Search Documents

By P Mason, J F. Huntington, K M. Scott

Short-wave infrared (SWIR) spectral reflectance of the hydrothermally altered volcanic rocks in the footwall of the Hellyer Zn-Pb massive sulfide deposit was measured with a portable PIMATM infrared spectrometer. The Al-OH absorption band was used to derive information on the cation composition of white mica. The wavelength range of the Al-OH band from 2194 nm to 2222 nm reflects variation in the number of octahedral Al (Alvi) in white mica from 3.9 to 3.2 (based on four octahedral cations per formula). This Alvi range indicates a substantial compositional variation, covering most of the compositional region between muscovite (Alvi = 4.0) and phengite (Alvi = 3.0). Moreover, the spectral reflectance data show that the compositional variations of white mica are spatially related to the hydrothermal alteration zoning, such that the white mica of more phengitic composition tends to form in the main upflow fluid channels in the centre of the footwall alteration system. The results suggest that the octahedral Al content of white mica, which is spectrally definable by the wavelength of the Al-OH band using a field instrument such as the PIMATM, can be used to map fossil hydrothermal systems and potentially as vectors to mineralisation.

Jan 1, 2004

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By M F. Navarrete

During 2003, different plastic stemming plugs (Cats«, Stemtite«, and Taponex«) were tested in EscondidaÆs Mina Sur, to determine the effect on gas retention time when used in conjunction with drill cuttings in production shots with a blasthole diameter of 10 5/8ö. Longer retention times were expected to provide greater fragmentation and muckpile looseness. In order to determine which plug showed the greatest enhancement of stemming retention, 17 trials were carried out û in the first seven tests, only the Cats were used, in the following five tests, a combination of Cats, Taponex and Stemtite were used, and in the last three tests, only the Taponex plug was used. In the last two blasts, drill cuttings were used without stemming plugs as a benchmarking exercise. Blasts were filmed with a high-speed camera, which could record the detonation times of holes using rolls of shock tube tied to stakes at the hole collars, to act as flash indicators. The camera allowed measurement of the time between charge detonation and the commencement of stemming ejection. In order to obtain the statistical parameters of each one of the stemming plugs used in the 17 trials carried out, the Minitab software was used and a data base was created for it, corresponding to each stemming configuration with the retention time obtained from the filming. Once it was determined which stemming plug provided the greatest enhancement of stemming retention, the impact on the fragmentation was analysed using the WipFrag image analysis software to estimate the muckpile size distribution.

Jan 1, 2004

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

By Firkin GR, Allen RJ

Sulphide Corporation Pty. Limited has roasted a number of different zinc sulphide concentrates on its sinter machine which pro- duces zinc-lead sinter for an Imperial Smelting Furnace, and results have varied widely. The differences are considered to be functions of !concentrate particle size and reactivity. Amdel have used differential thermal analysis to examine these concentrates and two major effects have been found. Firstly, in concentrates 1containing small quantities of pyrite and chal- L [copyrite, heat is liberated at 400¦C to 650¦C [by oxidation of these two sulphides. Secondly, as particle size decreases, heat release from the oxidation of zinc sulphide commences at flower temperatures and rate of heat release In a sinter bed, the presence of some rite and chalcopyrite would help to heat the cc sulphide to ignition temperature in a orter time, while a finer concentrate would sult in roasting being completed more ickly. Both of these effects result in a arper flame front and minimise the chance heat and combustion fronts being mismatched. is theory is supported by sintering results tained by Sulphide Corporation. As a result

Jan 1, 1975

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

By Wagland D. G, Guo H

The Mt Whaleback orebody is in a complex geological regime. A good understanding of geological structure is essential during the design and implementation stages. The amount of information on the rock-mass condition available at the design stage is considerably limited. It is essential to validate the rock-mass properties used in the design during implementation. It is important to achieve integrity of the final pit wall during development and to maintain the integrity until the end of its designed life for safe and economical extraction of ore. The original geological model is updated by way of on-going detailed geological face mapping. Original design is reassessed and is modified based on any significant variations to the previously evaluated geotechnical conditions. Information gathered during design implementation provide tools for effective management of the pit walls. Controlled blasting techniques are employed in the final limits blasting. Presplit blasting is used in most limits blasts. Presplit helps to maintain the integrity of the wall by venting excessive gases from the limits blast. This helps to reduce bedding dilation by gas penetration. Also, it helps to define the design batter for the operators for final batter trimming. Pyritic shale needs special attention during blasting due to its reacting nature. Cablebolting is applied in selective areas to secure small-scale potential instabilities. During the development phase, pit wall monitoring instruments are installed. These instruments are used to monitor the performance of the wall during and after excavation of the slope.

Jan 1, 1995

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

The procedure used for Truck Maintenance is described systematically in this paper. Emphasis is given to manpower required, work facilities, daily maintenance and oil sampling procedure. Scheduled Preventative Maintenance Service, Electrical Service, Component Change, Truck Overhaul and Outside Contractors are also discussed. The system used, achieves the required results with an average haul truck availability in 1981 of 87.9 per cent. INTRODUCTION Situated on the Island of Bougainville, in Papua New Guinea, the Bougainville Copper mine nestles in a valley near the crest of the Crown Prince Range, between 600 m and 980 m above sea level. The mine is serviced by two towns, Arawa - an open town on the Coast and Panguna at the Mine Site. Currently Bougainville Copper operates an open pit mine removing an average of 198 000 dry metric tonnes of material per day (115 000 tonnes ore and 83 000 tonnes of waste) with a fleet of electric shovels and 154 tonne electric haul trucks.

