Search Documents

The effect of temperature, time and SO2 concentration in the atmosphate have been studied for a complex Pb-Zn concentrate, which contained four sulphides and some organic material, in order to determine optimum roasting conditions. Under static roasting conditions virtually complete sulphation was achieved after roasting at 650¦C.2 hours in 10% SO2 in air. Both zinc ferrite and zinc silicate were observed to form early in the roasting, but continued exposure to SO2 -containing gases caused decomposition of these as the roasting time increased. Water and acid solubilities of iron, silica, calcium, magnesium and aluminium in the calcine were determined, as a function of roasting time, temperature and atmosphere composition.

Jan 1, 1970

Investment decisions in the Australian mining industry are often made without awareness of the impact of risk on project outcomes. A fundamental change in thinking is required to move away from the traditional attitude of æcushioning the blowÆ towards a measured approach to project risk. Such an approach involves quantifying and understanding project uncertainty so that investments may be shielded from downside risk while at the same time exposed to upside potential. Communication and collaboration between study teams and corporate financial managers must be improved before the industry can improve its project investment record. Monte-Carlo simulation provides a way to quantify and understand investment risk, but its accuracy depends on how well the variability of input parameters is estimated. Research in this area is currently centred on quantifying uncertainty in mineral resource estimation using new conditional simulation techniques, but a less-rigorous method can be applied in practice to begin the education process and develop the required awareness at board level.

Jan 1, 2003

By Restarick CJ

A compound cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone, has been used for coal slurry sizing experiments in the range approximately 100 to 300 micrometres. An important feature of the system is the ability to adjust the cut size of the separation over wide limits by adjustment of the flow control valve. Results have been compared with typical fine screening operations. Under roughly equivalent conditions the compound cyclone system can achieve better elimination of extreme fines, but is not as sharp as the screen for coarser size cut-off. Simulations of systems involving combinations of the cylinder-cyclone system with screens indicate that the advantages of both sizing devices can be combined to yield accurately sized products for fine coal cleaning, at much less cost than using screens alone.

Jan 1, 1984

There are two main areas of application of geology in quarrying: (i) In regional planning for industrial mineral requirements.(ii) In direct quarry management. The regional planning requirement has recently become more evident because of greatly increased land demand conflicts around cities. The direct quarry involvement is a reflection of both the economy and the greatly increased sophistication of the quarry industry. Here, professional planning and development expertise by a geologist is required, to ensure continued supply of raw materials at the best price to the consumer with sufficient profit to the producer. Today, geological insurance safeguards capital investment in plant and assures economical development plans.

Jan 1, 1978

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

By P Sutton

The global goal of Sustainable Development is not achievable without major changes in the way goods and services are delivered and material needs are satisfied, which requires tremendous innovation in the supply chains and life cycles in which minerals and energy processing take part. Values derived from minerals and metals processing need to be delivered with a fraction of current ecological impacts, which means removing technical obstacles to eliminating waste and emissions in the minerals cycle. The challenge is to find economically attractive ways to get there, through eco-efficiency gains in existing operations, capturing regional synergies, streamlining and greening the materials supply chain, and commercialising new process technology and new products. This paper summarises the outcomes of the Sustainable Resource Processing project, which was designed to provide a strategic analysis of what sustainability means for minerals and metals processing and how that can be effectively translated into technical and business innovation.

Jan 1, 2002

The various risk components to be addressed by explorers and project developers (and their investors) to minimise and/or manage the risk of Pacrim mineral investment are summarised to provide an overview of the issues involved and to set the scene. It then highlights the role of individual Mineral Industry Professionals (especially independent consultants) who are at the heart of any risk reduction or risk management strategy. The involvement of accredited qualified/experienced (competent) and reputable professionals is essential to produce realistic and reliable results that gain and maintain investor confidence. Today, high ethical standards as well as technical competence are sought by government legislation/licensing regimes and initiatives of professional bodies like AusIMM, MICA, Professions Australia, Council of Professions, etc. All attempt to regulate and guarantee reputable individual professional behaviour (particularly in the context of currently perceived high corruption levels in many Pacrim countries). Brief comment will discuss the usefulness of accreditation and ethics codes plus other specific codes (eg JORC/VALMIN and their international analogues in Canada, South Africa, etc) in reducing risks.

Jan 1, 2004

"DEEPHOLE " or "Longhole" drilling is the name given to the drilling of prospecting holes with the pneumatic hammer drill. The drilling bit is of the same form, and is prepared in the same way as ordinary rock drill steel, and is extended to the bottom of the hole by sectional hollow rods, through which water is forced.The cuttings from the hole provide a sample of the ground drilled.Deephole drilling was developed at an American mine where the cost of diamond drilling, owing to loss of diamonds, was excessive, and proved very successful, holes being drilled as deep as 220 ft., in limestone, at a cost of one dollar per foot. The use of the method in other mines, and in a variety of rocks, has since been described in the technical literature. From the published descriptions the following data are drawn:

Jan 1, 1930

A sample of tailings from a local, low grade (less than 2g/t) tailings dump was investigated for gold recovery. The tailings were very fine, with 90 per cent passing 30¦m and almost 60 per cent passing 10¦m. Tabling the coarse product from classification using a cyclone proved unsuccessful, with low recoveries being obtained due to high gold losses in the slime streams. Gold recovery by cyanide leaching was quite rapid, with recoveries of 85-90% being obtained in five hours. Lime and cyanide consumptions were 3 g/t and 0.1 kg/t respectively. Gold loading onto carbon was inhbited by the presence of the large amount of fines, so heap and vat leaching should be considered where the gold is recovered from a clear pregnant solution. Settling tests were conducted on tailings. It was observed that the addition of at least 3 kg/t lime or 0.4 kgh nonionic flocculant was necessary to promote settling of the tailings to generate a clear supernatant for gold and water recovery.

