Search Documents

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By W. P. Z. German

Some attention should be given to definitions. The term "unit operation " may have at least two meanings. One meaning is the merging of titles and the development and operation of the unitized area, as if it were one tract of land held under a single oil and gas lease, according to a definite program intended to accomplish a maximum recovery from the pool as a whole at a minimum of cost. It is incomplete when the royalty owners do not also merge their titles to their oil and gas rights in the area, and is complete when they do. The other meaning is not accompanied by any merger of titles, but the development and operation of the area is in accordance, as nearly as reasonably practicable, with such a program. This second conception may be nothing more than a cooperative development and operation plan, but in this paper it is regarded as more than that. If there cannot be unit operation without a merger of titles, it would seem that the state cannot require unit operation, for it cannot require a merging of titles; but if it may consist in requiring each and all of the leaseholders to develop and operate or to submit to a development and operation according to some such common plan as is referred to above without at the same time requiring a merger of titles, it would seem that unit operation may be required by the state. Whether the states have this power is the subject to be herein considered. If the state can so bind the several lessees, it also can so bind the several lessors. The writer does not know what would be an ideal plan for the development and operation of a pool; but it takes into account the fact that the accumulation of gas and oil is not uniform throughout the formation; that often free gas, highly compressed, occupies the upper portions of the reservoir, the oil with compressed gas in solution coming next in order; that at places oil is not overlain by free gas, and sometimes there are peaks where free gas is not immediately underlain by any oil; and the fact that these substances are held under a uniformly distributed pressure, generally referred to as "rock pressure." It also recognizes that the most efficient utilization of this naturally existing reservoir pressure in the recovery of the oil requires that there be no operation of wells completed into areas where gas only has accumulated, for this diminishes the

Jan 1, 1931

By A. K. Snelgrove

This symposium is designed to marshal a state-of-the-art account of approaches and solutions to problems arising out of waterlogging and salinization in the world's largest irrigation system which was dismembered by legal beheading of the Eastern Rivers under the lndus Waters Treaty of 1960. In this introduction, the geological and historical backgrounds of surface waters and groundwaters in the Indus Basin are presented with a summary of remedial measures undertaken and proposed to combat waterlogging and salinization. At a time when water-resource planning is proceeding on a continental scale, a study devoted solely to the Indus River Basin may seem to require an apologia. None is offered, however, for three major reasons: (1) Although the Indus is a single river basin, it is one of great magnitude and importance. The Indus River, which comes from Himalayan sources to form part of the great Indo-Gangetic Plain drainage system, is vital to agriculture and hydroelectric power in the thickly populated northern subcontinent of Indo-Pakistan. (2) The Indus has become a plexus of extraordinary problems since the dismemberment of the world's largest irrigation system of which it was a part. The break-up of this system occurred with the legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960. (3) Th River Basin has been the target of a Herculean effort to contain the twin encroachments of waterlogging and salinization that now threaten it with a shortage of fresh water. The British irrigation system of barrages and canal on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage. To cope with this situation, there has been a possibly unprecedented concentration of domestic and international engineering and scientific talent on the Indus and its problems (about a score of organizations by recent count). To marshal a state-of-the-art account of their approaches and solutions is the purpose of this Symposium. The coordinated effort now being made on a variety of fronts under the general supervision of West Pakistan Water and Power Authority (WAPDA) is directed toward the modification and control of interactions and relationships between geological materials — soils, water and its salt balance, and air —in what has been termed a huge "underground lake" in an alluvial basin. The problem is an intriguing one in that a highly complicated case history of river-course changes visible in the present surface must be projected downwards through Recent and Pleistocene sediments in order to decipher the environmental controls of deposition in terms of vertical and lateral variations in lithology and patterns. Such studies must be extended to compaction, deformation, and fabrics of the alluvium. Geohydrology is often defined as groundwater hydrology. As employed herein, it includes the distribution, quality, and behavior of surface and subsurface waters, including their evolution, vagaries, and geological, climatological, and botanical milieux." GEOGRAPHY The Indus (Sanskrit, Sindhu = river) rises at nearly 17,000 ft above the sea in the glaciers on the northern slopes of Kailas Parbat, Tibet. It is about 1800 miles long and has a total drainage area estimated at 372,000 sq miles. The average discharge is 196,000 cfs at mouth. Leaving the Plateau of Tibet, the river flows at a level which is miles above the sea, and in places miles below Himalayan peaks, in a structurally controlled northwestward course. Joined in this course by six tributaries and swollen by the melt waters of giant glaciers, it swirls about the base of the famous

