Search Documents

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By H G. Poulos

Prediction of ground deformation caused by soft ground tunnelling is an important problem facing design engineers. The ground deformations are caused by the closure of the gap formed around the tunnel due to the tunnelling procedure and soil intrusion via the tunnel face into the tunnel. There are three different approaches that are commonly used in practice to estimate the ground deformations due to tunnelling, namely, empirical methods, analytical methods and finite element methods. One of the important issues of tunnelling in urban areas is the assessment of the likely impact on adjacent pile foundations of ground movements arising from tunnel construction. The main objectives of this paper are two-fold: first, to assess the available methods to estimate the tunnelling-induced ground deformations, and second, to examine the effect of such ground deformations on adjacent piles. Analytical solutions to predict the tunnelling-induced ground deformation developed by the authors are used in this study. These estimated ground deformations are imposed on the pile in simplified boundary element analyses to compute pile responses. The influence of various factors such as tunnel geometry, ground loss ratio, pile diameter and ratio of pile length to tunnel depth are examined in this study.

Jan 1, 1999

By R R. J McAllister, K Moffat, S Heyenga

This paper examines the statistical relationship between quality of life indicators and the gross value of mineral production from Australian regions. We used quality of life indicators, aggregated for 673 local government areas, of household income, housing affordability, access to communication services, educational attainment, life expectancy and unemployment. We find no evidence of systematic negative associations between quality of life and the gross value of minerals production. Instead, mining activity has a positive impact on incomes, housing affordability and communication access across regional and remote Australia. Whilst we do not establish causality between mining activity and quality of life, our analysis prompts a rethink of the æresource curseÆ as it applies within a single country. Nevertheless, our findings are tempered by extensive anecdotal and empirical evidence of the negative social impacts of mining on specific demographic sectors, localities, families of fly-in, fly-out mining operations and individuals. This contrast may be a scale issue, with the regional benefits of mineral wealth masking highly-localised inequalities and disadvantage. We suggest that there is a need to better understand these impacts and, more importantly, the types of policy mechanisms government and industry can adopt to mitigate or avoid them.

Jan 1, 2009

By B BussiFre, J Molson, M Aubertin, G W. Wils

Waste rock piles containing reactive sulfide minerals can serve as long-term sources of acid mine drainage (AMD). Within these piles, many physical, geochemical and biological processes can contribute to the production of AMD. The flow of water, for example, depends on internal pile structure, which depends on the dumping methods used to construct the pile. In this paper, the internal structure and grain size distribution of typical waste rock piles are first reviewed with respect to their effect on internal water flow. A numerical model is then applied to simulate unsaturated flow within a waste pile assuming two primary waste materials, different atmospheric conditions and several geometric configurations. The simulations suggest that water movement can be controlled by introducing fine-grained material layers within the coarser host material. However, these layers should not be horizontal because they can lead to localised high-saturation regions as well as preferential flow favouring the production of AMD. A shallow slope towards the pile boundary may be introduced to force drainage to the outside while maintaining low saturation within the interior, thus reducing the production of AMD.

Jan 1, 2003

By G Ferguson a, P Carrasco, P P. A Dowd

International codes of practice offer broad definitions with respect to the classification of resources in terms of risk. Specific guidelines and protocols, to analyse sample data, carry out geostatistical appraisals, develop geological models and finally estimate and classify resources, are not addressed. Neither are detailed requirements for engineering mineable reserves from estimated resources. In addition, international codes of practice fail to distinguish between types of deposit, other than in broad terms, as for example, The AusIMM JORC Code (JORC, 1999) which makes reference to diamond and coal deposits. The objective of this paper is therefore to set in motion the process of specifying detailed protocols, acceptable to the international community, for the assessment, reduction and management of risk associated with the development and extraction of mineral deposits. Ordinarily, the main risks and issues encountered during the process of estimating resources and subsequent conversion to reserves, encompass:failure to understand relevant geological controls of mineralisation; validation of grade interpolation; optimism in geotechnical appraisals of dilution and stability and the consequent selection of inappropriate mining methods; metallurgical modelling of minerals and contaminants reporting to concentrates; appraising the hydraulics of heap leaching and the numerous factors that can affect recovery; difficulty of managing metal price cycles and changes in regulations within the constraints of long-term mining plans; and development of better evaluation techniques for mining ventures. Uncertainty is inherent in estimation and engineering work, and its identification, reduction and management should be a fundamental goal of all involved in the mining industry (Figure 1). Variability may be reduced by:following internationally accepted practices for the collection, manipulation and analysis of geoscientific data; and verifying that the procedures actually performed meet the associated standards. Increasing amounts of data will also reduce uncertainty, but only if the procedures used to collect and appraise such data follow the relevant procedures. It is thus the aim of a series of papers in preparation, Beniscelli et al (in prep), to put forward detailed guidelines, for:project sponsors û to provide a global view of the work and documentation needed to support requests for funding various phases of project development and budget approvals; geologists û to indicate a checklist of the requirements and standards for the exploration and estimation of resources; and engineers and economic analysists û the protocols for characterising, modelling, engineering and evaluating the extraction of reserves. It is therefore hoped to encourage the development of consistent standards for declaring reserves within the mining industry. Data from projects and operations will be utilised to illustrate the benefits of adopting a rigorous approach to estimating resources and engineering reserves, Beniscelli et al (in prep).

