Search Documents

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By Arthur G. Levy, Henry M. Howe

$1. Introduction.—Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in fie familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal recrystallizing. The network in Fig. 22 and the parallel N.-70-E. lines in Fig. 21 are slip bands in copper. When plastically deformed metal is heated, certain parts of certain grains may twin, that is, their component crystalline units may rotate into a position, or more exactly into an orientation, symmetrical with the initial orientation and hence with that of the remainder of that grain. As seen in a microsection of a metal the twinned areas usually have parallel sides. The existence of twinning is recognized in metallic sections either by the presence of such parallel-sided areas differing in brightness from the adjoining metal, especially when seen under oblique light after etching, or more surely by the zigzagging of the slip bands which form when twinned metal is itself deformed again. Hence the usual procedure in developing twins is to deform plastically so as to cause the twinning tendency; to heat so as to allow the tendency to assert

Jan 1, 1915

By R. L. Loofbourow, Roger V. Pierce

THE degree to which our mineral requirements are being met by mining leaner, more complex or more remote deposits is indicated by developments during 1953. Heavy capital investment, skilled technical advice, planning, and able execution are requirements for the typical venture. Producers, faced with rising costs and with softer prices, are seeking improved mining and recovery. Developments in production of iron ore are typical of the course being followed in metal and nonmetal mining. Iron ore development in the U. S. is concentrated on the spectacular work with Lake Superior taconite, while in Canada new production is expected from Labrador and output from Steep Rock, Algoma, and Newfoundland is being increased. Shipment of iron will soon be made from Venezuela.

Jan 2, 1954

By Thomas Lane Carter

The history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers in the mines which the white men started. The Kaffirs of South Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribes in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country are much finer workmen than the degenerates from less favorable sections. It is universal in South Africa to speak of the Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a a boy," and in this paper the word " boy " is synonymous with Kaffir.

Jan 1, 1909

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By H. J. Ramey

A general solution is presented for the transient temperature distribution caused by radial movement of a cylindrical heat source through a homogeneous medium of infinite extent. This problem represents a highly simplified model of the movement of a combustion front during the thermal recovery of oil. Numerical solutions are presented for a heat source moving at a constant velocity, and a velocity inversely proportional to the radial location of the heat source. Numerical solutions are presented for both finite and infinite vertical thickness of the heat source, i.e., with and without vertical heat losses. The numerical solutions are used to estimate the fuel concentration needed to maintain a combustion front during the thermal recovery of oil. The sensible heat carried to the combustion front by the injected gas stream is discussed in regard to the fuel concentration. Numerical solutions for a heat source (combustion front) of finite vertical thickness indicate the field conditions that may be necessary to sustain the temperature of a combustion front above the ignition temperature of the fuel over considerable distances from an injection well. The results also have implications in regard to the quantity of heat required during ignition. The results of this computation apply to a highly idealized model of a thermal recovery process. But the results may be used as a guide in engineering consideration of the thermal recovery process. INTRODUCTIO N The thermal recovery of crude oil has received considerable attention since the publication by Kuhn and Kochl of laboratory and field tests of this method of oil recovery. Other publications2,3,4,5,6, since that time have dealt with various features of the thermal recovery of oil and have illustrated the extremely complex nature of this process. Vogel and Krueger7 described an electric analog computer designed to solve a moving heat source problem which was analogous to movement of a combustion front during the thermal recovery of oil. The heat source was maintained at constant temperature and was a cylindrical source of infinite height (no vertical heat loss) moving radially at either constant velocity, or at a velocity inversely proportional to the radial location of the heat source. Jenkins and Ramey2 presented analytical solutions to a similar heat conduction problem and pointed out the possible importance of vertical heat losses. The following presents a general solution to the transient heat conduction problem introduced by Jenkins and Ramey4 as well as numerical solutions for a wide range of conditions possibly similar to those that might exist during field operation of the analogous thermal recovery process. DESCRIPTION OF PROBLEM The problem considered in this paper is determination of transient temperature distribution caused by a cylindrical heat source of infinite or finite vertical height, moving radially through an isotropic medium of infinite extent. It is further assumed that the heat flux generated at the surface of the moving heat source may be a function of time such that the fuel concentration required may be constant, or permitted to vary, and that heat is generated at the surface of the heat source only. In regard to the thermal recovery of oil the assumption that heat is generated at the surface of the front is equivalent to assuming that the thickness of the combustion zone is infinitely small, or that the reaction rate between fuel and oxidant gas is infinite. The last assumption does not appear stringent. See laboratory information published by Martin, et al3 Under these assumptions the temperature distribution throughout an infinite medium caused by a heat source moving radially with an arbitrary velocity may be described by The heat generation function or heat flux at the surface of the source, +(t), is Note that the fuel concentration may be defined as a function of time. Eq. 1 is derived in the Appendix.

