Search Documents

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

In attempting to vegetate pnob!em sites some basic pn.i,ne%ptes, namely the phys.ica.e and chemi.ca2 pnope/ti;es og the problem mateni.al and the selection oU hu.itab.2e p!antts {cor pnopagati.on, have to be considered. Pnobtem sites such as tai ing dams, mined-out atteas, and areas which have been genehaUy advehse2y a46eeted by mining activities, are not only o~ten located in a divehs.ity o4 climatic regions, but they also usuaUy dL64en substantially in theAjt .int' Lns c phys.ica2 and chem.i cat pnopen t i.es . To estabP.ish vegetation on such sites 6requent2y requites: .%) The ame Lonaton oU adverse {yaetors in onde t to exeate a hoot env.utonment suitable Uon "satis1actony" plant growth. .%i) These.2eationo4 plant species suited to the improved Hoot env.utonment, and eompat%b&e with the e2imate o{y the site, and the ultimate Land use o4 the site. iii) The estabL shment o{y a Laboratory and p-LLot scale testing programme to aeeomptizh the above.

Jan 1, 1976

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

Conditional simulation can be used to determine the probabilities of block iron-grades being above selected cut-offs. However, there are much faster alternatives that can produce acceptable results. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody is used as the basis of a case study to assess alternatives to simulation. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce data subsets. A complete distribution of iron grades for points or blocks is obtained utilising the data subsets and the following techniques: conditional simulation, median indicator kriging, the probability from conditional expectation and confidence intervals attached to the estimation of blocks in the framework of the discrete Gaussian model. The complete blasthole dataset is considered to represent the true iron grades at sample point support while the ordinary kriging estimate derived from these samples is considered to represent the true block grades. The distributions obtained from point estimates, block estimates and simulations are compared to each other and to the true estimates of iron grades using graphs and statistics. The conditional expectation technique reproduced the results obtained from conditional simulation extremely well and it is a viable alternative to simulation at point support. At block support the confidence intervals technique reproduced the results of the conditional simulation more closely than the median indicator kriging and in the data subsets tested the confidence intervals technique actually reproduced the true grade distribution more closely than the conditional simulation.

Jan 1, 2005

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

By N Pirouznia, F Rashidi Nejad, S Naraghi

Sungun Copper Mine, which is the second largest copper mining operation in Iran has a large tailings storage facility with a seepage control dam located downstream of the main dam. Surface and groundwater in surrounding area of the tailings storage facility has been monitored for ten years. This paper will discuss the results of the surface and groundwater monitoring and seepage control at the Sungun Copper Mine. The results of the study show that if the tailings storage facility influence the water quality of the rivers, this effect is not significant, so that the prevailing parameters of the measured parameters were within the permissible standard of drinking water in Iran.CITATION:Rashidi Nejad, F, Naraghi, S and Pirouznia, N, 2018. Surface and groundwater monitoring and seepage control at the Sungun Copper Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 439–453 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By E Deucker, A White

Gold Fields Australia (Gold Fields) has identified that improving productivity through more detailed shift planning and operational control of mining activities is a key driver to the success of their business. The Hamlet mine was chosen as a pilot site to trial a system that would allow production engineers and shift bosses to align the execution of short-term activities with the longer-term goals of the organisation.Gold Fields partnered with Deswik to introduce an on-site, collaborative, web-based system to allow mine planners to quickly build-up a detailed, activity-based, shift schedule for the coming week from the 13-week plan. Multiple stakeholders could then review and alter the plan, and then track and manage the execution of the activities.The system is designed to be integrated with production data capture systems to allow tracking of progress towards completion for each activity, as well as to plan and monitor the equipment operating in the mine. Integration of systems allowed engineers to use the large quantities of production data being captured to make informed decisions in the operations environment.The system replaced a complex set of spreadsheets that required expert users in Gold Fields to maintain. By capturing the data in a central database, the planning process is transparent and historic data from the execution of activities is available for analysis to improve productivity in the future.The system has ensured that the highest priority and critical path activities for the business are completed at the right time, improving the efficiency of operations.CITATION:Deucker, E and White, A, 2017. Productivity improvement through collaborative shift planning and tracking, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 225–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Haydon