Jan 1, 1970

By A. C. Heath, E. H. Dix

THE importance of aluminum-silicon alloys in the light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and like silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminum and aluminum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. PART I.-ALUMINUM-SILICON ALLOYS The early work on this system was largely confined to determining the general form of the diagram and in this respect the results are in good agreement. Briefly, aluminum and silicon form a simple eutectiferous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Fraenkel1 (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solution. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility does not appear

Jan 1, 1928

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By A. S. Odeh

The mechanism of two-phase flow in porous media has been a subject of wide controversy. One of the properties essential for understanding the dynamic behavior of two-phase flow is relalive permeability. Relative permeability to a certain phase is defined as the ratio of the effective permeability of that phase to its permeability when it is the only fluid present and powing. In this research, a theoretical analysis was made to determine the effect of viscosity ratio between the non-wetting and the wetting phase on relative permeability. Experimental work was conducted to test the validity of the derived equations. The experiment was conducted on four natural cores. Four oils were used as the non-wetting phases with a viscosity range of 0.42 to 71.30 cp and two wetting phases with a viscosity range of 0.86 to 0.96 cp. Oil and bring were made to flow simultaneously at various ratios, and relative permeability curves were constructed. A total of eight relative pertileability cycles representing eight viscosity ratios were run oil each sample. It was found that relative permeability to the non-~cletting phase varies with viscosity ratio. The relative effect of this variation on relative permeability values was a function of the sample's single-phase permeability, decreasing with its increase. It was concluded that, for .samples of single-phase permeability over I darcy. the effect of viscosity ratio could be disregarded, and relative permeability would be, in effect, a function of satrtration only. INTRODUCTION Two-phase as well as multiphase flow occurs in many fields of science. This type of flow is of particular interest in petroleum production. The knowledge of relative permeability, which describes the dynamic behavior of two-phasc as well as multiphase flow, is essential for solution of problems arising in that field. Thc relative permeability ot a porous medium to a given phase in multiphase flow. is generally considered to be only a function of the saturation of that phase, independent of the properties of fluids involved and ranging in value from zero to unity. Work by Leverett' and Leverett and Lewis' apparently supports this concept. In his experiments Leverett used a clean, packed unconsolidated sand of high permeability (3.2 to 6.2 darcies) with two phases (water and oil) flowing and a viscosity ratio range of 0.057 to 90.0. His results showed that the wide range of viscosity had practically no effect on relative permeability-saturation relationship. Recently accumulated evidence from work performed by several laboratories and a paper by Nowak and Krueger,2 in which relative permeability to oil of a few core samples in the presence of interstitial water was considerably greater than single-phase permeability to water, cast some doubt on the conclusions reached by Leverett' and subscribed to by a large number of individuals in the oil industry. One explanation advanced to explain this behavior states that it is caused by the variable extent of hydra-tion of clay minerals present in the sand. The greater the water saturation, the greater will be the area of contact between water and clay minerals; therefore, the greater will be the extent of swelling with corresponding reduction in permeability. Yuster4 presents another explanation for the recently accumulated evidence. Utilizing Poiseuille's law, he analyzed concentric flow in a single capillary where the non-wetting phase flows in a cylindrical portion of the capillary and concentric with it. The wetting phase flows in the annulus between the non-wetting phase and the capillary wall. The equations obtained indicate that relative permeability to the non-wetting phase is a function of saturation and viscosity ratio. Although Yuster's equations show that fractional rel-ative permeability to oil could be greater than unity, as was indicated by the data of Nowak and Krueger,1 they failed to present an explanation to the experimental data of early investigators such as Leverett.1 Due to the importance of relative permeability in understanding the flow behavior of petroleum reservoir fluids, this work—theoretical as well as experimental —was undertaken to determine whether relative permeability is a function of saturation only as was concluded by Leverett1 or a function of saturation and viscosity ratio as was theorized by Yuster.4 THEORETICAL ANALYSIS An equation will be derived for the rate of oil flow through a porous medium that is initially filled with water. Based on this equation, an analytic expression for relative permeability will be developed. The porous medium will be assumed to consist of .straight circular capillaries of different radii. It will also be assumed that there are no interconnections among the capillaries and no mass transfer across the oil-water interface. Consider a porous sample initially saturated with a wetting phase (water). As a non-wetting phase (oil) is

