Search Documents

By E. I. Gordon

The electronic pickup tube is the image-to-video signal-converter or transducer in tele vision-like systems. Images may relate to visible light or IR excitation as in conventional TV systems, X-ray excitation as in some medical and production control applications, or electron excitation as in electron microscopy. The latter process is also important in some forms of light or X-ray sensitive pickup tubes as an intermediate step. In virtually all of these devices the image ends up as a stored charge pattern on a suitable target electrode and the video signal is created by periodically scanning the target with a low energy electron beam and removing the stored charge. In a major group of tubes radiation induced conductivity creates the charge pattern. In others, photoemission is used. In this paper an attempt is made to illuminate some of the device requirements placed on materials exhibiting radiation induced conductivity, some of the materials and techniques that are used, and the problems. The emphasis will be on visible light and IR sensitive targets although some attention will be given to X-ray and electron imaging. Photoconducting films as well as diode arrays will be discussed. ELECTRONIC pickup tubes find their greatest use in commercial, entertainment television, and in industrial and educational closed-circuit television. Video telephone systems, such as AT&T's PICTURE-PHONE System will become eventually the greatest user. Military use is also very important. Nevertheless the use of electronic pickup tubes in technology, science, and medicine is assuming ever greater relevance and demands the greatest diversity and perfection in the pickup tube art. Commercial television and closed-circuit television use requires visible light response, high resolution, low lag, and uniform response. Video telephone use requires the same plus extreme reliability, stability, and low cost. Military use emphasizes, in addition, sensitivity, IR response, and ruggedness. (Devices for far IR response will not be considered here.) The use of pickup tubes in medicine and biology emphasizes UV response for microscopy, X-ray response for radiology, and energetic electron response for electron microscopy. Astronomy and nuclear physics demands low light level response, storage ability, and resolution (here the tube is a successful replacement for film). The interested reader might profitably read Advances in Electronics and Electron Physics, vol. 12,' 16,2 and 22A3 and 22B4 for detailed discussion of the use, properties, and technology of electronic pickup tubes. In general, because of the importance of these uses, none of the above properties will be ignored. Nevertheless attention will be restricted to only those imaging devices, called pickup tubes, using a scanning electron beam to dissect the image with a resulting video signal for conventional CRT display. However pickup tubes have become so complex that many of them include components such as image in-tensifiers which would be normally excluded by this restriction. Thus some of the other imaging devices will not be ignored entirely. We will first review the fundamental elements and physical phenomena involved in modern electronic pickup tubes, then the relevant materials and some of the material problems and then an interesting goal yet to be achieved. REVIEW OF PICKUP TUBE PRINCIPLES In all modern television systems using pickup tubes there is an interval called the frame interval, during which the incoming radiation flux is allowed to produce a cumulative effect in the form of a stored charge pattern which is a replica of the radiation image, and a scan interval during which the stored charge pattern is converted into a video signal. The frame interval bears no fixed relation to the scan interval and may be shorter or longer. In conventional, real time television the scan interval including retrace is identical to the frame interval. Integration and storage is the key to the sensitivity of modern pickup tubes, in contrast to earlier tubes such as the image dissector. At equivalent light levels and without integration, the number of photons contributing to the video signal in the image dissector is lower by a factor approximating the number of picture elements in the displayed image, a number of order 10. Statistical fluctuations in the number of contributing photons represent a serious limitation to the attainable signal to noise ratio, resolution and contrast. As a result considerably greater light levels have to be used then in targets which integrate over the full frame period. Thus the crucial elements, common to all modern pickup tubes, are the charge storage surface and the scanning electron beam which is incident on the charge storage surface at very low energy. These are shown in Fig. 1(a). The charge storage insulator is generally very thin with a thickness of several microns or less. The surface of the insulator is held near cathode potential. The backplate potential is held at cathode potential or at a small positive voltage relative to cathode. The combination of storage insulator and backplate electrode is commonly called the "target". In the absence of incident radiation flux the electron beam scans over the storage surface depositing negative charge uniformly over the scanned part of the surface by virtue of the fact that the effective secondary

