Search Documents

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930

By Courtenay de Kalb

REVISION of the United States mining law is needed. chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. LAW OF THE APEX The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from masses which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future. development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes

Jan 2, 1915

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, yet in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has been mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been al most entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is amazing that the iron companies will persist in sending abroad under. heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below-will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests were conducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color .to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition Water, - 2.68 Silica, - 65.46 Iron oxide, - 2.10 Alumina, - 15.02 Magnesia, - 15.35 100.61

Jan 1, 1882

By C. J. Hicks

The labor policy of the Standard Oil Co. (New Jersey) is founded first of all on paying at least the prevailing scale of wages for similar work in the community; on the eight-hour day at the refinery, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; opportunity for training and advancement; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; coöperation with employees in promoting thrift and better social and housing. conditions; and assurance of a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co. (N. J.), is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, and not at variance with the interests of the stockholders, and that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer. Though the plan has been in operation nearly two years, it is an experiment, in that, being based on a principle rather than on cut-and-

Jan 1, 1921

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By H. D. Strain

Potash is a generic term used to describe a number of compounds containing the element potassium (K), which is one of the three major plant nutrients. Potash content of these compounds is commonly expressed as percentage potassium oxide (K20), and the market value of the products is usually dependent on contained K20. Most of the potash produced (approximately 95%) is used in agriculture as fertilizer. Potash products today are shipped by producing countries all over the world to meet the need for increased food production. WORLD POTASH RESERVES Apparent world potash reserves are shown in Table 15.2B.1 and total some 96 billion mt of recoverable potassium oxide. The Canadian reserves account for approximately one-half the known world reserves. The reserves shown represent the potassium oxide content of a variety of potash-bearing ores. The major ore is sylvinite (a mechanical mixture of KC1 and NaCl) from which KC1 or sylvite is recovered (63.2% K20 equivalent). Other ores, such as langbeinite (potassium, magnesium sulfate-22.7% K20) and carnallite (potassuim magnesuim chloride-17.0% K20) are also mined in various parts of the world, mainly for the potassium content. Theoretically, potassium is available in almost unlimited qualities from brines and saline waters. To date, the cost of recovery from salt brines has been greater than the costs by mining operations, but new technology could make brines and seawater an increasingly important source. POTASH PRODUCTION Potash production dates back to the 1860s in Germany, which was the only recorded producing country until 1912. By 1912 Germany was producing approximately 1 million tpy of K2O equivalent. Production began in France in 1913 and in the United States in 1915. World potash production and consumption are shown in Table 15.2B.2 for the years 1950-51 through 1967-68. In 1967 and 1968 the major potash-pro¬ducing countries in order of importance were those listed in Table 15.2B.3. By 1972 Canadian production had outstripped U.S. production. WORLD CONSUMPTION World consumption of potash for the years 1950-51 through 1967-68 is shown in Table 15.2B.2. Table 15.2B.4 shows total world consumption of potassium materials in 1967-68 by country. More than 70% of the world's potash is

Jan 1, 1976

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934

By L. H. Schwartz, M. V. Nevitt

THE phase Ti2Ni has been described by Laves and Wallbaum,1 who found the phase to be face-centered cubic with 96 atoms per cell, by Duwez and Taylor,2 who confirmed these observations and reported a lattice parameter of 11.333A, and by Rostoker,' who reported the structure to be isomorphous with the double carbide Fe,W,C, type E93, and to have a lattice parameter of 11.29A. In this study a group of isostructural phases has been found among alloys of certain second and third long-period transition elements. The systems investigated included all the combinations of zirconium and hafnium with the Group VIII elements rhodium, palladium, iridium, and platinum. There is evidence that many of these new Ti2Ni-type phases require oxygen for their stability in the temperature ranges in which they were studied. EXPERIMENTAL PROCEDURE Alloy samples weighing 5 g were prepared by arc-melting metals whose purity is indicated in Table I in a helium-argon atmosphere. Samples of the as-cast buttons, wrapped in molybdenum foil and sealed in evacuated quartz tubes, were

