Search Documents

By C. H. Mathewson, P.W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By Frank Schrader

INTRODUCTION THE present sketch is submitted by request in the hope that it may serve as a basis for geologic discussion of the mining camps in Mohave County, which is experiencing a marked revival of activities. The region, commonly known as the Mohave district and Kingman district, lies in western Arizona in the southern part of Mohave County, bordering California and Nevada on the west (Fig. 1). Kingman, the principal-town; is situated near the center of the area. on. the Atchison, Topeka & Sante Fe Transcontinental Railway. This region is composed of naked desert ranges of mountains and broad detritus-filled valleys, the southern extension of the characteristic topography of the Great Basin. In altitude it varies from 500 ft. in the southwest to 8,300 ft. on Hualpai Peak southeast of Kingman. The mountains trend north-northwest. They rise about 3,000 ft. above the valleys, are generally rugged and were formed mainly by erosion. They are composed in the main of a, complex of pre-Cambrian granitoid rocks which underlies the area as a whole. Like the valleys, they average about 10 miles in width. Beginning on the east, they are the Grand Wash Cliffs, the Cerbat Range, the Black Mountains or River Range, and the Eldorado Range. The upper or dominantly cliff half of the Grand Wash Cliffs, marking the edge of the Colorado Plateau, is composed of nearly horizontal sedimentary Paleozoic strata of the Grand Canyon section, and the lower half of the underlying pre-Cambrian complex. The Cerbat Mountains situated in the central part of the area, and the Black Mountains situated between Detrital-Sacramento Valley on the east and Mohave Valley, the great trough of the Colorado River, on the west, are locally flanked or overlain by Tertiary volcanics (Fig. 2). The latter consist of five groups of mountains of which the most important is the Black Mesa group on the south. The Eldorado Range, rising from the great trough of the Colorado on the west and containing Searchlight, Eldorado Canyon, and other camps, is topographically and geologically similar to the Black Mountains.

Jan 10, 1916

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By A. J. Bowie

Jan 1, 1879

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By C. R. Johnson, R. A. Greenkorn, E. G. Woods

A new method of reservoir evaluation called pulse-testins has been developed for describing formation properties between wells. Pulse-testing utilizes a sensitive differential-pressure gauge at a responding well to measure and record the response generated by a series of flow rate changes (pulses) at an adjacent or pulsing well. Since the pulse-test instruments have a sensitivity of about 0.001 psi, pulses of several hours or less in duration will generate a measurable response in most reservoirs. For this reason, many well pairs can be tested in a short period of time with little interference in field operations. Comparison of pulse-test results to conventional testing methods shows that the pulses obey unsteady-state, compressible-flow theory and thus provide a measure of both transmissibility (kh/µ) and storage (Fch). In additian, the method can be used qualitatively to describe communication across faults and between zones, and direction and tnagnitude of fracture trends. INTRODUCTION To obtain maximum usefulness of new reservoir analysis methods as well as to aid the field engineer in understanding local reservoir anomalies, improved methods are needed to describe heterogeneities in specific reservoirs. Optimum well spacing, equipment specifications, well completion design and especially the economics of pressure maintenance and secondary recovery programs depend on the extent and location of the heterogeneities that affect flow behavior in the field. One method for obtaining a measure of areal reservoir heterogeneity is an interference test. In the simplest interference test. constant-rate production or injection is initiated at one well and the effect of this flow is measured as pressure vs time at another well. Thus, during interference tests the flow characteristics of the formation are determined in situ. Despite their obvious usefulness in reservoir delineation. interference tests have not enjoyed frequent usage. Reasons for this have been the weeks or months required in many fields to obtain a pressure response measurable with conventional gauges, and the interruption of routine field operation during the field-wide shut-in normally required during these long times. Also, only average properties of the relatively large volume of the reservoir disturbed during these long times can normally be obtained — variations in properties between individual wells cannot be delineated. To eliminate these drawbacks of conventional tests, a special reservoir description technique called pulse testing' has been developed. Pulse-testing has several advantages that make it more convenient and practical for field use than interference tests. Valid tests are more certain because use of a series of flow disturbances gives rise to a diagnostic pressure response that can more readily be distinguished from unknown trends in reservoir pressure and other "noise." The time required is only a fraction of that for an interference test because a special, high-sensitivity differential pressure gauge can detect a much smaller pressure change. Variations in properties between individual wells can be delineated because of the relatively small volume of the reservoir disturbed during these short times. Finally, wells other than the pulsing and responding wells do not have to be shut in or carefully regulated.