Jan 1, 1970

By J. C. Melrose

The contact angle is one of the boundary conditions for the differential equation specilying the configuration of fluid-fluid interfaces. Hence, applying knowledge concerning the wettability of a solid surface to problems of fluid distribution in porous solids, it is important to consider the complexity of the geometrical shapes of the individual, interconnected pores. As an approach to this problem, the ideal soil model introduced by soil physicists is discussed in detail. This model predicts that the pore structure of typical porous solids will lead to hysteresis effects in capillary pressure, even if a zero value of the contact angle is maintained. The model is generalized to situations in which the contact angle takes on values between zero and 40 degrees. For the imbibition branch of the capillary- pressure function, the model predicts a considerable departme ftom the usually assumed cos 0 relationship. In fact, according to the model, it is possible that a displaced wetting phase will not be able to reimbibe, even when the contact angle does not exhibit hysteresis. INTRODUCTION The subject of capillarity in porous media has long been of interest in many branches of engineering and applied science. The earlier investigators were those concerned with the physics of soils. 1-5 More recently, petroleum engineers and others dealing with the problems of petroleum production from reservoir rock have given much attention to the subject.6-10 Also, important additions to the literature of capillarity have been contributed from the field of chemical engineering.11-12 These attest to the wide range of industrial applications in which capillary phenomena play a role. The present paper is concerned with the role which wettability plays in capillary action in porous media. As is well known, capillary-rise (or capillary pressure) phenomena have frequently been interpreted with the aid of a model employing the concept of a cylindrical capillary tube. This approach has enjoyed a certain degree of success in correlating experimental results.13 The generalization of this model, however, to situations which involve varying wettability, has not been established and, in fact, is likely to be unsuccessful. In this paper another approach to this problem will be discussed. A considerable literature relating to this approach exists in the field of soil science, where it is referred to as the ideal soil model. Certain features of this model have also been discussed by Purcel114 in relation to variable wettability. The application of this model, however, to studying the role of wettability in capillary phenomena has not previously been attempted in detail. In the present paper, additional features of the model are introduced. These features are critical in determining the quantitative behavior of the model. GENERAL FEATURES OF CAPILLARY HYDROSTATICS BASIC PRINCIPLES When the interstices of a typical porous solid are occupied by two or more immiscible fluid phases, the fluids are microscopically commingled. Hence, fluid-fluid interfaces are found within a certain fraction of the pore openings. The fundamental equation of capillarity specifies the configuration of these fluid-fluid interfaces. This is known as the Laplace equation, when derived from mechanics, and as the Gibbs-Kelvin equation when derived thermodynamically.15 Given two fluid phases, a and ß, in hydrostatic equilibrium, the Laplace equation states that the respective fluid pressures in regions close to the interface are related by Here oaß is the surface or interfacial tension and rl and r2 are the principal radii of curvature of the surface or interface. The pressure difference, Pa-Pß, is the capillary pressure, PC. As Buff15 has shown, Eq. 1 states the condition for hydrostatic equilibrium within the two-phase confluent region, which is referred to as the interface. It thus can

Jan 1, 1966

By C. E. Ells, A. Sawatzky

The effect of neutron irradiation on tensile properties of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy has been evaluated for integrated neutron fluxes up to 3 x 1020 n per sq cm (E > 1 Mev). Specimen temperature during irradiation was normally 300°C. The material was studied both in annealed and in quenched and aged conditions. When the alloy (fab-ricatedfrom sponge zirconium) is quenched from a temperature =40°C below the a + ß/ß transformation and aged 6 hr at 535oC, neutron irradiation up to the maximum studied has little effect 071 reduction in area, although there is a drop in uniform elongation and the yield strength is increased by = 25 pct. Conversely, irradiation of the alloy in an annealed condition can result in much greater changes in properties, with yield-strength increases of up to 200 pet. The dose dependence of irradiation hardening obeys the saturation equntion proposed by Makin and Minter to explain hardening in copper and nickel: Act = C[1 - exp(-Døt)/1/2 A rnodel is proposed to explain the effect of niobium content and metallurgical condition on irradiatiotz behavior. THE Zr-Nb alloys form a class of material susceptible to marked strengthening by quench and age heat treatment. With niobium concentrations as low as 2.5 wt pet, strengths can be developed which are double those of annealed zircaloy-2.1 Since the neutron-capture cross section of the Zr-2.5 wt pet Nb alloy is nearly identical to that of Zircaloy-2, significant gains in power-reactor neutron economy could be obtained by replacing stressed in-reactor components of Zircaloy-2 with the heat-treated Zr-Nb alloy. When the solution heat-treatment temperature is in the high (a + ß) phase, then the tensile properties of the quenched (and aged at 500°C) material have been shown to be relatively insensitive to neutron irradiation.1-3 Addition of small quantities of copper to the binary Zr-2.5 wt pet Nb alloy gives a useful reduction to the corrosion rate in air and carbon di- oxide,&apos; and a ternary alloy of composition Zr-2.5 wt pet Nb-0.5 wt pet Cu was chosen for one component in the Douglas Point Reactor. This application utilizes both the corrosion resistance to a moist air-carbon dioxide environment and the strength developed by a quench and age heat treatment. By suitable choice of solution heat treatment and aging temperatures, tensile properties of the ternary alloy can be made nearly identical to those considered as optimum for the binary alloy. One effect of the copper addition, however, is to give marked changes in the aging kinetics of the alloy.&apos; For this reason, it appeared that neutron irradiation might promote overaging in the ternary alloy, particularly at the elevated service temperature (=300°C). This paper describes the effect of neutron irradiation on the tensile behavior of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy in several metallurgical conditions pertinent to its use as a reactor material. The metallurgical conditions included those for which aging occurs in the unirradiated material, and fully annealed conditions for which a higher degree of thermal stability could be expected. 1) EXPERIMENTAL Two batches of alloy were used, both made from sponge zirconium. The fabricator&apos;s analysis of principle constituents showed no significant difference between the two batches, Table I. The rod material was rolled to 1.5 in. diam, and then swaged to final sizes of 0.5 to 0.375 in. diam at nominal temperatures of 785" and 625°C for the AM and AS batches, respectively. Subsequent hydrogen analyses at CRNL confirmed that the hydrogen concentration of the as-received rod was indeed <20 ppm. However, it was found that the (a + ß)/ß transus for the AM material was approximately 25°C lower than that of the AS material, indicating rather more difference in oxygen concentration than given in Table I. Except for a small difference in yield-point behavior, the tensile prop-

