Search Documents

By P Bonniwell

As a part of the Newcrest, Telfer Expansion Project, a consortium of Australian, Canadian and South African Mining Contractors in joint venture have been contracted to develop the hoisting shaft. The parties namely; Byrnecut Mining Pty Ltd, Murray and Roberts RUC and Thyssen Mining Construction of Canada Ltd have combined their individual expertise to excavate the shaft. There is a particular emphasis on the use of proven shaft sinking techniques from North America and in particular integrating electric hydraulic drilling equipment and personnel from the Canadian Mining industry. The Telfer hoist shaft when completed will have a finished diameter of 7.1 metres and extend to a depth of 1170 metres below the collar. The shaft will be fully concrete lined and will later be equipped for hoisting ore from the Telfer deeps at a rate of five million tonnes per annum. The shaft when completed will be the largest shaft ever completed in Australia on a volumetric basis. This paper will examine the technical aspects of the shaft sink, as well as exploring the integration of personnel and equipment from the frozen prairies of Saskatchewan, Canada into an operation in the Great Sandy Desert of Western Australia. What are the spin-off benefits for the development of other shafts within Australia?

Jan 1, 2005

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

By Flann R. C

A small modification to current industrial practice should lead to better nickel powders for use in alloying, electroplating, and powder metallurgy. Nickel powder compacts sold for alloying are not always suitable for electroplating applications, since some presently used commercial powders will expand on sintering. Further, such nickel powders are unsuitable for use in the production of powder metal parts, because of expansion during heating of the near-net-shape preforms. Research in these laboratories has enabled the elimination of expansion, and led to techniques for the production of compacts suitable, in particular, for commercial use in both alloying and electroplating. The techniques include: powder pretreatment, cold pressing and sintering, hot pressing, and hot pressing and sintering. In this way compacts are readily prepared with densities of at least 93 per cent of solid nickel, and these, when used as anodes in Watts general purpose and bright baths, give both cathode current and plating efficiencies of 90-98 per cent.

Jan 1, 1979

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

By Browne TJ

On 13 October 1993, a shallow earthquake registering 7.1 on the Richter Scale occurred near Tauta in the Finisterre Range of Papua New Guinea (PNG) killing 37 people. The aftershock series lasted three months and resulted in considerable landslide damage that destroyed villages, food gardens and airstrips, and blocked rivers causing catastrophic flooding. These effects have irrevocably altered the form of many of the valleys and rivers draining into the Markham and Ramu valleys.The earthquake occurred in a pilot study area for a landslide hazard mapping project being carried out by the PNG Geological Survey that commen-ced in April 1993. Comparisons made between areas identified as unstable during the study with those damaged by the earthquakes show good correlation.It is concluded that aerial photograph and Landsat TM imagery interpretation can be used with a high degree of confidence to identify potential landslide hazards in mount-ainous terrain. Landslide hazard maps are promoted as a tool for use in the route planning of roads and powerline corridors, as well as for identifying vulnerable communities.

Jan 1, 1994

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

My forebears migrated to South Australia in the 1830s, 1840s and 1850s. All of them were literate but, because they moved about South Australia looking for work, family papers have become scat- tered and I am left with a few fragments. Some years ago I was intrigued to find among my fath- er's books a frontispiece in an old Anglican Book of Lessons. As can be seen Joseph, a mining smith, was also a Freemason. Thus my interest was aroused. I know some- thing of modern day mining communities in South Australia and wondered what they were like 100 or more years ago.

Jan 1, 1987

An integrated computer system (the Short Term Mine Management System) has recently been developed by B.H.P. Steel Long Products Division in Whyalla, South Australia for use in their open pit iron ore mines.The system incorporates blast design, comprehensive blasthole data handling, grade coilrol, stockpile scheduling and management and reconciliation within a single, user friendly computer package. The blast design system allows the blasting engineer to design the layout of holes for a production blast using geological information projected from the bench above to aid in appropriate blasthole positioniog in particular rock types. The grade control system allows mining blocks to be designed and evaluated from blasthole information using interactive graphics processes. The handling, storage and reporting of blasthole survey, assay and geological logging data forms an integral part of this system. Stockpiles can be constructed from a number of mining blocks to reach a specified target grade using the stockpile management system. Although not yet integrated, the reconciliation system will reconcile stockpiles back to mining blocks and to the geological model.