By K. E. Starling

Phase equilibria data were used to develop an equation-of-state correlation for complex hydrocarbon mixtures, thereby circumventing difficulties associated with use of pressure-volume-temperature data. Equilibrium phase data for two condensate reservoir fluids were used to determine equation-of-state parameters for hydrocarbons as heavy as C22H46 in a modified form of the Benedict-Webb-Rubin equation of state. Comparative tests of K-values from the resultant correlation were made with data for condensate reservoir, separator and gas plant absorber mixtures. Generally, for temperatures above OF and computed liquid densities below 0.55 Ib-mole/cu ft, the modified BIVR equation predicted K-values in close agreement with the experimental data. INTRODUCTION Accurate predictions of thermodynamic behavior for complex hydrocarbon mixtures are necessary for many calculations in the petroleum industry. Because of the relatively high cost of extensive experimental data, many correlations for prediction of phase behavior have been developed. Some of these, such as the correlation of K-values presented in the NGAA Equilibrium Ratio Data Book, are totally empirical.l Others, such as the Benedict-Webb-Rubin (BWR) equation-of-state method, are semitheoretical.2-4 Unfortunately, published correlation methods often do not accurately predict the phase behavior of complex hydrocarbon mixtures, principally because of inadequate representation of the effects of components heavier than decane. This paper presents a new approach to this problem in which basic equation-of-state relations including heavy hydrocarbon effects are applied. Equilibrium phase data for two condensate reservoir fluids containing hydrocarbons as heavy as C22H46 are used to correlate component K-values. The BWR equation was chosen as the prototype equation of state for this study because of its proven capability for accurately predicting phase behavior and thermodynamic properties of light - hydrocarbon mixtures? Research was directed toward development of BWR parameters for the heavy hydrocarbons and modifications of the mathematical form of the BWR equation for application to complex hydrocarbon mixtures. The new equation-of-state approach presented differs considerably from previous methods in that phase equilibria rather than PVT data are used for determination of equation-of-state parameters. It is an explicit approach since the parameters are determined directly from mixture data. As such, it does not encounter problems inherent in the implicit method used by Benedict, Webb and Rubin 2-4 and numerous other investigators—one in which mixture parameters were postulated to be functions of the pure component parameters. The pure component BWR parameters, in turn, were determined from experimental PVT data. This method has been limited to mixtures containing components lighter than decane because of lack of vapor phase PVT data. Studies have been reported in which BWR parameters have been determined explicitly from PVT data for binary mixtures.6-8 However, since small concentrations of heavier components have only a minor effect on PVT behavior, it is doubtful that these explicit methods would yield useful results for condensate systems. Ellington and Eakin9 have shown that the accuracy of K-values predicted by an equation of state developed from mixture PVT data probably would be more than an order of magnitude lower than the accuracy of the PVT data. On the other hand, an equation of state utilizing parameters developed from phase equilibria data should predict K-values with accuracy comparable to the accuracy of the experimental phase compositions. This work applies this explicit approach with the objective of improving hydrocarbon mixture phase behavior predictions. Results are evaluated by comparing predicted and experimental K-values at reservoir, separator and gas plant