Jan 1, 1982

By N C. Steenkamp

The Northern Cape Province of South Africa is host to the Kalahari Manganese Field (KMF). The northern portion of the KMF hosts high-grade manganese referred to as Wessels’ type ore and is mined mostly from underground operations. WorleyParsons TWP is currently involved with the development of a ventilation shaft for one of these mines. The main challenge is to develop through the unconsolidated Kalahari material and weathered portion of the Karoo formation. These formations are preserved very erratically over short distances. A lack of understanding of the unique challenges presented for developing shafts in this area has resulted in the failed development of a shaft on an adjacent property and over-expended budgets on others.The renowned red sand of the Kalahari forms the top several tens of metres and overlies a horizon of gravels and calcrete that pose seasonally variable water ingress problems. A very stiff red clay horizon is then intersected. The Red Clay is prone to swellling during excavation and has been the main stumbling block on previous constructions. The standard approach has been to develop non-stop through this layer. The red clay is underlain by another horizon of calcrete, gravel and conglomerate that marks the bottom of the formation. The top of the Dwyka Tillite (Karoo Formation) is usually highly weathered and has a distinctive yellow colour. The weathered tillite is highly susceptible to drying and becomes friable. At reef-intersection, the combination of subhorizontal bedding and joints with the dominant subvertical faulting results in potential wedge failures in the manganese and ironstone units.This paper describes the geotechnical issues identified during the planning of the ventilation shaft and the risks associated with development through the Kalahari and weathered Karoo Formations. A new approach to developing ventilation shafts in overcoming these challenges is recommended.CITATION:Steenkamp, N C, 2014. Challenges of developing a ventilation shaft in Kalahari and Karoo formations, Northern Cape, South Africa, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 81–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Blake W

Based on preliminary computer model simulations and stability analyses, both longi- tudinal and transverse, large dimension, cut- and-fill rooms were designed for the parallel dipping ore layers at Kamoto mine. Full scale testing of the designed rooms showed that the rooms are stable and that the rock behavior is predictable. Ordinary waste rock was selected as the filling material because the fill was found to carry little load.

Jan 1, 1973

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

In the mid-1990s, after a long period of antipathy between the company and its detractors, Rio Tinto embarked upon an ambitious cultural change program that sought to transform the fundamental basis of its relationship with global, national and local stakeholders. This has evolved into a broader pursuit of positive cultural change within Rio Tinto as part of the mining industryÆs Sustainable Development initiative. Initially driven from the top down, the communities component of this program comprises an architecture of policies, value statements, social research and verification systems. The commitment to better community relationships is best exemplified in Australia by the scope and scale of the GroupÆs Aboriginal land access agreements, community development programs and the work of the Rio Tinto Aboriginal Foundation. While collectively these form the core elements of an evolving set of internal social competencies, development of second-tier competencies is required to organically embed a culture of sustainable relationships with local and regional communities. Second-tier competencies will include appreciation of social dynamics, social science and diversity at middle management level; rigorous social research that properly informs development options for companies and host communities; career paths and recognition within the mining industry for young professionals both generally and from stakeholder communities; proper community-needs assessments, research into such things as purchasing power and other economics data, and inventories of public goods such as land-carrying capacity and water availability. Without this information it is difficult to gain an appreciation of and to alert people to the consequences of change brought on by a mine. The next decade will see second-tier social competencies promoted within successful mining companies. Measures to achieve this include a range of Human Resource (HR) incentives such as recruitment and career advancement based on broad competencies rather than narrow technical proficiency, humanities training for mining professionals and performance rewards that recognise social competence. A sustainable future for mining in a globally connected social landscape requires selection of people who can listen, relate and act in an open social system. The challenge for the mining industry, its professional organisations and educational institutions is to acknowledge this and develop these new aspects of mining industry professionalism. This cannot be left to individual companies if the industry is to have a sustainable future.

Jan 1, 2002

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

The Mt Leyshon Gold Mine is located 30 kilometres south of Charters Towers in Northern Queensland. The current open cut mine has been in operation since 1986. In 1992 a feasibility study was completed that recommended an increase in production to over 240 000 ounces of gold per year. This proposal required an upgrade of the processing plant to five million tonnes per year, and an enlarged mining fleet to provide additional ore, and to meet the increased waste removal requirements. The implementation of the mine expansion program during 1993 required the Life of Mine plan to be extensively revised. This required the assessment and management of potential risks associated with the mine design. The updated geological model using the 1992 drilling results along with the actual contract mining and processing costs were used to establish a series of nested optimised pit shells. The total and incremental quantities and costs were then analysed to determine a suitable pit perimeter. The pit and phase plans were then created and used to devise a staged development plan. The block layout plans for each bench were then established from which a detailed life of mine production schedule was created.

Jan 1, 1994

By Lu S, Zhou S

The flash smelting technology employed in Jinchuan demands a better mineral processing concentrate with an MgO content below 6.5 per cent. Two ways for MgO removal have been investigated in detail based on properties and process mineralogical characteristics of the rich ores in the number one mining area in Jinchuan. The key to the first way is the use of a new flowsheet which has two-stage grinding and separation followed by single-stage regrinding and multi-stage cleaning for the rougher concentrate. The second approach utilises two novel reagents, AT-131 and AT-202, which have been developed recently. Excellent metallurgical performance has been obtained in a commercial test and a batch test, respectively. The MgO content of flotation concentrate can be reduced to about six per cent.

Jan 1, 1996

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992