By W. F. Chiao

With the application of dislocation damping theory an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. A ductile steel was compared with a brittle stee1 by simultaneously measuring the ultrasonic attenuation and velocity during tensile test, and the density of free dislocations and their mean loop length were then calculated as a function of strain. The results showed that in the ductile steel there was always a large generation of dislocations and great extension of loop length occurring at some stage within the early plastic region. In contrast, the brittle steel showed very little or no such sudden changes in dislocation dynamic states after the onset of plastic deformation. Furthermore, a strong temperature dependence of dislocation dynamic states was also observed in the ductile steel and a hypothesis was suggested that a thermally activated process of dislocation rearrangement could occur at higher deformation temperatures. The activation energy of dislocation rearrangement at room temperature was estimated as about 2030 cal per mole.C. DUCTILITY is an indispensible property in the application of engineering materials, especially steel. During the past two decades the theoretical and experimental approach to the understanding of flow and fracture of metals has been constantly undergoing changes and progress." while the fracture behavior of metals can be influenced by many factors such as chemical Composition,3 second-phase particle mor-phology,4 and dislocation arrangement,5 it is now a general belief that the fundamental understanding of the ductile-brittle fracture phenomena of solid materials must stem from the study of dislocation dv-namics developed under stress conditions.6,7 Most of the traditional ductility tests, such as Charpy impact test, slow bend test, and tensile fracture test, cannot by themselves reveal directly the mechanisms of ductile to brittle transition of materials. In the experimental investigation of tensile ductility it would be ideal to be able to study directly the dynamics of dis-locations in a bulk specimen during the process of deformation. Since the ultrasonic pulse technique is the only satisfactory method for studying dislocations and the fine details of deformation characteristics in metals in the course of a tensile test, it would appear that a comparative study of ultrasonic attenuation changes during tensile tests of metallic materials exhibiting different ductility might be very informative. So far no work comparable to this study has appeared in the literature. Recent progress in both theory and experiment has indicated the feasibility of studying the dislocation mechanisms of ductility behaviors by ultrasonic measurements during tensile test. Granato and Lucke8 have developed a quantitative theory that enables the calculation of dislocation density and their average loop length from the measurements of ultrasonic attenuation and velocity, and several investigators, including Chiao and Gordon,9'10 have shown that simultaneous ultrasonic measurements can be successfully made during a tensile test. Furthermore, many investigators11-13 have repeatedly proposed in the past several decades that deformation and fracture are mutually self-exclusive, and that the ability or inability of a material to deform plastically, i.e., to generate dislocations, is a major factor in determining whether the material will be ductile or brittle. Thus, in the present work an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. This article is principally concerned with the study of the relation between the propagation of ultrasonic waves and tensile deformation in a steel series which displays quite different toughness at room tempera-turk. changes in attenuation and velocity of ultrasonic waves have been measured as a function of strain during the deformation process. The results have been interpreted in terms of the vibrating string model for dislocation damping as developed by Granato and Lucke, and it has been found that some of the more subtle predications of the model are in good agreement with the experiments. This would be especially meaningful because most of the previous experiments in testfying the model were carried out with single crystals of high-purity materials and little work has been done with polycrystalline steel alloys. EXPERIMENTAL PROCEDURES AND RESULTS Specimen Materials. The tensile specimens used throughout this experiment were of two compositions selected from a series of Fe-Mo-0.77 pct Mn-0.22 pct C steels prepared for a ductile-brittle fracture transition study. One steel contains 0.21 pct Mo and the other 1.03 pct Mo. These two compositions were chosen for the present study because they possess quite different toughness properties at room temperature. The 0.21 pct Mo steel is quite ductile while the 1.03 pct Mo steel is rather brittle, as measured by the standard Charpy impact test. The alloys had been prepared by vacuum induction melting and chill casting in steel molds. The ingots were hammer-forged into 1/2-in.-sq bars from which tensile specimen blanks were cut. These blanks were first normalized under argon atmosphere at 1700°F and then reaus-tenitized and isothermally transformed at 1050°F to a bainitic microstructure. The chemical compositions, heat treatments, hardness measurements, and Charpy transition temperatures of the two steels are listed in Table I.