Jan 1, 2000

By I Auranen, J Raatikainen

IMA Engineering (IMA) and Mine On-Line Service (MOLS) companies have used on-line sensors for analysing ore and waste rock in mining for more than 25 years. Today IMA on-line sensors are used in various stages of the mining process including on-line analysis of drill cores, drill chips, ore and waste in loader bucket, ROM ore analysis on belt conveyor belt and in bulk ore sorting and in slurry analysis in concentrators. During years of extensive field experience and testing we have found that the waste rock dilution and ore losses create much larger economic and environmental losses than has been previously recognized. According to our studies the main reason is limited number of analysis already in exploration when drill cores or drill cuttings are used in block modelling. The same happens in production because too few and biased samples from benches are used to estimate the ore grade. Much more than today estimated amount of waste enters the mill and considerable volumes of ore losses happen at the same time. The ore grade on the benches and in muck piles is averaged and “homogenized” with averaged and biased samples. These are the main root causes of waste rock dilution and ore losses. Sensor based preconcentration can be the remedy to waste rock dilution and ore losses. This presentation will show examples of the use of on-line sensors in preconcentration when analysing ore and waste rock in drill cores, drill cuttings, on conveyor belt and in bulk ore sorting. Waste rock removal in preconcentration has direct effect on energy consumption in crushing and grinding and chemicals in concentrator. In concentrator waste is separated and goes to tailings pond, however, preconcentration directly reduces the volume of the tailings. In our presentation we will cover cases in base metals and in gold mines.

Nov 10, 2020

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J-P Franzidis

Mill operators have traditionally been forced to rely on grade-recovery curves and overall flotation rate constants when analysing proposed improvements to plants. This has led to loss in money and time when a proposed change that showed potential in laboratory scale tests failed to show improvement in the plant. Frequently, this is a result of the operators being unable to gain insight into how and why the proposed change affected the flotation performance. This is due to the classical models not including any description of the subprocesses of flotation and their individual contribution to the overall flotation performance. A new flotation model has been developed as part of the AMIRA P9 project that separates the flotation process into subprocesses and includes the contribution of both the pulp phase and froth phase to the overall flotation recovery. It is not possible to determine the individual components of this new model on traditional pilot plants as they lack the required flexibility and scale. Therefore a new pilot plant has been developed known as the Floatability Characterisation Test Rig (FCTR) that has the flexibility and features required for the determination of the flotation subprocesses. The flexibility and features of the FCTR also make it an ideal tool for investigations into many different aspects of flotation research. These include the effect of reagents, grinding, and power on the flotation performance. This paper will describe the methodology for using the FCTR in these fields of research and highlights the advantages of using the FCTR over traditional methods.

Jan 1, 2000

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

A mining operation can be identified as demonstrating prudent management when a number of vital characteristics are evident.All risks and opportunities that are critical to the on-going success of the operation have been identified and are being effectively managed. All significant tasks and events are plan driven. All levels of management visibly support the policies of the operation through their attitude, behaviour and actions as well as words. Supporting evidence for required activity and the outcomes is readily available. Improvement mechanisms are working to advance the key business processes. Everyone is working towards satisfying the needs of the stakeholders of the operation. When these characteristics are integrated with the satisfaction of all legislative requirements, all industry codes and optionally all relevant international management system standards then an operation is fulfilling all the requirements of a Due Diligence Process. The majority of mining operations do not show all of these characteristics and therefore unnecessarily suffer from missed profit opportunity and constant cost pressure, less than acceptable safety and health and environmental performance and consequent poor relations with employees, unions and regulators. In these operations the characteristics to be observed are quite different.Serious incidents are occurring with no sign of a rate decrease. The operation lurches from one panic ituation to another. Management are absent in their leadership, but very active in developing rules and enforcement methodologies. The operation has no history. Re-inventing the wheel with employees who come and go at an alarming rate seems to be forever occurring. All efforts are directed at controlling the business outputs with a strong emphasis on blame. Everyone is trying to look busy to avoid the ever-present cost reduction threats. To change to more prudent management utilising a Due Diligence Process is not theoretically difficult. However it does take clear direction, focussed efforts, supporting actions with appropriate tools and perhaps most importantly an internal desire and drive to become such an operation. A Due Diligence Process is about doing the important things that have to be done, providing the understanding of why they are important, demonstrating proof of activity and effectiveness, and leading the way through effective management.

Jan 1, 1998

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

By R H DAVIES

Peak Gold Mine is a new gold and base metal mining project being developed by Enterprise Metals (a 100 per cent subsidiary of CRA) at Cobar in the centre of New South Wales. The Cobar district has a long history of copper and gold mining operations stretching back to the 1870s. Extensive gold and base metal mineralisation was discovered at the Peak in 1981 below a series of gold mines which had been active around the turn of the century. Evaluation of the deposit through the 1980s led to CRA's decision to develop the project for production at a capacity of 450 000 tonnes per annum in late 1992. The project has been developed with a green fields approach despite the long history of mining in the local area. This approach has lead to several innovative ideas being trialed at the site which are expected to result in the operation being a low cost producer of gold and base metals.

Jan 1, 1992

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011