Jan 1, 1967

By W. J. Carlson, S. M. Parmerter, I. Iwasaki

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates. It also deals with the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when an-ionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were affected most strongly by the level of starch, to a lesser degree by the pH, and virtually not at all by the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semitaconite could be readily attained with starch and calcium chloride. A previous article discussed some of the parameters that are important when various corn starches are applied to the soap flotation of activated silica from iron ores and to the flocculation of iron ore slimes.' Methods of solubilizing the starches and the molecular size after mechanical and thermal treatments, as inferred from the viscosity measurements, were shown to influence the adsorption characteristics on iron ores, and the residual concentrations of both calcium ion and starch in the pulp liquor were in direct correlation with the flotation and flocculation behavior.2-4 The present article summarizes the results of more recent tests conducted to ascertain the role of starches and starch derivatives in various phases of iron ore beneficiation. The scope of this investigation has been extended to include not only anionic and cationic flotation, but also the flocculation and filtration of iron oxide slimes, the selective flocculation and partial upgrading of semitaconites, and the flocculation and clarification of magnetite-taconite tailings —all problems that are of vital importance to the iron ore industry of Minnesota. By combining a practical approach with adsorption studies and by using single-mineral systems5 in these research efforts, it is believed that the ultimate goal of developing a suitable modification of starch structure may be realized. The topics covered in this article are limited to the empirical aspects of the research program on the depressant activity of starches and products in the cationic and anionic flotation of silica and of their role in flocculation, water clarification and filtration. ANIONIC SILICA FLOTATION In the soap flotation of activated silica from iron

Jan 1, 1970

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate

By Oren C. Baptist, Carlon S. Land

Laboratory research has been conducted to evaluute the effect of clay hydration on the permeability to gas of water-sensitive reservoir sands. Samples of a .sandstone containing trace amounts of montmorillonite and a sample of montmorillonite were .studied in the laboratory to detertnine whether swelling or dispersion was the cause of permeability reduction in these samples. Heliuin, containing various amounts of water vapor, was used to hydrate the clay minerals and to determine the gas permeability at various stages of clay hydration. The amount of water adsorbed by the samples using this method is small. The nonwetting-phase permeability at higher water saturations war investigated by saturating the with water and measuring the permeability to humid helium while decreasing the water saturation, Relative-permeability curves obtained from results of these procedures were used to estimate the effect of the swelling of trace amounts of mont/tlorillonite on the permeability of the .samples. Most of the damage to the permeability when reservoir sands containing trace amounts of montmorillonite are exposed to fresh water is due to dispersion and movement of clays. Blockage of pores by the increased volume of expanded montmorillonite is believed to result in permeability damage that is small in comparison to the observed damage to the samples tested. INTRODUCTION Studies have shown that permeability is severely damaged when sands containing only small amounts of montmorillonite are contacted by fresh water.15 When samples of sands containing large amounts of montmorillonite are placed in fresh water in the laboratory, these samples may completely disintegrate, forming an unconsolidated mass of larger volume than that occupied by the dry sample." In this case, it is apparent that the swelling of montmoril-lonite has destroyed the pore structure of the sand. If only a trace of montmorillonite is present in a sand. samples may remain intact when saturated with water, although the permeability to water is a small fraction of the gas permeability of the dry sample. Many workers in the field of water sensitivity have attributed this reduction in permeability to the blocking of pores and reduction of pore size by the increased volume occupied by expanded mont- niorillonite. if the sand contains a detectable amount of montmorill'onite or mixed-layer clay containing rnontmorillonite. Logically3 the smaller amount of montmorillonite present in a sand, the smaller should he the effect of montnlorillonite swelling on permeability; however, the quantity of montmorillonite sufficient to cause severe damage by swelling is not known. Although hundreds of samples have been tested in our laboratory, no correlation has been established between the amount of montmorillonite in samples and the permeability reduction caused by fresh water. To many petroleum engineers, the phrase "clay swelling" is synonymous with "water sensitivity", or "permeability reduction" implying that any formation damage due to the hydration of clays is caused by swelling. Although all clays adsorb water on their surfaces, montmorillonite is the only clay mineral commonly found in reservoir rocks which adsorbs water between intercrystalline layers, resulting in expansion of the clay particle. As montmoril-lonite swells, the first few layers of water adsorbed between platelets are strongly held and well oriented, and the montmorillonite retains its crystalline structure, although expanded. As swelling of sodium montmorillonite continues, the platelets become farther apart and the forces orienting the platelets in the crystalline structure become weaker, resulting in a less orderly orientation of platelets. In an abundance of water, small groups of platelets may become detached from the original monl-rnorillonite particle and may be dispersed throughout the water phase. Because of its swelling properties, sodium montmorillonite is very easily dispersed in water. Particles of other clay minerals. such as illite and kaolinite may also be dispersed in water. causing water sensitivity of sands not containing montmorillonite. The presence of an immobile layer of water adsorbed on the surface of clays has been considered a possible cause of the low permeability to water of dirty sands. Grim states that the thickness of the layer of immobile water held by sodium montrnorillonite is three nlolecular layers or 7.5 A (angstroms), with some orientation of water extending to 100 A. Assuming a very thick, immobile water layer adsorbed on the surface of a pore represented by a capillary tube, the maximum effect of the water layer on permeability can be calculated. Using a pore radius of 10 ' cm and an immobile water layer of 50 A. the calculation shows the permeability to be reduced only 2 per cent. Similar calculations can be used to show that the effect of electro-osmotic counterflow is of the same order of magnitude as that of bound water. The reduction of the permeability to water by either an immobile water layer