Jan 1, 1967

By William E. Harris

Time and experience have demonstrated that by means of the Waelz process zinc, lead, cadmium, arsenic, antimony, bismuth and tin can be volatilized satisfactorily. In this way difficult gold ores are being treated to allow for the recovery of the precious metal. Iron ore containing zinc is being treated to remove the zinc and recover the iron. In Germany, thallium is being recovered in commercial quantities from the zinc oxide fume; indium, germanium and gallium are also concentrated to a degree warranting recovery, even though these rare metals are only recognizable in the ore by means of the spectroscope. The physical, chemical or mineralogical condition of the raw material affects very little the applicability of the process. The name Waelz is derived from the German word Waelzen, meaning a "trundling motion," which very aptly describes the movement of the charge through the slowly rotating kiln. The recovery of zinc and lead by volatilization in a rotary kiln has its origin in a process patented in 1910 by Edward Dedolph, of British Columbia. The Dedolph patent was taken over by the Metallgesell-schaft of Frankfurt-on-Main, Germany, which in cooperation with the Griesheim-Elektron, now a part of a large industrial combine, introduced certain improvements (Ohlmer, Specketer patents), but without bringing the process to a state suitable for large-scale operations. The war temporarily stopped all work on the process, and it was not until after the war that the Krupp Grusonwerk, of Magdeburg-Buckau, Germany, quite independently of the Metallgesellschaft, instituted research work in this field of metallurgy, which in 1923 led to the Waelz process proper. The Krupp Grusonwerk and the Metallgesellschaft A.G. later on collaborated, and by their joint efforts further developed and perfected the Waelz process, which they are marketing together as "Waelz-Gemeinschaft." The process is capable of treating a varied type of material; for instance, oxidized and sulphide zinc ores, calamine (zinc carbonate ore) waste dumps, jig tailings, jig slimes, table concentrate slimes, brass ashes, zinc-bearing iron ores (where the iron sinter is the real objective and the zinc oxide a by-product), electrolytic-zinc leach residues, zinc muffle residues and works sweepings, lead-furnace slags, tin ores and slags, anti-

Jan 1, 1937

By Raymond Edmundson

BARITE probably was first mined in the United States in 1845, when a small deposit was operated in Prince William County, Virginia1. The next state to produce barite was Missouri, and according to Weigel2, mining began about 1860. Virginia was the leading producer during the early period of barite mining, but by 1893, Missouri was producing almost an equal amount3. From this date, Virginia, although not the leading producer, furnished large quantities of crude barite until oper-ations gradually declined about 1907. Since 1910, there has been only one producer in Virginia. It is not known when barite was discovered in each of the Virginia areas (Fig. 1), but it is reliably reported that mining on a commercial scale began in Campbell-Pittsylvania counties about 1874; Smyth County in 1877; and in the Russell-Tazewell area about 1890. Barite is widely distributed in Virginia, occurring in nineteen counties. The localities that contain material of some economic value have been grouped into six areas (Fig. 1), each designated by the county or counties in which the barite is found. As many of the smaller areas show a similarity in geologic occurrence, they will be considered in this paper as two major groups; namely, Appalachian Valley and Piedmont Province. The first group, which includes the barite deposits of Russell, Tazewell, Smyth, Botetourt and Roanoke counties, lies northwest of the Blue Ridge and its foothills and southeast of the Appalachian plateaus. The other group includes deposits from the Blue Ridge on the west to the western margin of the Coastal Plain, in Campbell, Pittsylvania, Bedford, Grayson, and Fauquier counties.

Jan 1, 1936

By Yinchang Wang

1. INTRODUCTION 1. Subject, and Scope The formation of the oxidized ores of zinc has been recognized as a subject of great importance in economic geology. For many years these ores have been much sought, partly because they are more desirable for metallurgical treatment and partly because they are apt to be freer from gangue than is the sulphide of zinc. Up to very recent years the oxidized ores were the principal source of the metal and at present they still furnish a large portion of the commercial production. . The oxidized ores of zinc include six minerals, as shown in the-following table

