Search Documents

By M G. Millad, M Zammit

The Kipoi Central (KPC) copper project is located in the Katanga Province in the Democratic Republic of the Congo and is presented here as an example of an operating mine where the Mineral Resource was initially estimated by uniform conditioning (UC) and subsequently updated to localised uniform conditioning (LUC). This paper discusses the implementation of an estimate run using LUC and compares the results based on resource definition drilling to those obtained by close spaced grade control drilling and actual mill production.UC is a nonlinear geostatistical technique designed for recoverable resource estimation, typically using wide spaced exploration and resource definition drilling. The primary output of UC is the grade, tonnage and metal above a series of user-defined cut-off grades for a particular selective mining unit (SMU) block size. The UC approach is considered to provide a more accurate representation of the recoverable grade and tonnage at SMU support for non-zero grade cut-offs than would typically be achieved by a traditional linear estimator such as Ordinary Kriging. LUC is a relatively new approach involving the post-processing of a UC estimate and is used to spatially present the grade distribution predicted by UC at the SMU scale.This study demonstrates that the calculation of a more accurate and realistic grade-tonnage relationship for small SMU sized blocks is possible at the exploration stage using LUC, provided that the necessary theoretical and practical conditions for implementation of this technique exist.CITATION:Millad, M G and Zammit, M, 2014. Implementation of localised uniform conditioning for recoverable resource estimation at the Kipoi Copper Project, Democratic Republic of the Congo, in Proceedings Ninth International Mining Geology Conference 2014 , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By A D. Wulfse, C M. D Barton

Underground fractured aquifers in the Ernest Henry deposit are to a large extent controlled by deposit scale brittle structures. The underground mine has been subdivided into nine water zones based on hydrogeological characteristics, including conductivity and connectivity, within the mining areas bound by these structures. The nine water zones and the hydrological characteristics of the associated structures are utilised for risk assessing mine development and for targeting diamond drilling dewatering activities. Wireline and conventional underground diamond drilling techniques have been used throughout the network of underground aquifers with the aim of dewatering areas within the mining footprint. These dewatering drilling campaigns have historically been highly successful at lowering aquifer water levels throughout the underground workings. As part of recent mine expansion activities, diamond drilling has intersected high pressure (>507 psi), high temperature (>50°C) and high flow water (>3 L/sec) in as yet unconstrained underground aquifers. Groundwater is typically conducted through rubble and clay rich faults, further hampering progression of drilling. Drilling through fractured aquifers at depth presents both mine planning as well as safety challenges. Recent drill holes have been delayed or abandoned when aquifers hosting this high pressure, high flow water have been intersected, risking mine planning deadlines. Recent technological innovation developed to control groundwater outflows from the diamond drill hole whilst drilling has been trialled at the Ernest Henry Mine. This case study focuses on the utilisation of alternative drill methodologies to allow the current drilling campaign to continue without delay, whilst also improving safety conditions encountered on the drill site.

Mar 22, 2022

By Y-B Kang, W-Y Cha, Y-M Cho

Molten slag used in the secondary refining process (RH process) for the production of Ultra-Low C (ULC) steel is typically composed of CaO-Al2O3-MgOsat.-FetO with minor constituents. FetO in the RH slag is the main source of reoxidation of the molten ULC steel in the ladle by 2Al + 3(FetO) = (Al2O3) + 3Fe, thereby serving as the source of the alumina inclusions. On the other hand, FetO also enhances the fluidity of the slag, thereby increasing inclusion absorption capacity. Optimum slag chemistry design is therefore required to produce clear ULC steel. The reoxidation kinetics was investigated in the present study by employing high-temperature experiments and developing the reaction rate model. Initial compositions of slag ((% CaO)0/(% Al2O3)0 and (% FetO)0)) and reaction temperature were varied and change of [% Al] in the molten steel was measured. The rate-controlling step was analysed. It was found that the rate-controlling step in some cases changed during the reoxidation: from a mass transport of Al in the molten steel to a mixed transport including Al2O3 in the molten slag. The experimental data validated the reaction rate model based on the elucidated reaction mechanism and FactSage thermodynamic database. The model suggested that high (% CaO)0/(% Al2O3)0 suppresses the reoxidation only when (% FetO)0 is low (5 or lower in the present study).

Jun 19, 2024

By W Y. Kim, Y B. Kang, Y J. Park

The phase equilibria in the Al2O3–TiOx system were investigated in wide ranges of temperature and oxygen partial pressure: 1300~1600°C and 10-16.6~10-8 atm, respectively. The equilibrium phases and their compositions were identified using X-ray diffraction (XRD) and electron probe microanalysis (EPMA), respectively. Most noticeably, a wide range of pseudobrookite solid solution was found in equilibrium with almost pure alumina. At each temperature, the cationic ratio expressed as RTi = nTi/(nAl + nTi)) of the pseudobrookite solid solution showed a noteworthy dependency on the oxygen partial pressure. This resulted in the formation of a broad range of pseudobrookite solid solutions, ranging from Al2TiO5 (RTi = 1/3) to Ti3O5 (RTi = 1.0). Complete miscibility within the pseudobrookite solid solution was observed at 1600°C, with only a minor miscibility gap becoming evident below 1500°C. Based on the results obtained in the present study, the behaviours of Al2TiO5 pseudobrookite have implications in two key domains: (1) understanding changes in the physical properties of the materials, and (2) elucidating the evolution of Al–Ti complex oxide inclusions in liquid steel which can deteriorate the steel cleanliness.