Jan 1, 1966

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to '85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By W. A. Jr. Slippy, E. P. Dahlberg, R. B. Reed-Hill

A large room-temperature mechanical-hysteresis effect under cyclic tensile loading was observed in zivconium specimens prestrained at 77°K so as to form large numbers of (1121) twins. The observed hysteresis loss was a maximum when the prestrain was just under 1 pct It also depended strongly on the maximum applied cyclic stress, but only moderately on loading rate and temperature (-72°to 100°C). The phenotnena have also been studied in terms of the elastic aftereffect where the data has been found to cotlforln closely to the functional relationship between strain and time, c = -RT/a In tank ft. t to)/Zr, for strains cts large as about 10-4 This eyication can be derived directly from the strain-rate equation There may be important commercial implications to the present discovery since it appears that within rather wide limits it may be possible to obtain any desired magnitude of damping capacity in zirconium melal. The damping propevties may also be given directional characteristics. It is shown that the observed anelaslic phenomena can he explained on the assumiplion that they are the resuilt of stress-induced twin-boundary movements in which the average twin increases its thickness by only a few percent. In polycrystalline zirconium, a grain is least favorably oriented for slip when its basal plane, containing the (1130) slip directions, lies nearly perpendicular to the principle normal stress. Mechanical twinning is favored by this orientation and under simple tensile deformation at room temperature the primary twinning mode is {1012).' The (1012) twinning shear is small (0.17) so that, during deformation, twin growth does not greatly enhance ductility. At 77°K, on the other hand, the predominant twinning mode shifts to {1121), and many thin (1121) twins can form at small strains.' Twins thus nucleated can grow readily during subsequent room-temperature deformation and permit easy deformation in unfavorably oriented grains. In addition, the (1131) twinning shear is large: 0.63. These facts have lead to a process' for greatly improving the room-temperature ductility of zirconium when it contains a sizable fraction of grains with basal planes nearly normal to the stress axis. Optimum results are obtained by slightly less than 1 pct prestrain. The effect is large so that a 50 pct elongation increase is readily attained. A large room-temperature mechanical-hysteresis effect has also been observed in zirconium specimens prestrained at 77°K. The present paper is concerned with some aspects of this effect which the experimental observations strongly indicate is primarily the result of strain-induced {1121) twin-boundary movements. This clearly suggests that mechanical twins formed by plastic deformation can cause anelastic effects similar to those previously observed2 for annealing twins and twins associated with phase transformations. EXPERIMENTAL PROCEDURES All specimens were prepared from arc-melted sponge zirconium plate stock as previously described,3 which has a preferred orientation with basal planes aligned parallel to and uniformly distributed around the rolling direction. Both lonti-tudinal and transverse tensile specimens, with axes parallel and transverse, respectively, to the plate rolling direction, were cut from this plate. In a longitudinal specimen most grains are favorably oriented for slip, while in a transverse specimen a large fraction are unfavorably oriented. Prestraining at 77°K was performed in two ways. In one, annealed zirconium plate stock was cooled in liquid nitrogen and then rolled in the transverse plate direction to strains varying from 0.5 to 12 pct. Cylindrical 1/8-in.-diameter by 1-1/4-in.-gage-length tensile specimens were machined from this material. In the other, previously machined tensile specimens were prestrained in tension at 77°K between 0.2 and 3.8 pct. Type FA 25-12 SR4 strain gages were cemented to all specimen gage sections. All tests were performed on an Instron testing machine of 10,000-lb capacity. EXPERIMENTAL RESULTS Fig. 1 shows a typical two-cycle room-temperature stress-strain diagram for a specimen prestrained 0.65 pct by rolling at 77°K. The maximum stress in both cycles was 14,500 psi. Note that in the first cycle the loading and unloading curves are unsymmetrical so that a residual strain, er, remains after unloading. In the second cycle the stress-strain curves form a nearly symmetrical hystere-