How do you portray a large structurally and stratigraphically complex deposit to return a meaningful resource estimation, and produce a geological model that is useable for planning on a daily basis? The George Fisher Mine is located 22 km north of Mount Isa and forms part of XstrataÆs Zinc Group operations. It is currently a major producer of zinc, lead and silver in the region with an estimated total resource for all categories of 127 Mt at 100g/t Ag, 5.3 per cent Pb and 9.2 per cent Zn (June 2005). Production in 2005 totalled 2 647 492 wet tonnes for 317 699 kg Ag, 140 317 tonnes Pb and 230 331 tonnes Zn from underground operations. George Fisher (GF) consists of two deposits that are structurally complex on a mine scale, George Fisher North (GFN) and George Fisher South (GFS). Regional faulting has resulted in a 2 km long package of variably pyritic shale and siltstone that separates the deposits. This paper looks specifically at GFN. Distinct correlations exist between the two deposits based on stratigraphic matches; however, orebody characteristics, geometry and fault architectures differ significantly between the two. The deposits consist of multiple, sedimentary-hosted, stratiform orebodies from 2 to 25 m wide, separated by waste intervals of variable width. Each ore-waste interval is modelled as an individual geological domain. Structurally, George Fisher North (GFN) contains a series of major late-stage NE faults with dextral offset(s) of up to 130 m. Further complexity is added by NS, NW and NNE striking fault orientations that can produce either a loss or repeat of stratigraphy, local drag folding, orebody attenuation and block rotation. Due to this structural complexity and orebody offsets, domains at GFN are further divided into fault blocks (FB). The GFN model comprises eight FBs over a strike length of 1 km, all of which are modelled independently. As drilling progresses and additional resources are converted, further FBs will be added at major fault offsets to accommodate orebody and model expansion. This will be in addition to what is already a large and time-consuming data set to manage and update. For example, each FB has 18 domains each with two constraining wireframes (hanging wall and footwall). Each wireframe has several sets of point data depending on the type of data available, ie diamond drilling, mapping or interpretation points. This equates to over 1100 separate files to manage. Additional wireframes and files are also required for major structures, daily planning requirements and block model runs. In total some 1500 files are managed, updated and maintained for GFN alone. The ongoing need to expand as a business and optimise production in the current economic climate where there is a global demand for metal has led to an increase in production at GF. This has resulted in a rapidly growing data set and highlights the importance of practical and efficient modelling to achieve a meaningful resource estimate. This paper focuses on the geological modelling, modelling approaches and techniques employed for the GFN deposit.

Jan 1, 2006

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

By P Esteves, J L. Bechir, R Galery, C Senna, V Souto

The current moment experienced by the mineral industry is marked by a series of economic, social and environmental challenges. Among the main challenges, it is important to highlight the decreasing in ore grades with the gradual depletion of the existing deposits, the high volatility in international commodity prices and the operational inefficiencies in the mine, beneficiation, and metallurgical plants. In this context, mining companies are continuously looking for alternatives that minimize production costs and maximize overall production. In addition, recent tragedies involving tailings dam collapses in Brazil, reinforced the need for a more responsible, sustainable, and conscious mining, such as aiming the preservation and rehabilitation of the land environment. In this scenario, the Sensor-Based Sorting (SBS) technology is currently getting more space into the mining market. This separation technology aims the removal of gangue material in coarse particle size fractions, prior to comminution and concentration stages. As a consequence, the technology allows a smaller consumption of energy, water, chemical reagents and other inputs. Moreover, the sensor-based sorting is a dry processing technology and favors the reduction of fine material to be sent to the tailings. The aim of this paper is to provide information regarding the technical and economical evaluation of SBS technology applicability to a zinc silicate mining in Brazil. The project evaluation was performed in two stages: laboratory test work and the execution of a pilot plant. The execution of a pilot plant allowed the technology optimization, quantification of downstream process effects, such as a proper economic evaluation about the technology benefits. Keywords: Sensor-Based Sorting; Particle Sorting; Ore Sorting; Preconcentration; capital expenditure (CAPEX); operating expenditure (OPEX); zinc; comminution; dry processing.

Nov 10, 2020

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

Newcrest Mining Limited (NML) owns and manages the Ridgeway Gold Mine (RGM) located outside Orange in the state of New South Wales. RGM is a new underground sublevel caving (SLC) operation that is ramping up production to 4 Mtpa. The success of the SLC method at RGM is strongly influenced by production drill and blast practices. Distinguishing features of the Ridgeway SLC operation include choke blasting against broken rock, drawpoint brow preservation, loading of blastholes with different in-hole bulk emulsion densities, precharging of production rings and routine drawpoint fragmentation assessment. These areas are described in the context of RGMÆs required blasting objectives, production drilling and charging activities and innovative practices.

Jan 1, 2002