Search Documents

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By Arthur F. Taggart

The major portion of the work described in this paper was performed by R. W. Young, † a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at east 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation. In

Jan 1, 1918

By L. D. Jaffe, J. H. Hollomon

The effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained 011 tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

By Robert Maes, Robert de Strycker

The Fe-Ni-As phase diagram has been established by the study of about a hundred alloys, by microscopic observation, and by thermal analysis, with arsenic contents up to 50 pct. The iron and nickel arsenides present extensive solid-solution fields, owing to the substitution of nickel by iron and vice versa; the extent of the solubility field of each compound has been determined with an accuracy of ±1 pct. In the investigated range of compositions, the solidification reactions were established, and the temperatures of the invariant reaclions detevmined with a preciston of iZ°C in the most favorable and ±5°C in the least favorable cases. The isothermal lines of the liquidus surface have also been drazum, with an accuracy estimated at i5°C. Reactions in the solid state, which take place for the formation or the decomposition of certain phases , were investigated in detail. ThE constitution diagram of the Fe-Ni-As system is fundamental for the understanding of the properties of nickel speiss; these by-products of the extraction of certain nonferrous metals indeed often contain the three elements iron, nickel, and arsenic as main constituents. The Fe-Ni-As system has already been the object of earlier investigations. In 1932, Guertler and Savels-berg' have presented some elements of the ternary phase diagram, for arsenic contents up to 55 pct (all percentages in this paper are given in weight percent), including the vertical section FezAs-Ni&s2. This investigation is, however, incomplete and certain anomalies suggested the necessity to verify the results published by these authors: the section Fe2As-Ni5AsZ, for example, is presented as quasi-binary, with a field of complete miscibility in the solid state, even though these compounds do not have the same structure. Recently, ~useck' established an isothermal section at 800°C in the Fe-Ni-As system by X-ray diffraction and microscopic examination of water-quenched alloys. These techniques are sometimes inaccurate for the determination of the fields where alloys are liquid at the investigated temperature, and they may lead to erroneous conclusions when a compound exists at the investigated temperature but is not stable at room temperature and cannot be maintained by quenching. LIMITING BINARY PHASE DIAGRAMS The Fe-As constitution diagram has been the object of several investigations which have been reviewed by Hansen and Anderko.3 For the Ni-As phase diagram, a recent study has been effected by Yund.4 In this system, Heyding and calvert5 have determined the existence of a compound of unidentified structure at arsenic contents slightly higher than those corresponding to Ni5As2 and at temperatures lower than about 200°C; by analogy with iron and cobalt arsenides, this compound could correspond to the formula Ni2As, as suggested by Kulle-rud; although this is not definitely established. In the region of arsenic contents from 35 to 55 pct, Fried-rich7 detected anomalies in the solidification reactions; an interpretation of these anomalies was given by Hansen ,8 which assumed that the solidification reactions in practice are not in equilibrium, but are meta-stable. The main features of the Fe-Ni constitution diagram are the existence of a complete miscibility field, at least at high temperatures, for the fcc phase (which will be designated by My in the remainder of this work) and of a limited solubility field for the bcc phase (designated by Ma). EXPERIMENTAL METHODS The fundamental technique used in this investigation was microscopic observation, which allowed the determination of the reactions occurring during solidification of the alloys, and possible reactions in the solid state.

