Search Documents

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By I M. Platten, Y Xie

Sampling protocols that are designed to suit the mineralisation style will result in a reduction of the nugget effect and hence resource risk. The a priori need for all sampling programs is the effective characterisation of the mineralisation type(s) to support optimisation. This requires a program of sampling for sampling followed by holistic characterisation. At each end of the coarse-gold to fine-gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated gold particles, through to extremely difficult for coarse nuggety mineralisation. Many deposits contain a proportion of both particle size types. The proportion and size of coarse gold particles has a direct impact on the effectiveness of sampling, where coarser particles will require larger samples and more specialised protocols. The nature of mineralisation geology/mineralogy and associated gold particle sizing can only be determined by sampling to facilitate optimised protocols. Mineralogical studies, focusing on particle size, particle clustering and distribution in host minerals, are required as part of wider paragenetic and metallurgical investigations. This paper discusses the role of mineralogical studies in the characterisation of gold ores for sampling optimisation through a series of case studies.

Jan 1, 2008

By D Kilkenny

Underground contractors in the mining industry must be prepared to take a position at the forefront of innovation of equipment and work methods in order to maintain a competitive advantage over in-house operations and remain relevant. Innovative concepts such as split-feed development jumbos, high capacity trucks and loader guidance systems were implemented by contractors to stay ahead of ‘the pack’. All of these are now common across the industry.The demands of regular participation in competitive tendering coupled with aggressive fleet depreciation, means contractors tend to have more communication and opportunities to work with equipment suppliers than mine owners. Therefore, they are more likely to influence equipment design and product directions. They also have a unique opportunity to assist in trialling new concepts and technologies across a wide variety of operating conditions rather than being restricted to one mine.In addition, as a ‘guest’ on a mine site, mining contractors do not have the luxury of creating the environment for their preferred systems, rather they must have the capacity to adapt their technology to suit the offered environment at a particular mine. This leads to a pursuit of adaptive technologies that can be implemented selectively and seamlessly without excessive disturbance rather than ‘all-of-mine’ systems. These incremental innovations then become available for use across the mining industry where they can add value as ‘bolt-on systems’ to existing operations.Mining contractors, therefore, act as the bellwether for industry practices and equipment. However, in order to maintain their position they must engage industry stakeholders to deliver practical, innovative and cost-effective technologies that add value and result in an improved bottom line for all. This paper uses case study material to illustrate how the Byrnecut Group has approached innovation and how the theory of Disruptive Technology applies to underground mining innovation.CITATION:Kilkenny, D, 2017. Innovation in mining – a contractor’s role, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 59–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J Seery, N Savage, A Wilson, L Nicholas

Geological modelling provides a means of spatially representing the three dimensional distribution of geological information to downstream stakeholders. The geologist completing the modelling work intimately understands the varying degrees of confidence, assumptions and extrapolation required to honour the data. Geological models are often taken and used by stakeholders without fully understanding this modelling process. This can lead to confusion amongst stakeholders when the geological model shows variable reconciliation. A method for visually communicating the confidence of the spatial distribution of geological models has been created by the Rio Tinto Iron Ore structural geology group for use primarily in geotechnical engineering investigations. A numeric confidence rating is assigned to each geological data point used in the creation of a geological surface. This is based on data type, collection method and reliability to indicate potential error in distance from its modelled location. In regions of sparse data, confidence ratings are inserted based upon the geologistÆs experience and knowledge of the geology, whereas mapped geological contacts or drill hole intersections are assigned a higher confidence rating. A regular grid of points is registered to the geological surface and each of these grid points is assigned a confidence rating using an inverse distance weighting using a nearest neighbour approach. The resulting grid is colour coded according to the confidence rating to provide a visual representation of the variable confidence of the geological surface in three dimensions. Subjectivity and bias from the geologist is minimised by critically analysing the input geological data and then applying this methodology to represent the confidence in the spatial characteristics of geological models. Understanding of this confidence enables mining professionals to make informed decisions and identify areas that require further geological investigative work. CITATION:Savage, N, Nicholas, L, Wilson, A and Seery, J, 2013. Visual communication of geological confidence - a move toward a less subjective approach, in Proceedings Iron Ore 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today's and tomorrow's mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By Floyd JM, Bultitude-Paul J