Jan 1, 1991

By E Hogan, M Goodz, R Wright

The planning, permitting and monitoring procedures of the re-opening and rehabilitation of mine sites is an ongoing process which must continue throughout and beyond the life of the project. Both industry and government bodies must remain flexible to allow guidelines to be altered where and when necessary.To enable the successful re-opening of the Morning Star mine at Woods Point in alpine Victoria, many environmental and historical issues had to be evaluated.The site which had been derelict for 28 years had to be rehabilitated to a safe and aesthetically pleasing state prior to construction of a new operating mine site. Considerable liaison with government authorities and the local community was required.

Jan 1, 1992

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984

By Lynn DR, Wadley GB

The Australian gold industry has made large steps forward in the last few years. This progress has been driven by improvements in mining and processing technology, the high price of gold and by a favourable legislative, political and taxation environment. This paper concentrates on improvements in gold project development, process engineering and technology as seen by BHP Engineering, Perth, Australia.The paper describes technical aspects of successful gold project development including metallurgical testwork, feasibility studies, choice of process flowsheet (gravity, heap leach, carbon in pulp (CIP), carbon in leach (CIL) or other routes). It sets out our views on plant design, plant construction, procurement and project management.A case study for a small plant recently completed in the Philippines is presented as a solution to the problems often encountered in treating quartz vein gold deposits.

Jan 1, 1990

The amount of land subjected to coal surface mining in the United States has been reported at 1, 302, 000 acres (1). Latest National Coal Association estimates (1968) show that about 65, 000 acres are affected annually in the production of 186, 000, 000 tons of coal. Peabody Coal Company affects approximately 9500 acres annually in the ten States in which we are presently operating. Surface mining at Moura, Australia was begun in February 1961. In Marcy 1963, the Marion 7900 dragline with 35 cubic yard bucket went into operation and in 1967 the Marion 8900 dragline with a bucket capacity of 130 cubic yards was put into operation. In addition a third dragline, a 480W was added in 1969. It carries a 15 cubic yard bucket and is used to work areas that are too small to justify movement of the larger machines, In 1969 the Moura surface mine produced 3, 002, 774 short tons, and in 1970 3, 418, 933 short tons.

Jan 1, 1971

By A Kyllo a, D R. Swinbourne

Electric arc furnace (EAF) dusts contain significant quantities of zinc, found almost entirely as either zinc oxide or zinc ferrite. The dust has been classified as a hazardous waste due to the relative high lead, cadmium and hexavalent chromium contents. It is important that environmentally acceptable processes be developed to treat this waste. One possible process involves reacting the zinc compounds in the dust with metallic iron, thus avoiding zinc vapour reoxidation by CO2 as occurs in carbon reduction processes. It consists of two stages where the first is the reduction of iron oxides to iron and the second the reduction of zinc oxide to zinc vapour by the iron. In this work the effects of operating variables such as temperature, CO/CO2 ratio and pressure on the recovery of zinc from an industrial EAF dust obtained from the Smorgon Steel Mill were investigated. Zinc recoveries in the second stage were found to approach 100 per cent at 1000oC after about four hours in nitrogen but within 40 minutes if a low vacuum was used.

Jan 1, 2000

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

Since 1960, the Dongchuan Copper Mining Bureau, Yunnan Province, China, has treated copper oxidised ores by sulphidisation - flotation technique only to recover copper. In order to improve the metallurgical performances and economics of flotation, extensive development work has been carried out during the past 30 years: several specific flotation flowsheets have evolved from the originally selected `stage - grinding and stage - flotation' flowsheet to suit various ores; the overall grinding size of the ores has been increased from 80 per cent - 200 mesh to 90 per cent - 200 mesh, resulting in significant increase in copper recovery; the substitution of CaS for NazS proved to be successful in sulphidisation of copper oxidised minerals, and also in avoiding the depressing effect of Na2S on copper sulphide minerals; the application of a number of activators of copper oxidised minerals, especially ethylene diamine phosphate, has considerably improved the flotation performance and decreased the consumptions of other reagents. Finally, the combined use of sodium hydroximate with butyl xanthate has been shown to be effective in enhancing the floatability of both copper oxidised and sulphide minerals.

Jan 1, 1993

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. Strong outbursts often have occurred in geological tectonic zones and concentrated stress areas. There are some particular characteristics of these strong outbursts, including the effects of ground stress, gas pressure and the properties of coal associated with the outbursts.

Jan 1, 1986

By Fewings JH

When the mining and milling of 1100 Copper Orebody commenced, difficulties were experienced in producing a satisfactory grade of copper concentrate. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 Orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in an inherently flotable fine pyrite and silica fraction. The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to'the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1970