Search Documents

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By K. D. McBean, W. H. Hannay, B. A. Stimmel

The electrolytic plant at Trail, B. C., was erected by the Consolidated Mining and Smelting Company of Canada, Ltd., for the treatment of zinc ores and concentrates, particularly those of the Sullivan mine at Kimberley, B. C. It began operations in 1916 at a rated capacity of 60 tons of cathodes per day, which has been steadily increased to the present production of 400 tons per day. The Sullivan has furnished the greater part of the zinc so far produced, although notable tonnages of customs zinc concentrates have been treated. The maximum yearly tonnage of customs concentrates, 25,000 tons, was treated in 1926. Practically no customs concentrates hale been treated since 1929. The total bar zinc production to the close of 1935 was 1,092,782 tons. The zinc mineral in the Sullivan ore is marmatite of somewhat variable composition, ranging between 6ZnS.FeS and 8 ZnS.FeS. Practically all the zinc ores tributary to this plant are marmatites; and the iron content of the zinc mineral varies considerably. The formation of zinc ferrite during roasting is now a matter of common knowledge, so the possible extraction from any zinc concentrate is largely a function of the iron content; the progress made in concentration is reflected directly in zinc-plant recovery. The Trail plant operafes on the low-acid system, as do all the other major plants on this continent at present operating, except the electrolytic plant of the Sullivan Mining Co. at Kellogg, Idaho. The new Magdeburg plant, in Germany, occupies an intermediate position between high and low acid. Plant operation at Trail will be treated in this paper under five main sections: roasting, leaching and purification, electrolysis, cadmium recovery and melting. The oxide section of the plant, treating zinc fume from re-treatment of lead blast-furnace slag, is practically a separate zinc plant; this is necessary because of the presence of fluorine in the smelter zinc fume. Cadmium is recovered electrolytically from the purification residues of both the sulphide and oxide leaching plants.

Jan 1, 1937

By James O. Lewis

Gravity drainage is the self-propulsion of oil downward in the reservoir rock. Under favorable natural and operational conditions, it has been found to effect recoveries comparable to water displacement. With modern technical knowledge, the operator can often make a choice between dissolved gas drive, water drive and gravity drainage as the principal recovery agent in a reservoir. It is desirable that the opeator be able to determine which of the three agents will be most effective under each set of conditions. So far, gravity drainage has received less consideration than the other two. In this paper. an endeavor is made to set forth some of the principles of gravity drainage, to point out the types of reservoirs favorable for it, and to show how it may be applied in them. Field examples are described and discussed. Introduction Since early in the history of the oil industry, it has been recognized that gravity is one of the three important natural forces for expelling oil from the reservoir rock. As knowledge of the technology of oil recovery progressed, ideas changed with respect to the relative importance of the three forces and with respect to the manners in which they functioned. For a time, disproportionate emphasis was placed on the importance and function of gas and the need for conserving gas pressures. More recently, disproportionate emphasis has been placed on encroaching edge water. Only lately has there been evidence that the function and importance of gravity was to receive due consideration. Study of this neglected phase of oil recovery is needed to round out our knowledge of reservoir behaviors and to gain a balanced viewpoint of the interplay of forces that may operate in varying importance in reservoirs. The purpose of this paper is to discuss mainly in a qualitative way, the functions of gravity, to present some concrete instances where it has been important and to raise some questions that should be investigated further. Oil-recovery Agents The important natural agents for effecting oil recovery that may be originally available in a reservoir are gas, both dissolved in the oil and free in gas caps, encroaching edge water and gravity. Each of these agents can act in a dual capacity—physically to overcome the surface energies that hold the oil within the pores and mechanically to overcome viscous . resistance and to propel the oil through the porous reservoir rock to the wells. Advancing edge water displaces the oil from the pores and lifts it updip to structurally lower wells. Gravity drains the oil from the pores and flows it downdip to the wells. Gas displaces oil from the pores, entrains it in the gas stream and flows it to the wells, but gas in solution also affects the physical properties of the oil and thus can influence oil recovery by the other agents, whether or not the mechanical energy in the gas is utilized. Of the two functions of these agents, the more important is the ability to dis-

Jan 1, 1944

By L. J. Ingvalson, Roy H. Miller

IN 1948, as part of a program to expand the copper tube mill facilities of the American Brass Co. plant at Kenosha, Wisconsin, plans were formulated to convert the 100 ton capacity anode casting furnace at the Great Falls, Montana plant of the Anaconda Co. to the production of 3 in. phosphor -ized billets. The furnace was rebuilt completely and construction was started on an addition to the building. Members of the Great Falls staff visited various billet casting plants to draw upon the experience of other producers of this type of casting. Many features of other plants were incorporated into the Great Falls plant but, in addition, many new designs were made and perfected to make the plant the most advanced of its type. Construction was begun in 1949, with the intention of having the plant in production in the early part of 1951. In January 1951, as the plant was being rushed to completion, the government placed restrictions on the production of copper tubing. As a result, work was halted and the plant lay idle for two years. Interest was reactivated in May 1953 with the lifting of restrictions on copper. Plans were laid to go into production in July and the first charge was taken out July 1, 1953. Basically the plant is designed to produce from cathode copper a 3 in. diam billet, 50 in. long. weighing 110 lb, and containing 0.013 to 0.036 pct P, at a rate of 150,000 Ib per operating day. These billets are to be pierced and drawn into tubing. Furnace The furnace is a 100 ton capacity reverberatory type, gas fired furnace; 21 ft long and 9 ft wide. Gas is introduced to the furnace through two 38 hole Mettler gas burners. These burners are of chrome nickel alloy with four jets per hole. The furnace is charged with cathodes from the Electrolytic Copper Refinery plus return scrap from the casting operation by means of a Wellman Seaver Morgan Co. 7,000 lb capacity charging machine. The charge crane has a 20 ft boom and fork peel provided with an air ram to push material off the peel. The machine travels on overhead tracks and can be moved in any direction. The boom can be raised and lowered and swung through an arc of 180". With well stacked units of 6,000 lb, an experienced operator can put the first charge into the furnace in 40 min. After charging, the steel framed silica brick charge door is put in place and sealed with clay. After melting and skimming off the slag, the copper is blown until an oxygen content of 0.40 pct is reached. The metal is then heated to 2180°F, covered with coke, and poled. Poling is continued until a 3 in. diam test billet, 8 in. long, shows a flat set. The oxygen content is usually 0.030 pct at this time. At the end of poling, a temperature of 2160" to 2180°F is desired. In the side of the furnace opposite the charging door is the taphole slot, extending 36 in. upward from the bottom of the furnace. It is 4½ in. wide at the outside face and widens to 9 in. at the inside face of the furnace. It is filled with a wet mixture of sand, fireclay, and crushed coal. Flow of metal