Jan 1, 1990

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

A new gold cyanidation assay technique has been proven for a range of ores, where it has demonstrated benefits of being: ò Accurate (reduces the typical range of assay scatter almost three-fold, and avoids common fire assay interferences). ò Fast (under one hour, providing a quantum shift in space requirement and equipment utilisation each bottle roll can provide over 15 determinations per day). ò Simple (suitable for field application, no high skill or experience requirements). ò Profitable (reduced drilling, drilling time, ore misclassification and/or double handling after mining). ò Cheap (far lower cost than Fire or Aqua Regia Assays, ie LeachWELLTM costs around 10ó for a 20 g sample at 50 per cent solids, proportionately greater for larger samples eg $1 for 200 g samples which address most nugget effect problems). ò Relevant (distinguishes economic. ie cyanide-extractable gold, the only unequivocal value to use for true resource definition, mine planning and grade control). ò Robust (rough bucket chemistry of samplers does not seriously affect results). A new development is the provision of LeachWELLTM CAS, a solution, which also contains optimum cyanide and stabiliser concentrations; and offers greater: ò Safety (the dilute cyanide solutions are stabilised to avoid generating toxic HCN vapours; and present no cyanide dust or flying chips to deal with). ò Ease (a single squirt dispenses precise quantities of the entire reagent suite, avoiding multiple weighings). ò Reduction in total reagent costs. An inter-laboratory comparison on nine ore types, using two assay techniques (Fire Assay and Aqua Regia) involving 45 laboratories, has demonstrated that LeachWELLTM 60X assays for the samples tested, were equally or more reliable than typical Fire or Aqua Regia Assays. There is particularly great benefit in applying LeachWELLTM 60X assays to richer ores in comparison to Aqua Regia assays, which appear to be prone to very significant underassaying depending on individual analyst skills, and which often suffer greater nugget effects. The major impacts for heap leaching are that: ò Using the LeachWELLTM assay technique for grade control, ore of marginal grade is not accidentally discarded to waste or visa versa due to the scatter of assay data inherent in typical small charge (25 g) fire assays. ò LeachWELLTM assays very importantly report only that gold which will be recoverable in the heap, viz that which is liberated - an important factor where the coarse crush often leaves ten per cent of gold unliberated. These impacts are of particular importance for many ores (ie most of those recovered from open pit operations and at the margins of rich ore subject to slurry processing) subjected to heap leaching as the oxide zones often present major problems of nugget effects as well as mineralisation that cannot be accurately assigned through interpretation of clear structural controls.

Jan 1, 1994

By P Jago

KCGMÆs Fimiston Open Pit, located in the centre of the historic Golden Mile, is situated above some 3000 kilometres of old underground workings. These workings, both level and vertical, present significant safety and operational problems in the pit. One of these challenges is in safely drilling void areas so that they can be charged and blasted effectively. Current drilling practices in these areas require machines that can only drill 115 mm holes on a smaller pattern than the standard blast pattern. This results in more time and cost to both drill and charge these areas. Any other method currently available to drill out these areas involves putting operators in a potentially hazardous situation by being too close to the void area being drilled. Not effectively drilling and blasting these areas leads to hazardous situations further in the mining cycle including oversize, large toe and uncollapsed voids. Ineffective blasting also causes reductions in mining productivity and mine to mill performance. In response to these issues, KCGM has commissioned the implementation of a fully remote controlled DM45 blast hole drill rig to drill out selected void areas. The remote system, installed in conjunction with Ausdrill Ltd and GM Mining Electrics, is designed to operate similarly to a tele-remote bogging system with the operator controlling the drill rig from a separate control cabin via radio signals and video feed. This allows KCGM to drill in areas of higher risk without exposing the operators to voids. The drill rig will also be able to drill standard patterns through some specially selected void areas, reducing costs and extra time associated with drilling and charging void affected areas. The remote rig is expected to provide a number of benefits, both in the drilling process and in further downstream operations. Costs of drilling in void areas are expected to decrease with standard patterns instead of smaller patterns being drilled. Safety and operator comfort are also expected to increase through removing the operator from the pit floor. Blasting is also expected to see significant improvements through increased ease of charging void areas (because of larger holes and standard patterns), more consistent patterns resulting in less secondary blasting and toe and an overall improvement in the speed and cost of charge-up practices. This more consistent blasting will also improve shovel productivity, crusher performance and overall mine-to-mill efficiency. This paper presents an overview of the development of the remote controlled system, including modifications that have occurred since commissioning. It explains some of the problems encountered and how these have been solved. Key issues for operational success will be identified and explained with a view to making future implementations easier. Factors used to assess the performance of the remote controlled rig will also be explained in further detail and used in a preliminary assessment of the rigÆs feasibility.