Jan 1, 1965

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-&apos; proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible &apos;References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, &apos;pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.&apos; However, the components which are strongest in the recrystallization texture are in this range.&apos;________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,&apos; 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.&apos;~-&apos;~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.&apos; In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2&apos;13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,&apos;~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.&apos; state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

By Ralph D. Parker

The Frood mine (Fig. 1) is 2½ miles north of Sudbury, at a general elevation of 1000 ft. above sea level. It includes the original Frood location, which was the No. 3 mine of the Canadian Copper Co., and the adjoining Frood Extension, which until 1929 belonged to the Mond Nickel Co. Mine Openings The mine is operated from two vertical shafts and one underground incline shaft. No. 3, for men, supplies and ore, is a vertical six-compartment shaft in the footwall of the south mining area and extends froin surface to a depth of 3045 ft. No. 4 is a vertical three-compartment shaft, 2500 ft. north of No. 3 and adjacent to the north mining area. It extends from surface to a depth of 3345 ft., and is used exclusively for hoisting ore. No. 5 shaft, inclined at 65&apos; to the horizontal and of three compartments, is near No. 4 and extends from the 2600-ft. level to 77 ft. below the 3100 level. It is used for development below the 2800 level. The ventilation shaft, No. 1, with which this paper is directly concerned, will be described fully in the following pages. Mining Methods The orcbody is laid out in 80-ft. sections at right angles to the gcneral strike and numerically indicated from the southern extremity toward the north. Each section consists of a 45-ft. stope and a 35-ft. pillar, extending the full width of the orebody. Pillars and stopes are superimposed from level to level. The present mining territory is divided into two vertical areas, a north and a south area. Both areas have the same number of stopes on each level, the two areas being separated by 10 sections to be mined later. In a few instances, at the ends of the south area, where the orebody has narrowed, longitudinal stopes are used, of more than the usual 45-ft. width. It will thus be seen that mining operations hare been concentrated in two relatively small areas, offering

Jan 1, 1934

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,&apos;9 it hydraulic horsepower and jet impact force,&apos; each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.

