Search Documents

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, 'however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel ' 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650' C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

Discussion of the paper of E.. C. LEE, presented at the St. Louis meeting, October, 1917, and printed in Bulletin-No. 130, October, 1917, pp. 1825 to 1832. H. M. WILSON, Pittsburgh, Pa.-The statement ill the paper of T. T. Read, "Increasing Dividends Through Personnel Work;" that the offering of substantial money rewards for avoidance of accidents is much more effective than mere propaganda or education respecting accident prevention, is a, point fully substantiated in the experience of insurance inspection under workmen's compensation acts. The first year under the Workmen's Compensation Law in Pennsylvania, during which over 2000 mines were tinder the observation and protection of the inspectors of the insurance companies, has resulted in several inspections of each mine, a splendid cooperation .between the operators, the State mine inspectors and the insurance inspectors, and an average reduction in premium rate for insurance from $3.83 to $2.77, a reduction of more than $1 per $100 of payroll, on an average payroll of nearly $100,000,000, In other words, the insurance companies have

Jan 1, 1918

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By S. Kobayashi, A. E. Armenákas, C. Mylonas

Earlier work1-4 has shown that commercial mild steels under static loading at the lowest natural operating temperatures fracture in a brittle manner only when damaged by a suitable history of straining. Notched and then compressed plates have fractured in subsequent tension at loads as low as 10 pct of the limit load and precompressed smooth bars at a subsequent extensional strain as low as 0.01. The comparison of the average net fracture stress with the flow limit stress was shown to be an excellent criterion of brittle or ductile behavior of mild steel structures when only loads and general stress levels are known. The present investigation shows that the deformation at fracture is a far more sensitive measure of brittleness than the fracture stress. Both criteria, deformation and stress, are used to determine the amount of uniform precompression of two mild steels, ABS-B and Project E-steel, resulting in brittle fracture under the strong constraint of a subsequently machined severe circumferential groove. The fracture stress equaled or exceeded the theoretical flow limit Ól = 2.680., ('based on the elevated yield stress at each prestrain) up to prestrains of about 0.20 and then fell off to about 1 at prestrains of 0.60. Yet a prestrain of only 0.05 reduced the elongation at the shoulders by a factor of about 4. The total plastic elongation of a region surrounding a sharp notch in prestrained steel deternines whether or not fracture will be initiated in large structures, hence is a direct and realistic measure of the remaining ductility and provides an excellent test of the material's resistance to embrittlement. ALMOST all engineering structures of mild steel which failed in service in a so-called "brittle" manner exhibited appreciable local plastic deformation (more than 1 pct) and a mixture of "cleavage" and "shear" fracture surfaces. Furthermore, the peak local stress in an advancing crack is always high. Such simple criteria as pure cleavage, absence of plasticity, or fracture stress, so useful in other fields, are insufficient to characterize brittleness in engineering structures at ordnary temperatures. The "brittle)' behavior of engineering structures is caused by the limited ductility at cracks or notch regions, as shown by recent work at Brown University summarized and extended in Refs. 1 to 4. It was also shown that the local ductility of mild steel may be catastrophically reduced by a suitable strain and temperature history similar to those which may occur in real structures. Localized yielding begins at the notch roots at low loads but is contained by surrounding elastic regions. The plastic strains are hence small. They increase slowly with the load up to the flow limit or limit load for an ideally plastic material. Unrestricted plastic flow then occurs. At such strains the real material locally st rain-hardens and fractures. With work-hardening materials no flow limit exists, and the transition from low to high plastic strains is gradual but increases more rapidly at loads close to the flow limit of an equivalent perfectly plastic material. When the available ductility is sufficient for reaching the limit load, the behavior is normal or "ductile". With insufficient ductility, fracture will occur at a low load and will be defined as "brittle". Accordingly the sufficiency or not of the ductility at a notch is reflected in the magnitude of the fracture load or average net stress as compared with the limit load or flow limit. The application of this criterion gave surprising results. Service failures under semistatic loading occurred mostly below the limit load, hence were "brittle". On the contrary all static tests with undamaged commercial mild steels reached the limit load in spite of the deepest notches and temperatures below Charpy impact transition (say about -30°F or higher). Notched bars showed no brittleness even under fully dynamic axial loading up to 1.5 x107 psi per sec at -23°F and about 2.5 x l06 psi per sec at -ll0°F, but broke in a brittle manner at -200°F and l03 psi per sec.' To propagate a fracture at low load, experimenters had to trigger it by superimposing a strong dynamic impact at a notch cooled by liquid nitrogen as in the Robertson5 or Esso tests.' Once started the cracks would run through warmer regions of smaller stress. Obviously the ductility of the apparently undamaged commercial steels was "sufficient" in the laboratory tests but not in the service fracture, where it must have been reduced by some embrittling procedure of fabrication or service. These conclusions were confirmed by the achievement of low static stress (brittle) fracture initiation in unwelded steel after a local reduction of ductility by simple prestraining. Symmetrically notched plates of undamaged mild steel cooled below the Charpy V-notch transition range were tested in central static tension: Undamaged plates withstood loads of limit intensity, but when subjected to prior in-plane com-pressive prestraining perpendicular to the notch axis and to accelerated aging, the plates fractured completely or partially at very low static loads, as low as one-tenth of the flow limit.2-4 However, damage could not be easily related to the strongly variable prestrain around a sharp notch. To obtain easier strain measurements, it was decided to use axially precom-pressed bars and bent bars. Final testing was done by