Jan 1, 1970

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By S. B. Twiss, P. R. Basford

The relationship between areas of iron powders, briquettes, and sintered compacts and tensile strength has been determined. It has been found necessary to distinguish between two types of areas which exist in such powders—a macroscopic area due to the shape and size of particles and a microscopic area due to pores and cracks in the surface. Only the macroscopic area, specifically the area due to particle irregularity, contributes to tensile strength; the microscopic area cannot be forced into contact with adjacent particles ond does not participate in bond formation. Of the two methods of area measurement employed in this study—permeability to liquids and gas-phase adsorption—only the former is useful for determining the roughness factor. A measure of this roughness, (area measured by permeability to liquid) -f- (orea of powder with the same size distribution, but made up of spherical particles), is shown to be uniquely related to tensile strength at constant density. The other important factors in determining the strength of sintered-metal compacts are the density and presence or absence of surface oxide. THE manufacture of metal parts by the process of powder metallurgy is an important and rapidly growing industry. Progress has been rapid and continuous, largely because of the excellent research in the field. Nevertheless, the process remains inherently complex and empirical. Several investigators have shown that the properties of the final compact must depend on many variables; namely, shape,' size distribution,"-" nd compositiona of the original particles, the pressure necessary to compress to the desired density, the density of the compact, the time and temperature of sintering, and so on. Through the application of some new techniques to the study of powders and compacts, and the correlation of a number of observations of known variables, the present paper attempts to clarify and simplify the underlying theory of the powder-metallurgy process. Any theory must start with the obvious fact that the strength of a compact, its most useful property, is due to the formation of welded areas between adjacent particles, and attempt to deduce what effect other variables will have on (a) the area and (b) the intrinsic strength of these welds. Such welded areas can be demonstrated by electron micrographs, as in Fig. 1. It was believed that (a) could be most directly studied by means of surface-area measurements on the original powders and on the compacts made from them; the area decrease should be related closely to the welded area. A representative group of eleven iron powders from commercial sources, and made by a variety of processes, was chosen for this study. In addition to the surface-area measurements, correlations were established between the tensile strength and all the known variables which might possibly affect it. The results are quite unexpected. They indicate that the situation is much simpler than the authors had anticipated. The strength of the sintered compact is determined, indeed, by no more than three variables; viz., the irregularity of the original particles, the density of the compact and, in exceptional cases, the amount of surface oxide. All three had been recognized previously as having some effect on the tensile strength, but in the absence of the special techniques and interpretations to be developed here, there could be no suspicion that they were the only relevant variables. Materials and Methods Material—All the iron powders were commercial products obtained from the Amplex Division of Chrysler Corporation. Powders A, B, C, and J were very pure electrolytic iron. Powder D was made from oxidized scrap reduced by heating with an excess of cast iron. Powder E was a high-grade iron ore reduced by hydrogen. Powder I was prepared by atomizing molten cast iron in an air blast, quenching the droplets in cold water, and crushing the coarse powder. Mill scale (oxide) is added and the mixture heated to reduce the high carbon content. The other powders were all prepared by reduction of iron oxides, such as mill scale. They