Jan 1, 1959

By Eugene McAuliffe

The mining press, as well as certain federal and state bulletins, refer from time to time to the relative hazards that attach to loading bituminous coal by hand when compared with the so-called "mechanical loading" process. Much of the coal coming under the head of hand-loaded coal is won in part by the use of machinery; the coal-cutting machine is in general use, the electric power drill employed to a lesser extent. Therefore it may be said that the principal difference in the process employed, mechanical loading versus hand loading, lies in the fact that some type of loading machine is employed in the mechanical loading process to lift the coal from the face of the room, place or entry, after it is mined, placing it in the pit cars for transport to the tipple. It is a common practice to compute accident records on the basis of tons mined per fatal and per nonfatal accident, disregarding the fact that it is possible to produce by the aid of coal-loading machines the same daily, monthly and annual tonnage with a much smaller force than is required where the coal is all shoveled by hand. Inasmuch as the men who are released by the substitution of machinery for hand labor must find employment elsewhere, suffering some measure of hazard in their new occupation, we are of the opinion that the true relative hazard that attaches to the processes of mechanical loading and hand loading can be determined only by using as the basis of comparison "man shifts worked" or "hours of exposure" experienced per accident. The Union Pacific Coal-Co., beginning with the year 1929, undertook to maintain a true record of man shifts worked per compensable accident, giving equal weight to fatal and nonfatal accidents. Accidents lacking sufficient severity to come under the compensable terms of the Workmen's Compensation Act were not included in the compilation, the Act providing that "no compensation, except the expense of medical attention, shall be allowed for the first seven (7) days of disability, unless the incapacity runs beyond the period of twenty-one (21) days, in which case the compensation shall run from the time of the injury." With the further thought that all accidents suffered by employees engaged in any service, in or about the place where the loading process

Jan 1, 1931

By J. B. Neale

FRom the beginning of its activities, the members of the National Production Committee have felt that the following points were essential to the success of its work: The operators must feel that their operations were not 100 per cent. efficient; that they should be courteous and fair in their treatment of their employees; and that they should set an example of hard work and patriotic interest in increased production. Every move made must appeal to the sense of fairness of all parties concerned. The men must feel that in working more faithfully, and consequently producing more coal, they are rendering a distinct service to their Government in the time of its great need. As the workers feel that greater efficiency on their part results only in greater profits to the operators, the advantage to the operator should be lost sight of, as far as possible, and the advantage to the Government in fighting the war emphasized. Both operators and workers should know that the Government considered increased production an obligation, and opportunity for service, resting on both parties and not on the operators or the workers alone, and that both parties could very much better the efficiency of the pre-war period. Had the committee intimated that it thought the coal shortage was due entirely to the idleness and inefficiency of the workers, its campaign would have failed, for the men would have resented the charge because only too frequently their efforts to produce more coal were thwarted by bad management; besides, the operators would have lacked stimulus to better effort. On the other hand, had the impression been given that the committee thought that the coal shortage was due entirely to bad management, the operators would have resented the charge because only too frequently their efforts to produce more coal were thwarted by the idleness and inefficiency of the workers; and the workers, having been thus indirectly pronounced 100 per cent. efficient and patriotic, would have lacked stimulus to better effort.

Jan 1, 1920

By A. P. Anderson, J. H. Jensen, W. E. Breckoff

Bromine is the intermediate member of the halogen family of elements between iodine, a solid, and chlorine, a gas. The name is derived from the Greek "bromos," meaning stench. Bromine is the only nonmetallic element that is liquid at room temperatures with a melting point of -7.2° C and a boiling point of 58.78º C. Reddish brown in color, it dissolves easily in water to yield a red solution. Bromine volatilizes at ordinary temperatures to a red vapor that is very irritating to the eyes, nose, and throat. Density of the liquid is 3.12 and gas weighs 7.59 gpl at standard conditions. As the element is highly active, it exists in nature only as bromide compounds. Bromine was discovered by Antoine Jerome Balard in seawater bitterns in 1826 and first prepared in quantity in 1860. Distribution Bromine is widely distributed in nature and compounds occur in solution in natural brines, in seawater, saline lakes, oil and gas well brines, and in evaporite chloride minerals. The concentration of bromine salts ranges from 60-65 ppm in seawater to several thousand ppm in oil well brines and saline lakes. The distribution of bromine in marine evaporite minerals and in the solutions from which they crystallized was determined many years ago by H. E. Boeke (1908). Theoretical aspects regarding the geochemistry of bromine have been published in numerous papers (Raup and Mite, 1969). Bromine occurs in solid solution in carnallite and sylvite associated in potash deposits; in halite in salt beds; salt in oil shales; and in trona deposits. Its presence is useful as a guide in geochemical exploration. The analysis of small amounts of bromides in the presence of large amounts of chlorides is discussed by W. Schwerdtner (1963). Manganese, iron, and iodine may interfere with the determination. Other analytical methods are discussed at length in the literature (Stenger and Atchison, 1964). Sources and Reserves The sources and reserves of bromine, given in Table 1, appear ample to meet present and foreseeable requirements in all producing countries. With the occurrence of bromine salts in seawater and other brines, the potential for bromine production is worldwide. It has been estimated that 99% of all commercially recoverable bromine is in the ocean. However, actual subterranean brines having a higher bromine content than seawater will continue to be the preferred sources of bromine for the foreseeable future. [ ]