Jan 1, 1970

By G. Carman Ridland

A program of exploration for radioactive deposits, conducted in 1945 in the well-known mineralized areas of the Front Range, Colorado, was rewarded with the discovery of pitchblende in a dump at Caribou Hill. The presence of pitchblende in. the silver veins at depth apparently is not expressed as gamma-ray anomalies at the surface.

Jan 1, 1950

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By H. W. McCue

In 1945 the number of oil wells drilled was less than in 1944 but the number of gas wells was greater. The oil wells numbered 176, completed for an initial production of 25,214 bbl., an average of 143 bbl. per well as against a total in 1944 of 245 drilled for 32,886 bbl., or 134 bbl. per well. All of these wells were in proven areas and no new discoveries

Jan 1, 1946

H. W. MussEn, Collingwood, Ontario, Can. (communication to the Secretary*):—Doubtless all engineers who have paid more than a casual visit to Russia have come into contact with that formidable document, the " smieta," or estimate of the Russian manager. It is an institution which seems to be inseparable from Russian mining-methods. As Mr. Shockley points out, the year's costs a agree very closely" with the figures of the smieta made at the beginning of the year. In cases which have come under my notice, I have been satisfied that there had been a good deal of " rigging" of accounts to this end. The sum spent by the manager was carefully kept down to the total of the estimate, because it was well known that no more money would be forthcoming, and when this is done it is not a difficult matter to see that the right amounts come under the right heads in the final accounts. I do not say that this is always the case, but I have come across notable instances. Looking at it from the Russian owner's point of view, I think that the balance of the argument is usually in favor of the smieta as limiting " impulsive indiscretion" on the part of managers. The Russian Mining Code of to-day leaves much to be desired, but this is thoroughly appreciated by the official world there, and great changes are spoken of for the future. In many, if not in most, cases the laws are interpreted liberally, and a great deal is left to the discretion of the district mining engineer or inspector, with whom it is necessary to keep in close touch. As Mr. Shockley points out, the officials of a mine, who are always Russians, are held personally responsible for accidents resulting to employees, quite independently of any compensation which may be made to the sufferer. This seems startling enough, but I have always found that a penalty is imposed only

Jan 1, 1909

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By W. M. Peirce

FOR many years it was considered quite the proper introduction to any discussion of zinc metallurgy to remark that the methods of extracting zinc from its ores were archaic. Often there was an added implication that the industry in every phase savored of the days of alchemy. On rare occasions comments of this sort may still he heard. Fortunately, not only for the zinc industry but for the world at large, there is today no longer a basis for considering zinc metallurgy unprogressive. Progress in any industry is possible along three distinct lines. The methods of production may be improved, thereby reducing costs. In the case of basic materials, this may also have the important effect of increasing potential supply. Second, quality may be improved. Finally, the product may be made more valuable to consumers through increased knowledge of its utilization, thus holding old markets or opening new.