Jan 1, 1968

By Arthur Crowfoot

Page IntRodUction ................... The Round Table in Lake Superior Practice .........420 Early Use of Revolving Round Table in Butte District...... Use oF the Round Table at GREat Falls foR Sand-Slime Feed ., . The Round Table for Fine Slime........,.... Construction of Slime Plant at Great Falls..... '..... 424 Tests on Wood, Linoleum, and Cement Decks.........426 Central Feed Apron Removed ....'......... Re-treatment of Round-Table Tailing........... Determination of Conditions for Round-Table Treatment of Slimcs ... 430 Variation in Slope of Round-Table Deck........ ,... The Steel-Frame Cement-Deck Round Table ........ Tests on Cement and Canvas Dock Surfaces ..: ..... Conoidal Deck Round Tables............. Results with Sand-Slime Feed on Conoidal Deck....... Conclusions from Preliminary Tests on Conoidal and Conical Decks ... 446 Discussion of Results of Four-Day Test on Conical and Conoidal Decks . 452 Discussion of Results of Eight-Day Test.......... Qualitative Sampling of Concentrates Across Conical Deck.... Summary of Slime-Plant Practice............ Suggested Flow Sheet for Slime Classification and Treatment.... Conclusion...................467 Introduction The principal object of this paper is 60 presest, data on the development of the revolving convex round table as a concentrator for the through 0.07-mm. slimes from the ores of the Butte district, although some brief notes on the earliest recorded use of this type of concentrating table in the ore-dressing plants of the Lake Superior region and of the Butte district are also presented. The revolving convex round table belongs to the class of concentrating tables known as film-sizing. tables, these tables using the relative transporting power of a film, or thin sheet of water, as it flows over a quiet inclined surface, to separate the minerals of a sorted product. The grains of heavy mineral move down the slope of the table deck slowly, or, in some cases, not at all, after the initial force of the feed entry VOL. XLIX.—27

Jan 1, 1915

By G. Meyrick, H. W. Paxton

Observations on the tensile deformation of single crystals of austenitic stainless steels as a function of composition, orientation, and temperature are described and compared with relevant data for other alloys. Crystals free from second phases show sharp yield points followed by Lüders' extensions of up to 20 pct. The critical resolved shear stress is strongly temperature-dependent increasing fourfold between 423O and 77°K. A temperature-independent low rate of hardening follows the Luders' extension and is frequently associated with overshoot. Unlike pure metals where Proficse cross slip usually occurs at the end of linear hardening, this stage is terminated either by cross slip or by slip on the conjugate system, the particular node apparently depending upon initial orientation and composition. The presence of 6 ferrite or martensite has a profound effect upon the magnitude of the yield stress and the shape of the stress-strain curve. In experiments on transgranular-stress corrosion cracking of austenitic stainless steels in boiling magnesium chloride, several workers1'2 have shown that increasing amounts of nickel tend to reduce the probability of specimen failure. Reed and paxton3 have observed in single crystals that the macroscopic crack plane changes as the nickel content is increased. For 18 pct Cr-8 pct Ni, the crack plane is sensibly perpendicular to the applied tensile stress; for 20 pct Cr-20 pct Ni the crack plane is (100). The average crack-propagation speed is much lower in the 20 pct Ni crystals. Furthermore, the possible importance of stack-ing-fault energy in nucleation and growth of cracks has been suggested by a number of workers. While the general effect of variations in stack ing-fault energy appears to be quite well-correlated with observed variations in cracking characteristics, each of the theories assigns rather different detailed reasons for these effects. Because the stack ing-fault energy of austenitic steels is believed to be increased with increasing nickel content, and because some theories of trans-granular cracking postulate a mechanical stage in the crack propagation (rather than relying entirely on electrochemical solution), it appeared to be of some interest to investigate the mechanical properties of a series of different compositions of aus-tenite single crystals. These experiments were considered of intrinsic value in view of the relative scarcity of such data on fcc alloys. This paper gives the results of some experiments carried out with this aim in mind, and suggests various 'other experiments which may be helpful in future studies. The experiments are also of interest in view of the recent interest in obtaining higher-strength steels by control of the imperfection content of austenite; although the compositions are not directly comparable, the results are still probably valuable. Comparisons with experiments on other fcc alloy crystals are made where possible to see how well the general pattern of behavior is understood. EXPERIMENTAL PROCEDURE The alloys used in this investigation were vacuum-melted heats of nominally 20 pet Cr-20 pet Ni-60 pet Fe, 20pctCr-16 pct Ni-64 pct Fe, and 20 pctCr-12 pet Ni-68 pet Fe.* Analyses of the material are

Jan 1, 1964

By Richard Hunt

BINGHAM has produced 6 per cent. of this country's copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham's silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. Bingham is on the eastern flank of the Oquirrh range 30 miles south-west of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads.. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep-an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century.