Jan 9, 1915

By A. M. Sarem

For the performance prediction of multiphase oil recovery processes such as steam stimulation, there is an acute need for three-phase relative permeability data. No fast and simple experimental technique, such as the unsteady state method proposed by Welge for two-phase flow, is available for the three-phase flow. In this paper, an unsteady - state method is presented for obtaining three-phase relative permeability data; this method is as fast and easy as Welge's method for two - phase flow. Analytical expressions are derived by extension of the Buckley-Leverett theory to three-phase flow to express the saturation at the outflow face for all three phases in terms of the known parameters. It is assumed that the fractional flow and relative permeability of each phase are a function of the saturation of that phase. Other simplifying assumptions made include the neglect of capillary and gravity effects. The effect of saturation history upon relative permeability is acknowledged and attainment of similar saturation history in laboratory and field is recommended. The required experimental work and computations are simple to perform. The test core is presaturated with oil and water, then subjected to gas drive. During the test, required data are the rates of oil, water, and gas production, together with pressure drop and temperature. The ordinary gas-oil unsteady-state relative permeability apparatus can be readily modified to measure the required data. The proposed technique was applied to samples of a Berea and a reservoir core. The effect of saturation history upon relative permeability was studied on one Berea core. It was found that increase in initial water saturation has a similar effect upon three-pbase relative permeability as it does in two-phase flow. INTRODUCTION In the light of increasing demand for three-phase relative permeability data for predicting the performance of thermal and other multiphase-flow recovery processes, a simple and accurate method of experimental determination of such data is extremely desirable. Leverett and Lewis 1 described the simultaneous flow method of obtaining three-phase relative permeability data. However, Caudle et al.2 reported that this method is very time consuming and cumbersome. Corey3 proposed calculating the three-phase relative permeability from measured krg data. Corey's theory is based on simplified capillary pressure curves,4 assuming a straight line relationship between I/Pc2 and saturation. Also, Corey's method assumes a preferentially water-wet system. The simplest and quickest method of obtaining three-phase relative permeability data is the unsteady-state method where, for instance, oil and water are displaced by gas. However, in such a test the correlation of average saturation with relative permeability does not give a valid relationship because the rates of oil, water and gas flow in the sample change continuously from the upstream to downstream end. This difficulty in calculating valid relationships was solved by Welge for two-phase flow by deriving an expression for determining the outflow face saturation from Buckley and Leverett frontal advance equations.5,6 In this paper, relations are established to determine the outflow face saturation and relative permeability to all phases in a three-phase flow displacement experiment. PROPOSED METHOD The fundamentals established by Buckley and Leverett5 for two-phase flow were extended to three - phase flow and used as a basis for the derivation of saturation equations. This approach is comparable to Welge's6 use of Buckley and Leverett theory in arriving at expressions to determine the outflow face saturation of the displacing fluid in a two-phase flow system.

Jan 1, 1967

By M. Cohen, D. Caplan

The scaling characteristics of three Fe-Cr alloys have been investigated by determining their weight gain vs. time curves at 1600° to 2000° F. The scales formed thereby have been examined using the techniques of X-ray diffraction and spectrographic and metal-lographic analyses in an attempt to explain the discontinuities in the curves and to elucidate the mechanism of scaling. DESPITE the considerable number of investigations that have been carried out on heat resistant alloys, the characteristics of the scales formed at high temperatures are not fully known. The research reported here was undertaken in an attempt to ascertain the mechanism of scaling of the stainless steels. Scaling experiments were carried out first, the weight increase of the specimens being followed continuously with time. It was observed that, as well as showing the expected decrease in oxidation rate with time, the oxidation curves showed breaks corresponding to intermediate periods of accelerated oxidation, after which protectiveness again increased. This phenomenon was observed with austenitic stainless steels (types 302, 309, and 330) and with Fe-Cr alloys (types 410, 430, and 446), but only the latter are treated in this report. An examination of the scales was made using the techniques of X-ray diffraction and spectrographic and metallographic analyses in an attempt to obtain a correlation between the nature of the scales and the oxidation curves. A search through the literature revealed only a very few previous reports of such periods of accelerated oxidation. Dunn' found breaks in the oxidation-time curves of some Cu-Si alloys but saw no rational explanation of the phenomenon. Heindlhofer and Larsen2 attributed a discontinuity in the weight gain-time curve of iron at 1290°F to the formation of blisters, the subsequent cracking of which exposed an unprotected surface and permitted rapid oxidation until a new protective scale had been reestablished. They advanced no explanation, however, for what they termed the peculiar behavior of a 27 pct Fe-Cr alloy at 2000°F which gained weight very rapidly in between two periods of very slow weight gain. Portevin, Pretet, and Jolivet3 in describing breaks in the weight gain-time curves of Fe-A1 alloys suggested that they might be associated with the occurrence of localized and deeply oxidized areas on the specimens. Bandel4 in a general discussion of oxidation curves of heat resistant alloys considered that the discontinuities were due to a local disruption of the protective layer by the growth of iron-rich oxides. Day and Smith" in their report on the scaling of a large number of iron alloys noted but did not explain occasional relatively rapid changes in oxidation rate at higher temperatures. Chevenard and Wache6 found breaks, often two per specimen, in the oxidation curves of an 18-8 type alloy. They suggested that the cause might be a depletion in chromium of the surface layer of metal due to its selective oxidation, the resultant high concentration of iron and nickel in the scale leading to a poorly protective scale. McCullough, Fontana, and Beck' explained the breaks in the oxidation curves of types 304, 430, and 410 alloys as due to mechanical ruptures. Experimental Work Table I lists the chemical compositions of the materials used. Cylindrical specimens 1/4 in. in diam and 11/2 in. long were machined from cold rolled % in. rod. After a fine finish cut with a sharp tool, the specimens were abraded while still mounted on the lathe with Nos. 2, 1, 0, and 00 metallographic grade emery papers. A 3/64 in. hole was drilled at a distance of 1/8 in. from one end to permit suspension in the furnace. Specimen Nos. 1, 2, and 3 were tested with this surface preparation. All others, after being similarly prepared, were electropolished in a perchloric-acetic electrolyte, electrical contact being made by pressing a tapered platinum hook into the drilled hole. The specimens were then washed in hot water, rinsed with distilled water, rinsed with methanol, dried at 120°F, and weighed. Thereafter,