Jan 1, 1965

The Sub-committee on Coal Mining, since its appointment, has been collecting data about subsidences in coal mines in this country, and thinks that almost all of the available data about occurrences of this sort in bituminous mines has been collected. Similar data is being compiled for the anthracite regions, which it is hoped will be ready for the 1927 meeting. As most of the bituminous seams are nearly level, the records obtained give the problem in its simplest form, without complications due to the pitch of the seam. Copies of the questionnaire, Appendix A, were mailed to all of the coal operators' associations, to most of the large operating companies and to many engineers, with the request that any data on the subject be returned to the committee, or that advice of any subsidences known be given: the replies to most of the questionnaires were general, although some specific cases were given. Many of the companies were unable to reply to all questions, as they lacked the necessary data, but in nearly every case where accuratc data was available, it was cheerfully furnished, and any additional information requested was secured. All specific cases of subsidence were followed up by correspondence, and in several cases by personal inspection. Figs. 1 to 31 were made from the information furnished. Table 1 gives measurements of elevations taken in one case at intervals from October, 1913, to May, 1918. With one exception, where the evidence cannot be released on account of a lawsuit, it is believed that the cases submitted with this report include practically all that have happened in bituminous coal mining in this country of which actual measurements were secured. Some of these have been published by Young and Stoek,l and some have been secured from other publications. In collecting these data, the subcommittee had the Engineering Societies Library extend its bibliography to date; this list is given in Appendix B. To assist in the study of the problem, all of the subsidence literature in English was examined for cases in which spccific measurements were given, and the essential data for each case are shown in Appendix C.