By W. L. Penberthy, H. J. Ramey

Experimental work on the combustion oil recovery process has consisted of both laboratory and field studies. Although field experiments are the ultimate test of any oil recovery process, they are costly, time consuming and difficult to analyze quantitatively. Laboratory combustion tube experiments can be opertzted far more rapidly and cheaply, but are subject to scaling and interpretation problems. This paper points out some important design problems, operational criteria and considerations in2portunt to interpretation of results. An analytical hcut model of movement of a burning front axiully along a cylinder with heat loss through an annular insulation was developed. The result was used to identify steady-state temperatrrre distributions both ahead of and behind the burning front, with and without heat loss. Results indicate potential operating limitations on the minimum burning front rielocity (or air flux) which may be used for any given combustion tube. Results also enable estimating the effective thermal diffusivity and over-all heat loss from experimental data and thickness of the brnning zone. Resu lts of operation of a combustion tube constructed recently verify this preliminary theory in the region immediately ahead of and behind the burning front surprisinRly well. INTRODUCTION Many field and laboratory studies of the forward combustion oil recovery process have been conducted since the early publications of Kuhn and Kochl and Grant and Szasz2 in 1953 and 1954. In view of the complex and costly nature of this type of investigation, it is not surprising that no complete theory of the nature of the forward combustion Drocess is yet available. However, gross effects are understood well enough that reasonable design procedures are available for planning field operations. Nelson and McNeil 3,4 have published two comprehensive papers concerning design procedures. One major consideration in planning field operations is the fuel concentration at the burning front. Fuel concentration controls air requirements — an important cost factor in forward combustion. Although fuel concentration can be estimated from field test results by various methods, results are subject to great uncertainty in view of natural limitations on experimental observations. Nelson and hlcNeil4 recommend that fuel concentration be determined from laboratory combustion tube studies. Fuel concentration is only one of many important factors which can be studied by combustion tube experimentation. An obvious goal of imporrance must be development of a comprehensive theory of the forward combustion process. If a theory of this process can be established which matches controlled laboratory experimentation, it should be possible to apply this theory to field operating conditions with some confidence. Laboratory combustion tube studies have already yielded important information concerning the combustion process. However, details concerning the design, construction and operation of combustion tubes are rare. Combustion tubes used by various investigators vary in size, length and mode of operation. Therefore, one purpose of this paper is to present considerations important to design, construction and operation of a combustion tube. In regard to previous combustion tube studies, attention is called to Refs. 1 through 9. These references describe a wide variety of equipment types and present a great deal of pertinent experimental data. In general, combustion tubes usually consist of thin-walled stainless steel tubes containing an oil sand pack mounted within a pressure jacket. Provisions have often been made to heat the tube ex tern a lly by separately controlled heaters to reduce heat losses. This step usually permits operation at low air fluxes (air rate per square foot burning front surface) similar to those encountered in field operations. Burning is usually conducted from the air inlet end of the tube to the outflow end. The tube orientation used has been vertical or horizontal. For vertical tubes, burning has been conducted vertically downwards. As a result of laboratory studies, many of the

Jan 1, 1967

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By H. D. Outmans

The paper presents a theoretical approach to the drilling problem based on rock mechanics and drilling fluid hydraulics at the bottom of the hole. The volume of the fractured rock around the vevtically penetrating bit tooth is expressed as a function of the tooth pressure, included tooth angle, drilling fluid pressure and formation characteristics on the assumption that fracturing is preceded by plastic flow. This assumption is verified by comparing the stress-strain state in the rock around the tooth to that in equivalent tri-axial compression tests described in the literature. An expression similar to the above is derived for the tooth penetration in the cuttings which have been retrained at the bottom. Combination of these two expressions leads to a relation between depth of tooth penetration in the virgin rock, the amount of cuttings retained and the other variables. By relating the cutting volume to the drilling rate, the hydraulic bit horsepower and the drilling fluid pressure, it is possible to arrive at formulas which express the drilling rate for viscous or turbulent flow at the cutting surface, for instant clearance, for retained cuttings, or for false tooth foundering as functions of such variables as the drilling fluid pressure, hydraulic horsepower at the bit, rotary speed and bit weight. Plotting the results as drilling curves and comparing them to published field and laboratory data justify the conclusion that the drilling model presented in this paper approximates the actual mechanism. The drilling curves serve to explain some characteristic features of the rotary drilling operation, and the equations may be used for numerical evaluation of the effect of changes in the magnitude of some of the variables on the drilling rate. INTRODUCTION Published laboratory data have established that consistent and relatively simple relations exist between the drilling rate and any one of the important variables. For instance, the drilling rate usually increases at an increasing rate with the bit weight. It increases at a decreasing rate with the rotary speed, decreases at a decreasing rate with increased drilling fluid pressure and plots as an S-shaped curve against the hydraulic horsepower at the bit. This relative simplicity seems difficult to understand considering that the drilling mechanism is a continuous process of generation and removal of innumerable individual cuttings, under different conditions for each. On the other hand, the drilling rate (although determined by this complicated process) only expresses the average rate at which cuttings are produced and cleared away. Ignorance of the drilling mechanism as far as individual cuttings are concerned, therefore, does not exclude the possibility of arriving at a concept of the drilling rate provided the mechanism is properly evaluated for the average cutting. It then may be concluded from the first sentence that this concept also should be rather simple in its final form, although not necessarily in its derivation. Two aspects of the drilling mechanism are difficult to evaluate — (1) the effect a penetrating drilling fluid has on the stresses around a bit tooth entering the formation and (2) the volume of rock fractured by a penetrating tooth which moves both vertically and horizontally. Thus, the scope of this paper has been limited to an evaluation of the drilling mechanism in formations which have a low permeability and are drilled with hard-formation bits. In the following sections, the drilling mechanism is analyzed in three steps. First, the effect of tooth pressure on the volume of fractured rock around the tooth is evaluated, assuming initially that the bottom of the hole is free of cuttings and, then, determining the effect of a layer of these cuttings. In the second section, the thickness of this layer is related to the drilling rate and the chip clearance time, and the latter to the hydraulic horsepower at the bit under conditions of laminar and viscous flow at the cutting surface. In the third section. the previous results are combined with the rotary speed into drilling equations which are then plotted and compared to experimental drilling curves. This section also contains some numerical examples of drilling rate computations. Some mathematical details are given in the appendixes. Finally, it should be mentioned that, although some drilling equations are already available, these equations (with the exception of one&apos; which attempts to relate drilling rate to drilling fluid pressure) are all mathematical expressions for observed laboratory data; none considers the effect of delayed drill-cutting removal, an essential feature of the drilling mechanism.