Jan 1, 1931

By J. V. W. REYNDERS

THE principal manganese deposit of Russia, I one of the four principal sources of the world's supply, lies on the southern slope of the Caucasus Mountains, in what is now the Republic of Georgia, district of Sharopan. Tchiatouri, the principal town, is midway between Tiflis, the capital of Georgia, and Poti, the shipping port on the Black Sea, about 130 " miles distant. The deposit can be most easily visualized by thinking of a nearly horizontal coal seam about 6 ft. thick, outcropping on the slopes about 600 ft. above the Kvirila River. One of the accompanying illustrations shows the river, which nearly bi- sects the district, of approximately 50 sq. miles in area, and with its tributary streams makes the topography rugged, while in the background are the snow-capped peaks of the Caucasus range. Another of the illustrations gives a closer view of the outcrop. The roof and floor of the deposit are good, so the methods of working are quite similar to working a coal seam, especially as most of the mineral is soft enough to be mined with a pick. Little machinery is used, except small cars for underground transportation.

Jan 1, 1926

By AIME AIME

THE annual session for the election of officers and transaction of other official business of the Institute, which must be held, in accordance with the By-Laws, in New York on the third Tuesday in February, was the only session scheduled for the morning of Feb. 19. Many members gathered in the auditorium at 10 o'clock, and President George Otis Smith presided. He said that his report was best set forth in the reports of the other officers and committees, which were avail-able in printed form. Productive activity had characterized the Institute's year and a number of new ventures had been successful. He felt that he had "rattled around" in the office of president, as he had traveled some 39,000 miles during the year in visiting the various Sections, having visited everyone that had held a meeting during his term of office. He spoke of the educational effect on a president of these broad contacts and suggested that a three-year course would be even more enlightening than one.

Jan 1, 1929

By W. M. Raynor

LARGE quantities of "midnight oil" have been consumed by researchers in attempting to develop a process to produce cold ductile zirconium at low cost. The tantalizing facts that zirconium is a bright, silvery, tarnish-proof metal and is 2 1/2 times as abundant in the earth's crust as copper, and thirteen times as plentiful as lead have resulted in much speculation on uses, ranging from automobile radiator grills to kitchen sinks. but unfortunately no low-cost process of producing it has so far been found. In the case of zirconium, we cannot say that "virtue is its own reward" for the principal virtues of the metal, namely, corrosion resistance at ordinary temperatures and ability to absorb gases at high temperature, are the very characteristics that defeat all of the usual recovery methods such as sintering, plating, or direct chemical reduction. The only method giving a pure metal sufficiently low in oxides, nitrides, etc. to be truly cold-malleable is the one developed by Van Arkel and DeBoer in 1925. This process involves decomposition of zirconium tetraiodide in contact with a hot filament and pre

Jan 1, 1947

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By AIME AIME

THE non-ferrous alloys have been placed in the same class with steel by metallurgical research on hardening, and hardenable alloys of all metals except zinc are now manufactured. The hardening of the non-ferrous alloys is accomplished by a process of heating, quenching and ageing. R. S. Dean, head of the research department of the Western Electric Co., told of the results of this research in 'a lecture on "Recent Advances in the Art and Science of Fabricating Metals," given before the Missouri Mining and Metallurgical Association on Jan. 24, 1929.

Jan 1, 1929

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

BENEFICIATION AND CONCEN'TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979