Jan 1, 1983

By Vincent P. Gianella

THE most intense earthquake on the Pacific coast in the last several years, and probably the second most intense shock to occur in Nevada since it was settled, was felt in many Western States shortly after 10 p.m. on Dec. 20, 1932. Be- cause the rifted area contered about the northern end of Cedar Mountain it is referred to as the Cedar Mountain, Nevada, earthquake. An idea of the intensity of the shock may be gathered from the distance at which it was felt: in Wyoming, Utah, Idaho, Nevada, Washing- ton, Oregon, California and Arizona. It is the strongest quake centering in Nevada since the Pleasant Valley earthquake on Oct. 2, 1915. Despite the strength of the vibrations and the large area over which they were felt, relatively little damage was done. The extent of the damage consisted of a few old stone buildings demolished as shown in Fig. 1, much cracked and fallen plaster, many chimneys shaken down and considerable cracking of brick walls. There were no deaths and four people were but slightly injured. The small amount of damage was due, largely, to the scarcity of structures within the area of strong vibrations, but an important factor was the aridity of the region (see Fig. 2) and the shallowness of soil cover so that there was but little water-saturated loose material in which strong secondary vibrations could be formed. Had this earthquake occurred in a region of heavy precipitation and dense population the damage to property and loss of life would undoubtedly have been large, with consequently much more newspaper publicity.

Jan 1, 1933

By Thomas Fraser, Alvaro Abreu

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By Milnor Roberts

CORNWALL, a Mecca for metal miners the world over, is easily reached from the southern coast of England. Passengers who land at Plymouth or Southampton can connect with a fast train from London called the "Riviera express," which traverses the beautiful counties bordering the English Channel. In Cornwall the traveler soon notices the pits and stock-piles of white china clay, and the metal mines, both placer and hard rock. The deposits are associated with granite batholiths, of which there are four principal ones, each a few miles in diameter. Tin mines are especially worked in the granite near its borders and also in the immediately surrounding Paleozoic slates. Copper and lead are no longer of importance here but tin is being produced steadily from several mines, with arsenic and tungsten as by-products. At the close of the war the man-power available. for these mines had been reduced to one-third of normal, and only now is it again reaching full strength. As mining in Cornwall antedates the Christian era, even a Nevada prospector would have to admit that "she's a permanent camp." SUB-TROPICAL CORNWALL Redruth and Camborne are industrial centers of the tin mining industry, but more tourist hotels are found in neighboring resorts such as St. Ives, a quaint fish-ing town on the Atlantic-side of the peninsula of Corn-wall, where the numerous cats descended from those mentioned in the ancient riddle-rhyme about St. Ives now occupy every doorstep and wall. Another charm-ing resort. Penzance on the shore of the English Channel, is known by name to the public through the opera "The Pirates of Penzance," but is of especial in-terest to students of nature for its palm trees and other subtropical plants, which thrive owing to the nearness of the gulf stream, although the latitude is that of northern Newfoundland, Winnipeg, and the northern end of Vancouver Island. Among the industrial plants at Camborne are those of Holman Brothers, Ltd., where drills and other forms of mining equipment are manufactured. At the Corn-wall School of Mines, which specializes on the district, the staff has assembled excellent collections of local ores, which repay study by a visitor.

