Search Documents

By Follington I. L

Various methods for stress measurement in the coal industry are briefly reviewed. Methods for presenting and interpretation of measured stress and displacement data are discussed with a view to assessing the mechanisms of failure. Arguments are presented for reviewing the current practices in this regard with reference to coal pillar and strata stability analyses.

Jan 1, 1991

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

To the layman or the casual in- vestor, the critical problems in the mining industry appear to rest on the questions of finding and developing an orebody. The high cost of finding a major orebody suggests that the search is the only matter of real concern. However, the resulting operations which hopefully will provide a profit- able return, depend very heavily on the quality of the servicing that the particular industry receives. Once the mining venture has been established with the necessary plant, equipment and infrastructure, the routine servicing becomes an important function of the operations.

Jan 1, 1975

By Dorricott M. G, McAllister J

This paper is concerned with the application of a probabilistic approach to the risk assessment of mining projects.In current practice, sensitivity analysis is the most commonly used deterministic approach of accounting for the uncertainties involved in mining project evaluation, while Monte Carlo simulation is considered to be the best probabilistic method available for the same purpose. The methodology of the approach proposed in this paper is as simple as that of sensitivity analysis. However, the results obtained can be more comprehensive than those obtained from Monte Carlo simulation. Various important statistical features, such as correlation and skewness, of the basic random parameters can be easily taken into account by the proposed approach. Example studies are demonstrated. Lotus 123 was employed for the associated probabilistic calculations.

Jan 1, 1992

As the worldÆs population and global standard of living increase, the role of metals in the economy will not diminish in the 21st century, despite substitution and dematerialisation trends. Industrial Ecology is an emerging science that attempts to bring together physical, biological and social scientists and develop the tools for good management of the planet in the long run. In engineering terms, Industrial Ecology is defined as the reconfiguring of industrial activities with full knowledge of their environmental consequences. Production and use of materials must take into account the needs of both market and environment. Dispersive uses of metals will be phased out, as is being done with lead in gasoline, and post-use recovery of materials and energy will increase. This will result in an advantage for metallurgical processes that can use as feed materials concentrates as well as metal scrap and waste streams, such as bath smelting processes and slag resistance electric furnaces. The paper also discusses how metal extraction technologies, developed in the 20th century to provide essential materials to humanity, can be applied for the benefit of both mankind and environment in the 21st century.

Jan 1, 2000

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By McLaughlin R. G, Brammer R. A J

King Island Scheelite had been using dealer modified front end loaders for two years when in 1974 it started to increase production. Suppliers were then quoting long deliveries for underground diesel trackless mining equip- ment, and the Company was forced to modify surface machines which had become redundant as production from the open cut phased out. The results were generally successful and encouraged further adaptations. Drill jumbos excepted, the Company now uses only converted surface machines in areas worked by diesel engined equipment and for all support and auxiliary functions.

Jan 1, 1977

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

The excavation of sandstone of generally medium strength for the Liverpool Link Line by Dosco Mark 2A Roadheaders has demonstrated the versatility and good performance of road- headers in suitable rock formations. A description is given of the strata traversed by the tunnels together with descriptions of equipment and crews, excavation sequences, operating difficulties and the results achiev- ed. In addition tunnel construction is des- cribed for a difficult section where there was only O.Sm clearance between invert and a four lane vehicular tunnel below, and O.5m clearance between tunnel crown and a century old sewer above.

Jan 1, 1976

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963

The high maintenance of load-haul-dumps (LHDs) and front end loaders in hard rock affects mine planning with reduced availability and productivity. Intensive study of maintenance costs and availability of machines related to machine age and life provide the basis for planning from available operational alternatives.Derived programmes and experiences have led to the beginnings of unmanned operation and automation through reduction of manual diesel units and spreading electrification and use of radio. But electrification has obvious layout limitations. This approach to the present has resulted in better utilisation, costs and safety and the computerised monitoring and control provides continuous awareness of machine and work conditions with the promise of future improvements.

