Province. Following this will come a more detailed description of activities during the past year or two. Special attention will then be paid to the outstanding enterprises, such a~ those associated with the names of Flin Flon, Sherritt-Gordon, and Central Manitoba, names which have been attracting the attention of the mining world to Manitoba. And last of all will be presented a brief summary of mineral production, which, so far, has largely been credited to non-metallics. HISTORICAL To aid a proper comprehension of the recent trend in mining, it is well not to lose sight of the history of development in the different metalliferous areas in Manitoba. This Province seems throughout to have been more or less dependent on mining interest excited by discoveries in the neighbouring province of Ontario. The first interest came as an effect of the Lake of the Woods mining boom, when small adjacent parts of Manitoba were prospected. Several discoveries were made, but no mining industry resulted.

Jan 1, 1929

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

"An unparalleled growth in the Canadian coal industry in 1970 coincided with increasing awareness by Canadians of their environment and their geography with its accompanying transportation factors. R and D on coal moved with greater emphasis toward solving problems in these areas as well as continuing with strong interest in coal preparation, carbonization, combustion, ""weathering'', spontaneous ignition, storage, exploration and geology. Long-range ""basic"" research was not forgotten in that work continued on coal-based carbons, coal chemistry and agrobiological uses for coal. This paper reviews the status of these many areas of coal research at the beginning of the seventies and takes note of some of the more significant legislation and projects brought to the author's attention. No attempt is made to itemize or to describe in detail all the worthwhile projects, many of which are reported elsewhere."

Jan 1, 1971

Of the many organic impurities present in Bayer liquor, sodium oxalate is known to have one of the most detrimental effects on the Bayer process. Because of its limited solubility, it will co-precipitate with gibbsite during the precipitation stage which results in many operational challenges for the refinery. Despite the importance of this phenomenon, the interaction mechanism between gibbsite and sodium oxalate is not well understood. In this study, the growth of sodium oxalate on three main morphologies (random agglomerates, prims and hexagons) of water-washed and caustic-washed gibbsite was observed under synthetic Bayer conditions using in situ optical microscopy. After a short induction period, oxalate started to nucleate on gibbsite crystals, and grew with a needle-shaped morphology which eventually developed into oxalate bundles. In addition, the results indicated that caustic washing was able to partly decompose gibbsite crystals and thus make the gibbsite surface rougher, which provides more potential sites for oxalate nucleation and growth. The growth rate of oxalate crystals on the basal (001) face of water-washed gibbsite was 1.33 µm/min determined by the time-lapse imaging of in situ optical microscope.

Jan 1, 2014

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By C. G. Harris, R. Sluyter

The purpose of an undercut is to undermine a block of ore which will then proceed to cave into draw holes just below the undercut. Undercut-ting is the final and most vital phase in the development of an ore block. Since its purpose is to undermine and induce caving into a block of ore, great care must be exercised to avoid premature caving by removing only enough rock to permit undercut development to proceed. Several undercutting methods, used over a twenty-year period, are re-viewed and their suitability is com-pared with ideal requirements.

Jan 1, 1960

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By J. E. Hawley

Introduction The Siscoe gold mine is the most easterly producer of gold from deposits lying in the belt of Keewatin and Timiskaniing rocks which extends east from Kirkland Lake, Ontario, and on through the Rouyn copper area. Unlike many of the deposits in this belt, those of Siscoe are contained almost entirely in a stock of much-altered granodiorite which intrudes Keewatin lavas. They are situated on an island of about one square mile in area, lying in lake De Montigny, Dubuisson township, 40 miles south of Amos, on the Transcontinental branch of the Canadian National railways, and 52 miles east, and slightly south, of Noranda. Geographically, the deposits are favour-ably situated with respect to transportation facilities, a through water-route being available from Amos, along the Harricana river and its lake expansions. The deposits consist of auriferous quartz-tourmaline veins of the fissure-filled type and are of particular interest because of their geological structure and genesis. Furthermore, deposits of a similar type occur both in the Keewatin and in granodiorite bodies to the east, in Dubuisson, Bourlamaque, Pascalis, and Louvicourt townships, and it is hoped that the following discussion may be of some aid in the exploration work now being carried on throughout this general area.