Jan 1, 1953

By C. H. Mathewson, P. W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By N. A. Warner

Dense cylindrical specimens of artificial hematite were reduced in hydrogen over a range 0-f total pressures between 0.1 and 1.0 atm and temperatures between 650" and 950°C. Hydrogen reduction at a total pressure of 1.0 atm in the presence of a chemically inert diluent and reduction in hydrogen/water mixtures were also studied Znter.face movement during reduction was followed using metallographic techniques. Substantiu1 partial-pressure gradients are shown to exist in both the gas film and the reduced iron layer. The results are consistent with a mixed-control mechanism involving an interaction of gaseous-difusion effects with a first-order reversible chemical reaction at the iron/wüstite interface. Over the hydrogen-pressure range of 0.1 to 1.0 atm, the rate is not directly proportional to the hydrogen pressure in the bulk gas stream. Nitrogen dilution of the reducing gas masks the true effect of hydrogen partial pressure by influencing the effective molecular dif-fusivity and gives an apparent first-order relationship. The transport of hydrogen and water vapor across the iron layer is consistent with molecular gaseous diffusion rather than a Knudsen diffusion mechanism. ALTHOUGH the literature on the reduction of iron oxides is very extensive, it is only comparatively recently that a definite quantitative model for the reduction of hematite has been proposed. This development has been largely due to the work of McKewan. An extensive literature review of previous work has recently been compiled by Themelis and Gauvin. Exclusive control by gaseous diffusion in the reduction of hematite has been recently advocated by Kawasaki and coworkers.' Although the results of the latter workers are of considerable practical significance, the extreme porosity (approximately 30 pct) of their specimens precludes their application to a kinetic evaluation of the reduction of dense polycrystalline hematite. The salient features of the kinetic model used by McKewan for the gaseous reduction of dense hematite at temperatures in excess of 560°C (when FeO is stable) are: 1) The reduction is a topochemical reaction taking place through 'the series FeO/FesO4/FeO/ Fe; 2) The gas-solid type of reaction takes place only at the FeO/Fe interface and the internal reduction: FeO proceeds by solid state diffusion; 3) The iron layer formed is quite porous and offers negligible impedance to gaseous diffusion; 4) The rate-controlling step in the reduction is a chemical process occurring at the Fe/FeO interface. In view of the relatively fast reaction rates involved when hematite is reduced in a stream of hydrogen, it seemed possible that the simplifying assumptions of negligible diffusional resistance in both the bulk gas phase and the reduced iron layer could introduce serious errors in the interpretation of experimental reduction data. The present work was initiated to elucidate the effect of gaseous diffusion on the reduction rate and to determine its possible influence in the formulation of the reaction mechanism at the metal/oxide interface. EXPERIMENTAL Procedure and Apparatus. Dense cylindrical compacts of artificial hematite were prepared by sintering pressed compacts of reagent-grade ferric oxide, containing 99.6 pct FezO, in air at 1200°C for 80 hr. The resulting compacts had a final porosity of less than 2 pct and a height and diameter of approximately 1 cm. Variations in sintering atmosphere from air to pure oxygen, in sintering time from 20 to 80 hr, and temperature from 1150" to 1250°C had no effect on the subsequent reduction behavior. The reduction of the samples took place in a vertical tube furnace in which was placed a 1-in. transparent silica tube. The 24-in. heated length