Jan 1, 1927

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By Klaus Schwerdtfeger

The equilibria in the Cr-N system have been investigated in the temperature range 1100° to 1310°C by reacting chromium powder with Nz-Hz gas mixtures. The solubility of nitrogen in chromium in equilibrium with chromium subsitvide ("Cr,N") is given by Chromium subnitride is nonstoichiotnetric; its nitrogen content is always less than that corresponding to the formula CrzN. The lattice paranzeters of quenched samples have been measured; c, and a. parameters are found to increase with increasing nitrogen content. The growth rate of the subnitride layer on chromium plates was measured by a thermogravimetric technique, using a silica spring balance. The self-diffu-sivity obtained from the theoretical analysis of the parabolic rate constant is found to decrease with increasing nitrogen content, i.e., with decreasing vacancy concentration in the nitrogen sublattice. The intrinsic nitrogen diffuivity is derived from another series of rate measurements using "CrzN" plates; the intrinsic diffusivity, DN = 3.2 X 10-a cmZ sec-' at 1200 C, is found to be essentially independent of- the subnitride composition. The concentration gradient was measured in a chromium subnitride layer by the X-ray method and found to be consistent with the derived diffusivity value. TWO chromium nitrides are known to exist:' the nonstoichiometric subnitride "CrzN" and the nitride CrN. In the present work the kinetics of the formation of chromium subnitride from chromium and nitrogen have been investigated at 1100" and 1200°C. In additional experiments the relevant equilibria have been measured. The data are used to evaluate the diffusivity of nitrogen in chromium subnitride. Since chromium nitrides are often found in chromium-containing steels, the results are expected to be helpful in the interpretation of the chemical reactions between chromium steels and nitrogen. Equilibria in the Cr-N system have been determined by several investigators.2"3 The rate of nitriding of chromium was measured by Arkharov et a1 .' in ammonia in the temperature range 800" to 1200°C. The parabolic rate law was observed. Due to the undefined nitrogen activity of the ammonia atmosphere, it is dif- ficult to interpret these rate data theoretically. An additional difficulty arises from the fact that the two-layer scale consisting of CrN and "Cr2N" was formed at the temperatures below 1030°C. The rate of nitriding of technical chromium (95 pct) was measured by Zaks in nitrogen at -1 atm in the temperature range 800" to 1300°C. EXPERIMENTAL METHODS The chromium samples were reacted with Nz-HZ gas mixtures in a vertical tube furnace, wound with Pt-10 pct Rh resistance wire. The gas-tight reaction tube was of high-purity recrystallized alumina. In nitrogen solubility measurements the nitrogen content of chromium was determined by the Kjeldahl method, on samples quenched in the cold part of the furnace. The nonstoichiometry of the subnitride and the nitriding rates were measured thermogravimetrically using a sensitive (+0.1 mg) silica spring balance. For the equilibrium measurements samples of 1 g of chromium powder contained in high-purity alumina crucibles were used. In order to remove most of the oxygen and nitrogen impurities from the chromium, the samples were initially annealed in purified hydrogen until a constant weight was obtained. The chromium plates (approximate dimensions 2 by 1 by 0.08 cm) used for the rate measurements were machined from ingots obtained by arc-melting of iodine-processed chromium. According to manufacturers' specifications the purity of the chromium powder was 99.9 pct Cr and that of the iodine-processed chromium 99.99 pct Cr. Our own spectroscopic analysis of the chromium powder yielded 0.02 pct Fe, 0.05 pct Mn, 0.05 pct Si, and 0.02 pct Ti as major impurities with all the other detectable elements below 0.005 pct. The nitrogen partial pressure of the gas phase was controlled by mixing prepurified hydrogen and nitrogen with constant pressure head capillary flowmeters. Oxygen and water vapor were removed from the mixed gas by passing it through columns of platinized asbestos (450°C) and anhydrone. The gas flowed upward in the furnace with flow rates of 300 to 500 cu cm per min (25"~). Gas tightness of the furnace system was ensured by pressure checks at regular intervals. The furnace temperature was controlled electronically in the usual manner. The reported temperatures were measured with a Pt/Pt-10 pct Rh thermocouple and are estimated to be accurate within ±$C The X-ray measurements were made with a Debye-Scherrer camera and a diffractometer using chromium radiation {\Ka = 2.29092A). EQUILIBRIUM MEASUREMENTS The experimental results of the equilibrium measurements are contained in Tables I to In. Fig. 1 shows the solubility of nitrogen in solid chromium in the temperature range 1100" to 1310°C. In Figs.