Jan 1, 1928

By Alvaro Abreu, Thomas Fraser

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By W. C. Lilliendahl, H. W. Highriter

THE method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF6) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then pressed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times the uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphite crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO2 in Ascarite, using air instead of oxygen to reduce the temperature and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1).

Jan 1, 1935

Discussion of the paper of S. E. Bretherton, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1481 to 1487. S. E., BRETHERTON, San Francisco, Cal.:-Since preparing my paper, our chemist, F. L. Wilson, has been experimenting with Leadville, Colo., oxidized zinc ore and Leadville zinc sulphides containing lead, operating upon 40-1b. lots at a time. His results on Leadville sulphides are as follows: The raw ore contained a trace of gold, 5.04 oz. of silver, 19.1 per cent of zinc, and 7.24 per cent of lead. After roasting the ore contained a trace of gold, 5.72 oz. of silver, 0.75 per cent of copper, 21.7 per cent of zinc, and 8.29 per cent of lead. The loss in weight by leaching was 38.8 per cent. The extraction was 42.8 per cent of the copper, 80.6 per cent of the zinc, 7.1 per cent of the lead, 0.64 per cent of the silver, and no gold. The little .silver that is extracted would be thrown down with the copper when precipitating it from the zinc and both thrown hack into the residue to be smelted. There would be no trouble in smelting the residue with nearly all the sulphur eliminated and containing less than 7 per cent. of zinc. On zinc carbonates containing silicates the results are not satisfactory. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :¬The paper by Mr. Bretherton upon the application of ammonia and carbonic acid to the recovery of zinc as oxide from roasted sulphide ore is of interest to me, as the first installation of the Schnabel process for the extraction of zinc from a mixture of zinc oxide, lead oxide (with some cupric oxide), and pellets of enriched lead, produced in steaming liquated zinc-silver-lead crust of the Parkes process, was made at Lautenthal, Harz mountains, where I was chemist. In that capacity I carried out numerous experiments on the Schnabel process, was active in the erecting of the plant, and later had charge of it. After the Lautenthal plant had been in operation for some time a similar one was built at Hoboken-les-Anvers, but both have been abandoned, as the wet process could not compete with the distillation of the liquated zinc-silver-lead crust, now used universally in the Parkes process.

Jan 11, 1913

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956

Further discussion of the paper of JAMES JOHNSTON, presented at the New York meeting, February,. 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. See also Bulletin No. 91, July, 1914, pp. 1473 to 1496. THOMAS CROWE,* Victor, Colo.-The interest manifested of late in the treatment of low-grade ores, together with Mr. Clevenger&apos;s discussion of the Mill and Metallurgical Practice of the Nipissing Mining Co., prompts me to acid a few remarks relative to concentration in connection with cyanide treatment of low-grade ores. Mr. Clevenger in this discussion does not condemn concentration in this connection, but, nevertheless, the tone of his remarks would lead one to believe that his conclusions are like those of many others: that concentration is often turned to as a last resort in an attempt to improve or obtain an extraction upon an ore by the recovery and sale of the refractory portion of the ore. This, I will attempt to point out, is not always the case. Concentration in connection with cyanidation often performs an entirely different function, i.e., one of saving fine grinding. Economy being the keynote of successful treatment of low-grade ores, the problem often becomes more commercial than metallurgical, and, as there is generally a definite ratio existing between cost of operation, degree of comminution, and percentage of extraction, the grade of ore under treatment usually imposes a limit upon these factors. With many ores grinding is the most expensive single item in their treatment; therefore, the degree of comminution is very apt to be governed by the allowable cost of operation. With most ores the degree of comminution controls to a great extent the percentage of extraction. So in the treatment of low-grade ore it often becomes necessary to sacrifice extraction, through coarse grinding for the benefit of cost, in order that the greatest ultimate profit may be obtained, and it is under these conditions that it is, possible for concentration to play an important part in overcoming to some extent the effect of mesh. The precious metals occurring in an ore are usually closely associated with the metallic portion of the ore, and as this metallic portion is generally fairly well liberated from the gangue at comparatively coarse meshes, further grinding of the ore is necessary only in order that the metallic portion may be reduced sufficiently fine that the precious metal part of it may be dissolved by cyanide solutions in a reasonable length of time.

Jan 11, 1914

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972