Aug 21, 2024

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By C te Kloot, Z Liu

Blast performance and the resulting drawpoint condition and volume of oversize has the potential to impact operator safety and mine productivity. Underground measurements showed that approximately 14 per cent of production rings in the Ernest Henry Mine (EHM) sublevel caving (SLC) operation had either overbreak in the brow or left collars. There were also oversize rocks reporting to approximately 30 per cent of drawpoints, which accounted for over 7 per cent of total production and significantly impacted production rates. A series of trials were conducted in 2015–2016 at EHM to test changes to certain charge parameters in an attempt to optimise blasting results and, in particular, reduce oversize and overbreak. The detailed analysis conducted included field observations, hole surveying, blast monitor analysis and blast modelling. There were a total of nine charge parameters tested in the project, which fell into two major categories: energy distribution and inter-hole delay. These were based on observations made in establishing baseline data and those parameters most likely to have a significant impact on overbreak and oversize.Key results from the project included oversize reduction and improved brow conditions when energy distribution was reduced through changing charge lengths in certain holes in the standard charge plan. Similar benefits were also seen when the inter-hole delay between blastholes was reduced from 50 ms to 25 ms. Based on these results both changes were made to the standard production ring charge plan at EHM.Moving forward, the aim is to continue monitoring the results from the changes made on all levels to ensure efficiencies are being realised and sustained. A 3 per cent improvement in oversize as a percentage of total tonnes and improved brow conditions not only has a positive impact on production rates, but removes people from any potentially hazardous situations and contributes to a safer working environment.CITATION:te Kloot, C and Liu, Z, 2017. The evolution of production blasts at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 33–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By B L. Coulter, E Wightman, A S. Burrows

With their commitment to sustainable development in an increasingly carbon-constrained world, many resources companies are focused on reducing the energy required to create their final products. In particular, the comminution and smelting of metal-bearing ores are both highly energy-intensive processes. If resource companies can optimise the energy efficiency across these two processing stages, they can directly reduce their overall energy consumption per unit mass of metal produced and thus reduce their greenhouse gas footprint. Traditional grinding and flotation models seek to improve the efficiency of mineral processing, but they do not consider the energy used by downstream metal production, eg smelting and refining. Concentrators and smelters individually may be running efficiently, but are they optimising energy consumption of the overall system? A key step towards answering this question is to understand whether it takes less energy to remove an impurity in the concentrator or the smelter. Analysis of the complete concentrator û smelter process chain may show that there are times when the concentrator should use more energy to reduce the overall energy requirements across the mill and smelter. The new methodology discussed here will integrate downstream processing energy with mineral processing energy, to find the overall most energy efficient circuit design and operating strategy. The proposed methodology includes: determining what grade and recovery positions can be achieved in the concentrator by using different combinations and amounts of grinding and regrinding, thermodynamic calculations of the energy used to process the different concentrate grades to metal, and integrating the concentrating and smelting models to find the lowest total energy for the system. A case study which investigates the effect of increasing regrinding energy on the overall mineral processing û smelting energy consumption is presented. For the copper-nickel sulfide ore investigated the addition of regrinding results in 11 per cent less energy being used in the overall concentrator û smelter process chain per tonne of metal produced. Although regrinding is often seen as an energy-intensive process, in this case study the use of 1 kWh of energy for regrinding reduces the overall energy consumption by 12 kWh. The new mill to melt methodology will allow companies to model energy consumption from mill to smelter with a view to reducing the energy-intensity and greenhouse gas footprint of their processing and smelting operations.

Jan 1, 2009

By B Lance, D O’Brien

The Hidden Secret ore body is located within the Mt Charlotte underground mining system in Kalgoorlie, Western Australia. Mineralisation of the Hidden Secret ore body is lode style and therefore differs from the typical economical mineralisation mined at Mt Charlotte and consequently demanded a novel approach to the mining methodology. The ore body is lens like in shape, extending 200m along strike, 210m vertically, and dipping at 55 degrees. The lode width varies from 1.5m at the extremities to over 22m in the central zone of the ore body. Average grade is 3.4 Au grams per tonne. The initial mining methodology was Modified Avoca utilising Longhole Open Stoping with pillars, in a bottom up stoping sequence. However, as Hidden Secret became better defined and wider than initially modelled, it was identified that a high portion of gold would remain in the pillars and other mining concerns emerged such as remote backfilling large open voids and potentially unsafe vertical standoff distances between levels and wide open stopes. A re-evaluation of this method was undertaken and a new approach adapting a variation of Avoca methodology was identified to remove the rib pillars and replace them with a sill pillar separating the 4 levels into 2 distinct blocks. This new approach provided an immediate advantage by removing the bogger backfilling activity from the same level of the active stope front, enabling stope drilling and prepping to occur during the backfilling cycle. Bogging productivity has also improved as the fired ore is funnelled to the draw point by the backfill rill, significantly reducing the requirement for remote bogging thus improving bogging productivity. This mining method is currently in progress in the first of the two mining blocks and is on track to realise the targeted recovery of 7,700 ounces from the rib pillars.

Mar 15, 2021

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995