The development of a process for the extraction of antimony from materials produced by Greenbushes Tin Limited has been carried out based on theoretical and laboratory studies. The materials treated have included concentrates of tantalite and cassiterite containing antimony at levels ranging from 0.3% to 2%. Roasting under controlled atmospheres is required to stabilise Sb203 rather than the low vapour pressure metal or higher oxide. Sulphidising additives such as pyrite, pyrrhotite or sulphur give enhanced antimony removal from tantalite and cassiterite at roasting temperatures of 900¦ to 1100¦C. Substantial elimination of antimony to levels of 0.1% or less was Achieved.

Jan 1, 1986

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By J Coombes

The JORC Code lists the three core principles of Transparency, Materiality and Competency as fundamental to how mineral estimates are publicly reported. But where the principles of Transparency and Materiality can be considered conscious choices underlying decisions at the point of disclosure, Competency is a self-declared position statement based on one’s confidence to defend a technical position (as well as the functional pre-requisites of institute membership and a minimum of five years relevant experience).Developing competency in the mining industry is an ad hoc process, generally left to the individual to chart through a process of osmosis from personal work experiences that lead to a sufficient level of confidence. Companies that actually present professional development programs leading to reporting competency are rare. And even once a person has followed a program, there is no specific outline of what constitutes technical competence.No doubt, there are persons signing off on mineral statements who would benefit from developing and/or updating their technical skills (they may not even be aware of unmastered skills). Equally, there are technical practitioners who are sufficiently competent, but lack the confidence to step up and publicly report their estimates. Confidence in one’s own abilities plays a significant role in deciding when one is ready for the responsibility of submitting mineral estimates for public consumption. In addition, a person’s organisational support, such as the availability of suitable peers and professional development programs, and opportunities to learn from a variety of technical projects contribute to developing relevant experience. Increased exposure in both technical breadth and depth enhance confidence in one’s ability and competence.The mining industry provides numerous opportunities through direct and indirect means to develop the competency underpinning a stable reporting code. This paper examines a theoretical framework and associated processes that could be used to examine how the mining industry, companies and individuals collaborate to develop this vague principle of competency. This paper seeks to initiate research with the express purpose of enabling more effective and efficient development of reporting competency in our industry.

Aug 22, 2011

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

Conditional simulation can be used to determine the probabilities of block iron-grades being above selected cut-offs. However, there are much faster alternatives that can produce acceptable results. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody is used as the basis of a case study to assess alternatives to simulation. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce data subsets. A complete distribution of iron grades for points or blocks is obtained utilising the data subsets and the following techniques: conditional simulation, median indicator kriging, the probability from conditional expectation and confidence intervals attached to the estimation of blocks in the framework of the discrete Gaussian model. The complete blasthole dataset is considered to represent the true iron grades at sample point support while the ordinary kriging estimate derived from these samples is considered to represent the true block grades. The distributions obtained from point estimates, block estimates and simulations are compared to each other and to the true estimates of iron grades using graphs and statistics. The conditional expectation technique reproduced the results obtained from conditional simulation extremely well and it is a viable alternative to simulation at point support. At block support the confidence intervals technique reproduced the results of the conditional simulation more closely than the median indicator kriging and in the data subsets tested the confidence intervals technique actually reproduced the true grade distribution more closely than the conditional simulation.