Jan 1, 1918

Jan 6, 1951

By J. Bartrum, I. S. Schache, H. J. Dobrowolski

Developments in milling of silver/lead/zinc ores at Mount Isa since 1970 have followed broad objectives to improve metallurgical performance and to increase plant capacities for Mount Isa ores treated through the No. 2 Concentrator. Pilot Plant work on a range of Hilton ores has led to detailed feasibility studies on application of heavy media pre-concentration and zinc reverse cleaning techniques on Mount Isa ores. The role of these developments in achieving metallurgical goals and effects of different ore characteristics are discussed.

Jan 1, 1977

By Waldemar Lindgren

THE purpose of this paper is to present certain facts relating to Cordilleran differentiation and metallization. Theoretical discussions concerning the exact modus operandi of differentiation, the causes that led up to it, and the original distribution of the magmas have been omitted because the author feels that his knowledge is deficient. These subjects have been adequately treated in the admirable works of Iddings, Daly, Harker, Tyrrell, Shand, and Wolff. The facts here set forth seem to indicate that differentiation and metallization form one continuous process during the eastward movement of the magmas, culminating in the alkaline province of the eastern border of the Cordilleran Ranges.

Jan 1, 1933

Jan 1, 1950

By Russell Salter, Edwin J. King

SINCE 1950, when perhaps two or three cyclones were being tested in Arizona, the number in use has grown to about 100. Most of these have come into operation within the last two or three years, and according to information supplied by various mining companies, the number will continue to grow for several years more. In mills that have been recently constructed, cyclones dominate the fine classification field, removing grit from lime slurries, producing smelter flux, reducing concentrate thickener overloads, classifying molybdenite in grinding circuits, and conditioning flotation feed. Four major copper companies are now testing cyclones in primary grinding circuits, and one concentrator soon to begin operation will classify entirely with cyclones. In at least two instances these versatile machines have been given a vital role in the construction of tailings disposal systems.

Jan 8, 1957

By Eugene Stebinger

PAGE Introduction.............. 890 Position oF Montana in the Western Coal Province*..... 890 Montana&apos;s Total Coal Tonnage.........891 THe Coal-BearINg Formations,........891 General Statement............. 891 Kootenai Formation............ 895 Eagle Sandstone............896 Judith River Formation............ 896 Homethief or Lennep Sandstone.........897 Lance Formation..........• 897 Fort Union Formation............ 898 Tertiary Lake Beds............. 899 Distribution of the Coal Fields.......... 899 Classification of Montana Coals.........900 General Statement............. 900 Comparison of Chemical Analyses and Heating Values..901 DESCriPTions of the CoaL Fields.......... 905 • Fields Containing Bituminous and Higher Grade Coals..905 Bridger Field............. 905 Stillwater Field............ 906 Electric Field............ 907 Trail Creek Field...........908 Gallatin Field............909 Lombard Field...........910 Great Falls Field............ 910 Lewistown Field............ 911 Valier Field............. 912 Blackfoot Field............ 913 Fields Containing Sub-bituminous Coal.. 913 Bull Mountain Field..........913 Red Lodge Field............ 914 Missoula and Drummond Fields......... 916 Milk River Field............ 916 The Eastern Plains Region of Lignite and Sub-bituminous Coal.... 917

Jan 1, 1914

By Gustaf Ising

For relative gravity measurements, the author in 1918 described an instrument1 of which the essential part consists of a highly astatized, standing pendulum turning about a horizontal elastic axis. This type of instrument has been used recently in practical field work, therefore a description of its principle and technical development is given herein. Part I, describing the principle, is a direct translation of the original Swedish paper.1 Part II gives an account of the practical elaboration of the instrument, together with some description of measure-ments performed.

Jan 1, 1937

Jan 1, 1951