Jan 1, 1964

By Walter Herd

Fox the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of -Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method was employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence, had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously- pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining. No. 2 Seam, Springhill, at depth, and records the 'conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By R. W. Guard, M. E. Fine

By treating the dislocation like a surface and ap-plying the usual thermodynamic treatment to the adsorption process a Gibbs adsorption equation for dislocations was derived. For extended dislocations in binary solutions the adsorbed concentration on the fault, X2a, may be computed from (jo/da2b) where a2b is the activity of the solute in the bulk material and s is the stacking-fault energy. Using the data of Howie and Swann for s the adsorption concentration goes through a maximum at 2 at. pct Al in Ag-Al, 10 at. pct Zn in Cu-Zn, and 8 at. pct A1 in Cu-Al. The pinning stress calculated from this concentration difference goes Ihrough a maximum at the same concentration us the peak in X2 a. The computed pinning stress thus does not vary with composition in the manner predicted by Suzuki, as was also pointed out by Hendrickson. The results are compared with the stress increment which can be attributed to Suzuki locking in Cu-Zn and Cu-Al stress-strain curves. They both agree in magnitude and in the location of the maximum. The predicted and observed maximum values for the Cu-Zn system (where activity data are available) are 700 g per sq mm (predicted) and 1000 g per sq mm (measured, laking into account the orientation factor of 2.2 to convert poly-crystalline to single-crystal data). CERTAIN simple internal surfaces may be regarded as dislocation grids. This fact suggested that it might be profitable to consider certain phenomena related to segregation of solute atoms at dislocations from the point of view of the thermodynamics of surfaces and surface adsorption. A general treatment of this type is given and then the results are applied to Suzuki segregation and pinning. Confirmation of the results is obtained from comparison of stress-strain behavior for copper and copper-base alloys. Two kinds of dislocations need be treated: perfect and extended dislocations. In either case the line tension of a dislocation, ?. the work which must be done to increase the length of dislocation by a unit length, is analogous to the surface tension. For an undissociated dislocation ? is the self-energy of a unit length of dislocation; for an extended dislocation where is the self-energy per unit length of a pair of partials far enough apart so that there is no interaction energy, is the interaction energy per unit length, is the stacking fault energy per unit area, and w is the equilibrium separation of the paired partials. In the absence of an applied stress the force pushing the dislocation partials apart in a close-packed structure is Gb2/12p where G is the shear modulus, b is the Burgers' vector of the complete dislocation, and is the separation of the partials. At the equilibrium separation, w this force equals s. Thus

Jan 1, 1965

By Donald H. McLaughlin, Reno H. Sales

ADAPTATION to mining needs of the rich store of geologic knowledge concerning mineral deposits and the application of principles of the science to specific problems in the finding, development and stoping of particular ore bodies are the major tasks of the mining geologist. On him to an increasing degree is placed responsibility for estimation of ore and appraisal of mineralized ground, for explicit guidance of exploration and development, and for reliable advice with regard to the many geologic conditions that influence mining operations. In the long continued and steady efforts to meet these requirements, a special skill in close observation, recording, and quantitative interpretation has been developed, particularly by geologists on staffs of mining companies, which in many districts has proved to be effective, not only for technical ends, but also for advancement of scientific understanding. The foundations for mining geologic work were laid in most districts of the West by investigations of the United States Geological Survey. For years they have provided a reliable basis for geologic thought with regard to ore deposits, and later studies have enriched and supplemented rather than superseded them. In very few districts have the geologic relations stated in the earlier papers needed serious modification or revision, in spite of new evidence subsequently made available in abundance by mining exposures. Indeed, one of the chief satisfactions derived from success in mining geologic work is the assurance that it gives of the correctness bf the major concepts of the science of ore formation, established to so large an extent by the leaders of this notable group among whom Lindgren has been so eminent a figure. The geologists of the Survey have given and are continuing to give the service which can properly be expected of the Federal government. Their work, however, though of the greatest value in establishing the broad geological setting,

Jan 1, 1933

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700" I?. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent H²SO), filtered and charged directly to the doré furnace for refining to doré meta1. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1943