Jan 1, 1968

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By Raymond L. Orr

Calorimetric measurements have been made of the heats of solution of gold axd indium in a number of liquid tin-rich alloys at a temperature of 705°K. Relative partial molar enthalpies of gold were determined as a function of dilute solute concentrations in the binary Au-Sn system and in the ternary Ag-Au-Sn and Au-In-Sn systems. Relative partial molar enthalpies of indium were determined for dilute solute concentrations in the In-Sn, Ag-In-Sn, and Au-In-Sn systems. Through application of the interaction coefficient concept introduced by Wagner and more recently extended by Lupis and Elliott, ualues have been obtained for the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. The results are inte@reted in terms of solute atom distributions through comparisons with the predictions of dilute solution models. INTEREST in the thermodynamic behavior of dilute liquid alloys stems from two primary sources. From a practical viewpoint, it is often of importance to know or to be able to predict the effect that one solute will have on the thermodynamic properties of the other solutes in a multicomponent system. Studies of dilute solutions may also be rewarding from the theoretical point of view. Some of the difficulties arising from the more complex interactions possible in concentrated solutions are avoided, leading to easier interpretations in terms of solutibn models and bonding energies. For example, in a binary alloy the limiting values of the partial molar properties of the solute represent the case for which each solute atom is completely surrounded by atoms of the solvent, and no other interactions are possible. Solute - solute interactions in dilute solutions are conveniently treated by the interaction coefficient concept of ~agner.' Using a Taylor series expansion for the logarithm of the activity coefficient, In yi, of a component, i, in a solution consisting of dilute solutes with atomic fractions xi, xj, xk, and so forth, in a solvent, s, and neglecting the second- and higher-order terms, Wagner obtained the expression: Where Wheyz is the limiting value of yi in the pure solvent, s. The interaction coefficients, e:, e:, and so forth, are defined by: Since yi is related to the excess partial molar Gibbs energy of component i by GfS = RT In yi, E: is re- ferred to as the "Gibbs energy interaction coefficient". Lupis and Elliott~ extended Wagner's treatment to the relative partial molar enthalpy, aHi, and the excess partial molar entropy, qS. They defined the enthalpy interaction coefficient as: and the excess entropy interaction coefficient as: leading to expressions similar to Eq. [I]: The three interaction coefficients are related by? The self-interaction coefficients, E:,qf,and at, represent the effects of interactions between atoms of component i in solvent s; €3, q{, and 03 represent the effects of interactions between i and j atoms in solvent s; and so forth. From the Maxwell-type relationships between partial molar quantities, it may be shown1'2 that e{ = ej, r}\ =tj), and ai - crj. Experimental determination of the interaction coefficients requires extremely precise measurements of the appropriate properties as functions of solute concentrations in very dilute regions. Few such data exist for intermetallic alloys, even for binary systems, because of experimental difficulties. This is especially true with respect to enthalpy data for dilute alloys. Examination of the compilation of data for binary alloys by Hultgren, Orr, Anderson, and ~elle~~ reveals that determination of limiting values of &fii(Xi =0) often requires extrapolations to infinite dilution from xi = 0.05 to 0.10. Direct measurements of the enthalpy interaction coefficient, qi, for multicomponent systems are virtually nonexistent. This quantity is of course subject to direct calorimetric measurement, but its determination must be limited to cases where high experimental precision is possible. The heats of solution of gold and indium in liquid tin can be measured with relatively high precision, which makes determinations of 73 involving these metals as the measured solutes experimentally attractive. This paper presents the results of such determinations of the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. MODELS FOR DILUTE-SOLUTION BEHAVIOR Random-Solution Behavior. In the quasi-chemical treatment of solutions, only nearest-neighbor bonds are considered, and a composition independent value

Jan 1, 1967

By Leon Eliel

TEN years ago .a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these. isolated bits of infor-mation can be ascertained, the message begins to take meaning.. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936