Jan 1, 2005

By Shiels O. J

The major Permian coal deposits of N.S.W. are in the Sydney-Bowen Basin and associated small deposits occur in structurally isolated areas; a further deposit is present in the Oaklands Basin. - The Sydney-Bowen Basin in New South Wales comprises the sub basins, the Sydney Basin and the Gunnedah Basin. Coal measures in these basins are near the top of the Permian succession and within and below an underlying marine sequence. The coal deposits can be conveniently described in units in which the coal geology is homogeneous. The Clyde Coal Measures and Yarrunga Coal Measures contain no seams of economic significance and occur beneath the marine beds in the south of the Sydney Basin. The Greta Coal Measures are economically significant and represent a brief interlude in the marine sequence in the north of the Sydney Basin and equivalents are present in the east of the Gunnedah Basin. The Tomago Coal Measures crop out above the marine sequence east from the Lochinvar Anticline and dip southeast to uneconomic depths. The Newcastle Coal Measures are historically and economically very important and overlie the Tomago Coal Measures and these measures will continue to be important although future mining will be faced with greater depths. To the west of the Lochinvar Anticline the Singleton Coal Measures, equivalent to the Tomago and Newcastle Coal Measures, crop out. This unit represents the thickest development of coal measures in the State and has a very large potential for both open cut and underground mining. Equivalents of the Singleton Coal Measures, the Black Jack Coal Measures and the Booroomin Group crop out on the east side of the Gunnedah Basin and probably are widespread across the Basin. They have less economic potential than the Singleton Coal Measures. In the southwest of the Gunnedah Basin, Illawarra/Singleton Coal Measures crop out over extensive areas and possibly have a large potential for underground mining under low cover. The Illawarra Coal Measures are exposed along the western margin of the Sydney Basin and thicken as they dip into the Basin across a shelf. The outcrop area is currently mined and the shelf has considerable potential for future mining. The highest rank coals in the State are in the Illawarra Coal Measures in the south of the Sydney Basin. The deepest coal mining is in this area and its continuing success is of great importance to the future exploitation of the resources of the Basin. The Tomago, Newcastle, Singleton and Illawarra Coal Measures extend into and meet in the central area of the Sydney Basin but they are under thick cover and are not considered to be economic at present. Permian coal measures occur in isolated areas in the New England Fold Belt and have limited economic potential. The Oaklands Basin in the south of the State contains a large reserve of low rank coal.

Jan 1, 1975

By R Rankine

Backfilling with paste fill has been an integral component of open stoping at Cannington since commencement of operations. Efficient paste filling is critical to successful mining of the Cannington orebody. There has been a deliberate and ongoing effort into research and development of paste, with the focus being to optimise the performance and cost of paste. This paper describes the latest research and operational issues of Cannington paste fill.

Jan 1, 2005

By Ring R. J, Waters D. J, Vautier F. E, Fulton E. J

Laboratory leach tests have been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid (permonosulphuric acid) as an alternative oxidant to pyrolusite in the leaching of uranium ores. Results demonstrated that Caro's acid reduced acid consumption in leaching and the lime required for neutralisation of tailings liquor. The uranium extraction was unaffected by choice of oxidant.Following this study, Interox Chemicals Pty Ltd arranged a plant trial using Caro's acid at the Nabarlek uranium mill of Queensland Mines Ltd. The trial confirmed that significant savings in acid and lime usage can be achieved under plant conditions.Plant operations also demonstrated that Caro's acid has a number of significant operating advantages over pyrolusite.Queensland Mines Ltd have recently decided to convert their leaching process from pyrolusite to Caro's acid. The new system is expected to be fully operational by mid 1983.

Jan 1, 1983

By Lloyd C. J

The uranium markets are at present well covered by available producers. However the predicted increase in demand, recently reinforc- ed by the Arab oil crisis, will by, the early 1980s'outdistance supply. Current trends are towards light water reactors with-fast breeder reactors not expected to make any significant impact to the mid 1980s. The proposed lifting of the US embargo on the use of foreign uranium in US reactors will expand the market available to non US producers. A balancing in supply and demand worldwide will probably occur in the early 1980s. Australia's potential producers at present hold about 20 percent of the worlds U308 resources. Three companies, have contracts to supply nearly 10 900 tonnes of U308 between now and 1986 which represents about 1 percent of the predicted demand to 1986. Australian producers need to establish themselves more firmly in the market place in order that other countries will not replace us. Contracts can be written now which will allow for world market prices to be paid in the future, thus protecting the Australian producer.

Jan 1, 1974