Jan 1, 2003

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By Brown GA

Results are presented which demonstrate the feasibility of employing electrolytic membrane technology to process leach liquors derived from alkaline pressure leaching of scheelite concentrates and to recover and recyle sodium carbonate. Thus the problem of disposal of sodium sulphate is avoided. In a further application of the technique sodium tungstate is converted to tungstic acid which can be further processed by three possible routes to crystalline or amorphous tungstic acid or tungsten powder. In each route sodium hydroxide is produced which on carbonation can be recycled as soda ash to the pressure leach stage. Further testwork is required to determine long term operational conditions in the membrane cell and to confirm the effect and deportment of impurities on products. The process has been patented.

Jan 1, 1986

By T Roache, K Yang, M Quigley, C Young

In late 2004 a large-scale evaluation of a new suite of tools for semi-automated core logging was carried out in the Eastern Goldfields of Western Australia. Known as HyLoggingÖ Systems, these combine rapid hyperspectral mapping of mineralogy and very high resolution digital imaging of cores and chips in their original containers. The resulting data is very information-rich and provides information about host rock, alteration and regolith mineralogy. This, in turn, can be used to test geological models about fluid/rock interactions, ore system architecture, ore feed characterisation and generally improve the objectivity of the normally manual and variable logging process. Results were obtained from the Kanowna Belle and St Ives gold deposits in the Kalgoorlie region, as well as numerous holes from across Western Australia stored in the Kalgoorlie Core Library. At the Kanowna Belle gold deposit critical spatial trends in the proportions of white mica, the chemistry and species of those micas, the presence of selected carbonate species and the absence of chlorite proximal to ore zones have all contributed to improved ore deposit understanding. Significantly many of these trends are not discernible to the naked eye, nor easily quantified, previously, across many thousands of metres of core from separate drill holes. At St Ives, the HyLoggerÖ was able to show that low-Al (phengite) and high-Al (paragonite to muscovite) white micas are spatially associated with D3 foliation zones that are proximal and distal to Au mineralisation, respectively. D3 foliation zones are also associated with the depletion of metamorphic chlorite and amphibole, and their replacement with biotite, relative to unaltered mafic host-rocks. The HyLogged GSWA drill holes yielded mineralogical characterisation of classic deposits, including Kambalda (Ni), Fimiston (Au), Teutonic Bore (Cu, Zn, Ag), Black Swan (Ni) and Hannans (Au), illustrating a wide variety of mineralogical trends due to both host lithologies, previously unrecorded lithological subdivisions, and alteration patterns. During 2005 a unique thermal infrared HyLogger was developed to map the important remaining silicates, such as feldspars, quartz, olivines, pyroxenes and garnets. This was successfully tested on a 9000 m subset of the same cores as the earlier study. Interpretation has focused, in particular, on silicification, albitisation, and the mineralogy of several high-grade, less hydrous deposits.

Jan 1, 2006

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993

Filter aids are currently used in many industries to increase filtrate clarity and filtration rates. In other industries filtration could be improved if accept- able filter aids could be obtained cheaply. The present paper describes a simple thermal process for making filter aids from coal, outlines the effects of coal properties and major operating variables, and discusses the properties of satisfactory products. Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization. The limits imposed on product yields by the composition of the parent coal are considered in relation to a range of Australian coals and one New Zealand coal; and the effects of temperature, residence time, and reactant flow rates have been studied in relation to product yields and characteristics.

Jan 1, 1969

By Moore J

Gunpowder Copper Ltd is using in-situ leaching to extract copper from the Mammoth sulphide ore deposit in north-west Queensland. To increase metal recovery, ore is fragmented using conventional underground longhole drilling and blasting techniques. Although the upper levels of the orebody had previously been mined by open cut and underground methods, significant reserves of copper existed around old workings. To safely and economically recover this resource, a decision was made to fire the remaining pillars in the upper part of the mine by a single 1.37 million tonne mass blast in February 1992.This paper records the planning, design, and implementation of the Mammoth mass blast. Geological and geotechnical aspects are summarised, to explain the reasons for such a large blast. Drilling, charging and blast initiation are discussed in detail, to show how standard equipment and products were applied to a unique task.

Jan 1, 1992

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990