Jan 1, 1932

By W. Kunda, J P. Warner

SHERRITT GORDON Mines Limited annually produce 300,-000 pounds of pure cobalt by processing a nickel-cobalt-copper-iron sulphide ore which is mined at Lynn Lake, Manitoba. The ore (containing 0.04 per cent Co) is •concentrated to give a concentrate containing l 1-12 per cent nickel, about 2.0 per cent .copper, and 0.25-0.35 per cent cobalt, which is treated at the Refinery in Fort Saskatchewan, Alberta. The concentrate is leached in an ammoniacal solution of ammonium sulphate using compressed air as the oxidant. After filtration the leach solution contains, besides nickel and cobalt, copper ammines, sulpharnates and salts of various thionic acids. The copper is removed by precipitation as sulphide and the sulphur compounds converted to ammonium sulphate by a combined oxidation and hydrolysis treatment. The purified solution •Containing about 45 gpl of nickel and 1 gpl of cobalt is treated with gaseous hydrogen under pressure at 350°F to precipitate metallic nickel powder, the precipitation 'being terminated when the nickel content of the solution is about 0.8-1 gpl. Only about

Jan 1, 1962

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By M. H. Attia

The concept of sustainable development has been evolved into a working framework for sustainable manufacturing, in which the environmental requirements are introduced into product development at the design stage. This keynote paper is discussing a number of issues pertaining to the impact of manufacturing on the environment. The conflicting requirements of sustainable development, sustainable manufacturing (SM) and economical growth are presented in the light of successful case studies that were able to convert conflicts into opportunities. Integration of SM into the product life cycle is also presented. A number of concepts that are related to Ecoefficiency, e.g., inverse manufacturing, demanufacturing and re-manufacturing are also discussed. The paper underlines the fact that the positive impact of this new philosophy is equally applicable and beneficial to both; developed and developing countries. The paper concludes with an overview of Global trends in environmentally benign manufacturing (EBM); e.g., product-take back and emerging material and processing technologies. The state-of-the-art approach to Life Cycle Impact Assessment and integration of design for the environment DfE principles are demonstrated through some case study.

Jan 1, 2006

By J. L. Jambor, R. W. Boyle

"The Magnet Cove barite-sulphide deposit is a raking pipe-like body that replaced and partly filled a large brecciated zone at the junction of two faults at the contact between sedimentary rocks of the Horton and Windsor Groups of Mississippian age. The principal minerals in the deposit are siderite, barite, hematite, pyrite, marcasite, galena, sphalerite, chalcopyrite, tennantite, proustite, pearceite, acanthite and stromeyerite. The mineral assemblage and textural relationships indicate that the minerals were deposited from low-temperature solutions. The source of the elements in the deposit is believed to be the enclosing sedimentary rocks, with connate or ground waters as the transporting medium, and solubility products as the governing factor controlling the abundance and order of deposition of the minerals."

Jan 1, 1966

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l'Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933

During the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits. However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses haw not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently am poorly doc-umented, the use of these terms is reviewed. Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco's Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delin¬eation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study. The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit by 39.27% and 45.41%, respectively, and that of the 6 m wide deposit by 12.84% and 11.55%. As the impacts of ore loss and those of dilution on the net present value am almost identical in these simulations, we could, in practice, assume a 50/50 split between dilution and ore losses in such a case. These results do no take into account the effects of local optimization measures taken at the mine production level (blasthole sampling near stope limits, etc.) The potential impacts of geological and sampling uncertainties in terms of lower NPV justify and require more systematic efforts to ensure that deposit appraisal work and feasibility studies are adequate to optimize company revenue and competitive returns to investors from mine production activities.

Jan 1, 2005

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952