Jan 1, 1991

The Hail Creek coking coal deposits are situated in Central Queensland, inland from the port of Mackay. A joint venture of Australian and Japanese companies has been formed to examine the feasibility of developing these deposits for sale on the overseas markets. The project envisaged involves large scale mining operations and on site benefic- iation to wash the coal to marketable quality. Infrastructure items include a 140 kilometre railway to the coast, a port facility, and at Ilail Creek, power and water supplies, roads and communications, and accommodation for a substantial workforce. The need for town development and the responsibility for the development are established. The town planning implications of coal production at the rate of five million long tons of washed coal per annum from open cut and underground mines are considered. A procedure for estimating the size of the town is expounded and the town size is determined. The factors influencing site selection are explained and a site is suggested. A method of designing the town is described and comments are made on developmental aspects. Spaciousness and preservation featuring the natural environment will be the theme of the town development.

Jan 1, 1973

By Cooper P. G

I he Electrolytic Refining and Smelting Company (ER&S) has oper- ated a copper smelter at Port Kembla, NSW since 1908. The feasibility of modernising the smelter was recently studied and external influences were shown to have a substantial impact on the project economics. Profita- bility is determined by the relative magnitudes of treatment charge income earned from processing raw materials and the operating costs incurred. Treatment charges are usually denominated in U.S. dollars and are deter- mined by market forces in the world copper industry. ER&S is no different from other Australian manufacturing industries in that it must maintain its competitive position by controlling costs. The modernisation project seeks to achieve this through new technology and improved labour Productivity.

Jan 1, 1988

By Barnett J. C

The arid and semi-arid region of Western Australia occupies about two-thirds of the State equivalent to an area of about 1.8 million sqkm. Groundwater demand in this area has historically been linked to the pastoral andmining industries commencing with the gold discoveries in the Eastern Goldfields some 100 years ago. Substantial increases in demand have occurred in the past two decades initially as a result of nickel discoveriesin the early 1970's and more recently the rapid resurgence of the gold mining industry. Mineral exploration and development in the Great Sandy Desert at Telfer (gold) and Kintyre (uranium) and in the Great Victoria Desert at MulgaRocks (uranium) has also been accompanied by detailed groundwater investigations.

Jan 1, 1988

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

By Matsumura T, Takematsu T

The Brown Coal Liquefaction Process (BCL Process) has been developed by Nippon Brown Coal Liquefaction Co., Ltd. (NBCL), and a 50-ton-per -day Pilot Plant has been partially completed and put into operation by Brown Coal Liquefac- tion (Victoria) Pty., Ltd. (BCLV) at Morwell, Victoria, Australia. This Project has been sponsored by New Energy Development Organization (NEDO), an or- ganization associated with MITI, and has been promoted as a National Project with funding by the Japanese government. This project has also been conducted as a cooperative technology de- velopment project between the Japanese and Aus -tralian governments since 1980 and has been supported by the Victorian state government and

Jan 1, 1987

Western Australian tin deposits are similar to those of other Precam- brian terrains in that they are mainly associated with rare-metal pegmatites, in which cassiterite is found with minerals containing any or all of the elements Ta, Nb, Be, Li, Cs, Rb and the rare earths.. They differ from Phanerozoic deposits where cassiterite occurs in quartz veins, greisens, dis- seminations in granite or sulphide lodes, and is associated with minerals containing W, Mo, Bi, Sb, As, Ag, or Cu. The main tin production in Western Australia has come from the Pilbara Block where the more important tin- bearing pegmatites are related to a younger granite phase, and from Green- bushes where large albite pegmatites intrude ?Proterozoic metamorphic rocks. The more important tin deposits in the Pilbara Block, and those in the Halls Creek and Murchison Provinces, are related to granites which are richer in Si and K and poorer in Ca, Mg, Fe and Ti than 'average granite'. The tin granites tend to have higher than average contents of Sn, Rb and Li.

Jan 1, 1973

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990