Jan 3, 1924

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By I. R. Kramer

The stress associated with the high-dislocation layer at the surface of deformed aluminum crystals was measured by progressively polishing the specimen and determining the change in the initial flow stress when the specimen was reloaded. This surface stress increased linearly with strain in the Stage II and Stage III region. The depth to which the high-dislocation layer extends was found to be 0.0025 in. The influence of the surface layer on Stage I is discussed and it is shown that Stage I ends when, on the secondary slip system, the difference between the applied stress and the opposing stress due to the surface layer is equal to the critical resolved shear stress. In previous papers'-3 it was shown that the surface exerts a pronounced effect on the plastic-flow characteristics of metals. For fcc metals it was possible to increase the extent and decrease the slope of Stages I and II and decrease the work-hardening coefficient of Stage II by removing the surface of the specimen continuously during the deformation process.2,3 More recently,L it was shown that the activation energy for plastic deformation and the activated volume were also influenced by the surface. These changes were related to the existence of a high concentration of dislocations in the region near the surface of the deformed specimen and it was concluded' that the effective stress, T, acting on a dislocation was T = Ta-Ti-Ts [1] where 7, is the applied shear stress, Tj is the internal stress, and TS is the stress associated with the surface region containing the high concentration of dislocations. From Eq. [I] it is seen that the effective stress, 7, acting on a dislocation is a function of 7,. Therefore 7, becomes important in any description of the work-hardened state. In this paper the value of 7, as a function of strain and its variation with depth are reported for aluminum single crystals. In particular, it will be shown that the end of Stage I occurs when the net stress, 7, on the secondary slip system is equal to the critical resolved shear stress. To measure Ts, single crystals of aluminum were deformed in tension to various strains, whereupon the load was removed and a known amount of metal was removed by electrolytic polishing. The differ- ence between the final flow stress before the specimen was unloaded and the initial flow stress upon reloading is designated as ?Tp and is the decrease in the stress due to the removal of the surface layer in whole or in part. The value for Tp is taken equal to -Ts. EXPERIMENT PROCEDURE The details of the tensile apparatus, method of electrolytic polishing, and crystal preparation were the same as those used previously,1"3 The single crystals were 1/8 by 1/8 in. in cross section with a 3-in. gage length. The initial purity of the aluminum was 99.997 pet. The specimens were held in vacuo at temperatures 50°C below their melting points for 16 hr and furnace-cooled. Just prior to the application of the tensile stress the specimens were electrolytically polished to remove 0.004 in. from the thickness. This latter operation was conducted after the specimen was placed in the tensile apparatus. The tensile tests were conducted at a strain rate, i, of 10"5 sec-' and a temperature of 3°C. The aluminum crystals used for the determination of 7, are designated A1-3-12 and A1-116. The orientation of the various crystals used throughout the investigation is shown in Fig. 1. The ?Tp values for specimens A1-3-12 as a function of Ax were determined mainly at four strain levels, i.e., ? = 0.0217, 0.0381, 0.0593, and 0.075, where Ax is one half of the total reduction of the thickness after polishing and ? is the re-

Jan 1, 1965

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By J. A. Harrison

The physical composition of coal and the distribution of its physical constituents will partially determine the efficiency of the process chosen for coal preparation. Distribution and concentration of coal macerals will, to a degree, be controlled by preparation processes. A number of preparation processes have been evaluated to determine this interrelation. These evaluations will help provide information needed for the production of coal that meets definite petrographic composition specifications. etrographic composition and degree of coalifica-tion of coal can determine the choice of cleaning processes and equipment used in coal preparation. The purpose of this paper is to present data on studies of the preparation processes of breakage, sizing, cleaning, and blending and to show the effect coal's petrographic composition has on these processes. Herrin (No. 6) and Danville (No. 7) Coals from Illinois were used in these tests. Nomenclature used herein is that approved in the Glossary of the International Committee for Coal Petrology,' based primarily on the Stopes-Heerlen system of classification2 and used in coal petrography laboratories throughout the world. BREAKAGE TESTS Breakage tests of Illinois coals related to petrographic composition have been conducted at various times at the Illinois State Geological Survey. These tests have been classified under two headings -impact tests and compression tests. Impact tests, as the name implies, consisted of breaking the coal by a sharp, sudden force. Impact tests were further divided into fall tests and block tests. Compression tests consisted of applying a constant pressure on a piece of coal until the coal fractured.

Jan 1, 1963

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By Max Mason

In 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which automatically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1929

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.' Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970