Jan 1, 1957

By Herbert H. Kellogg, Hugo Vasquez- Rosas

Recently the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authorsl-5-l8 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, laurylamine hydro-chloride, as a collector for the flotation of galena-sphalerite ores. The results show that laurylamine hydrochloride (LAmHCl), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. Contact-angle Tests The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-coverkd glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the clean surface to air or any other source of contamination.

Jan 1, 1947

By G. H. Shefelbine

DISCOVERED during the time of the Spaniards, the Namiquipa silver-lead-zinc mines in Chihuahua, Mexico, remained idle until 1916, when mining claims were first denounced. About 1922 a Japanese company, the Santo Domingo Mining Co., was formed to mine the oxide silver ore. The company built a 75-tpd cyanide plant and mined in the area for a number of years. Because of an error in surveying in one of the company's mines situated in another district, mining was carried over into a claim owned by General Marcel Caraveo, at that time governor of Chihuahua. Santo Domingo Mining Co. lost the resulting lawsuit and consequently had no capital to continue operating at Namiquipa. Later, Ray Brown and Eugenio Caballero formed a company to operate the mine, shipping crude ore to the American Smelting and Refining Co. smelter at Avalos, Chihuahua. The cyanide plant was changed to flotation with a capacity of 75 tons per 24 hr. In 1936 the property was again closed owing to labor trouble, a drop in the price of silver, and increased water in the mine.

Jan 10, 1957

By Donald W. Scott, L. A. Roe, B. J. Sweo

INTRODUCTION THIS paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizers and organic dyes, and 35 parts of water are added to loo parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder' in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the overspray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1947

By Alex McCoy

SAMPLING of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines-laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. LABORATORY INVESTIGATIONS ON EMULSIFIED OIL Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. S. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy,

Jan 8, 1919

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By Archer Wheeler

THE copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minere du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1932

By C. W. Hill

IN a previous article preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) FIG. 1.-STEPS IN THE ELIMINATION OF LEAD. (The lead line, at point 105.8 in the violet portion of the spectrum, is seen between the two copper Lines,-102.29 and -106.29, lying close to the latter. The crowded faint lines are due to the carbon are.) 1. OUTLINE OF METHOD A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 10, 1918

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By Robert M. Yonco, Irving Johnson, Martin G. Chasanov

The thermodynamics of the cadmium-rich portion of the Pu-Cd system has been studied with a high-temperature galvanic-cell method. The partial phase diagram of the Pu-Cd system was determined. The existence of the intermediate phases PuCd11 (cubic BaHg11 structure, ao= 9.282) and PuCd6 (cubic, CeCd6 structure, a, = 15.59) was established. The existence of at least one other intermediate phase richer in plutonium was indicated. PuCd11 was found to peritectically decompose into PuCd6 and liquid at 406" * 2°C. The solubility of plutonium in liquid cadmium may be represented by the equations: (355' to 399°C) log (at. pct Pu) = 6.223 -4282T-1 (399° to 632°C) log (al. pct Pu) - 5.148 - 5277T-1 > 1.156 x 106 T-2 The free energy of formation values (kcal per mole) of the two intermetallic phases are given by the equations: (PuCd11), ?Gf= -45.9 + 35.7 x 10-3 T (PuCd6), ?Gf0- -39.27 + 25.86 X 10-3T The excess free energy (kcal per mole) of plutonium in liquid cadmium may be represented by the equation: -(-16.72 * 29.54 NPu) 10-3T in which Npu and Ned are the atom fractions of plutonium and cadmium. The thermodyanamics of the U- Cd and Pu-Cd systems are compared. THERMODYNAMIC information on systems of the actinide metals with low-melting metals, such as zinc and cadmium, is useful in the design of pyro-metallurgical processes for the purification of nuclear reactor fuels. The thermodynamics of the Pu-Zn,1 Th-Zn.2,3 U-Zn,4-5 and U-Cd6 systems have been reported. The present report on the Pu-Cd system concerns the liquidus composition in the cadmium-rich region, the characterization of the two most cadmium-rich intermetallic phases, and the thermodynamic properties of these intermetallic phases and dilute liquid solutions of plutonium in cadmium. EXPERIMENTAL Phase Studies. The liquidus composition was determined by analysis of filtered samples of the liquid phase withdrawn at a series of temperatures. The apparatus and procedure were identical to that used in the previous study of the Pu-Zn system.' Briefly. a sample of the melt was withdrawn into a tantalum tube fitted with a porous tantalum filter (30-µ pore). the entire sample dissolved in hydrochloric acid (to avoid errors due to segregation

Jan 1, 1965

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.' When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942