Jan 1, 1959

By JOHN S. HEARDING

ON the Minnesota Ranges, 600 million tons of material have been moved in the past three years to produce 172 million tons of direct-shipping iron ore. Increasing wage rates and cost of equipment and supplies, coupled with the larger amount of waste material to be moved in comparison with the quantity of ore make it imperative that tile industry adopt all practices and methods which will enable it to move earth at progressively lower costs. Drilling. Prior to and during the war practically all blastholes drilled were 6-in. in diameter and put down by drills using strings of tools weighing from 2000 to 3000 lb. Present trends indicate that heavier drilling equipment making 9-in. holes wit11 3000 to 6000 lb tools will be more economical. Holes up to 12 in. diameter will be made with this equipment. Forging and hardening practices for bits to increase footage is receiving attention. One manufacturer expects to market 9-in. bits having sintered carbide inserts in the reaming and cutting edges. Oxygen and oil to burn holes in the rock are being tested for making blastholes at a considerably greater speed than can be obtained with a blasthole drill on the same size hole. To dale, however, the cost has been prohibitive.

Jan 1, 1949

Jan 1, 1943

By Thomas R. Couzens

Jan 1, 1985

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By C Gunther

A preceding paragraph treats of the irregular manner in which ore deposits occur and the complex factors that control their distribution; the occurrence of metals in oreshoots in individual deposits is equally irregular, and the factors that control such segregation are equally complex. While the dimen¬sions of oreshoots in individual deposits may not be foretold with any degree of accuracy, the occurrence of ore in shoots is not accidental, but is controlled by laws some of which are understood. Any one familiar with permutations and combina¬tions who stops to consider the variety of factors that control ore deposition, and their varying relative importance, will admit that the science of economic geology must advance greatly before the occurrence of oreshoots may be predicted accurately in advance of exploration. The segregation of minerals in any oreshoot must be referred to some condition, or combination of conditions, local to the oreshoot as compared with the remainder of the deposit of low¬grade or barren minerals. Among the localizing factors that have been recognized are, in filled fissures, the amount and distribution of open spaces available for ore deposition, and in replacement deposits, the degree of brecciation giving access to the replacing solutions; the intersection of veins with other veins, dikes, sheeted zones, or porous strata; the impounding of solutions by impervious strata; and the differing precipitative influences of enclosing rocks. A large proportion of important and well ¬defined oreshoots, especially in deposits of deep-seated origin, are not assignable to any of these factors. While a knowledge of the character of oreshoots in general is important, a knowledge of the behavior of the known oreshoots

Jan 1, 1932

By F. M. Lewis, J. F. Myers

The crushing of ore, as defined by Taggart, is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes. . . . down to a final stage, employed for the reduction of the finest sizes. ... In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14-mesh limiting size which is either crushing or grinding. ..." Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a collventional fine-crushing machine. The experience of the authors is that a definite distinction must he made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine crushing machine it prepares relatively large amounts of ore for a subsequent fine grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. Pulp Movement and Action in Mill In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals.

Jan 1, 1947

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By Fred P. Dewey

IN preparing material for the exhibit of the National Museum at the New Orleans Exposition in 1881, it was decided to attempt to photograph the interior of a coal-mine, in order to get a strictly truthful representation of a thick coal-seam, and to show incidentally the methods of mining. While we have many drawings, both mechanical and artistic, illustrating the subject, they are not satisfactory for these purposes, simply because they are drawings. Aside from this, much interest attaches to pictures of inaccessible places, and the enlarged copies (30 inches by 40 inches) of the photographs we succeeded in obtaining, have attracted a large amount of attention from the visitors to the Museum. The Kohinoor colliery, Shenandoah City, Pa., was selected as most suitable for the attempt, principally on account of the fine exposure of the Mammoth bed, and the comparatively level character of the workings, in that colliery. This is one of the many anthracite-mines of the Philadelphia and Reading Coal and Iron Company. A detailed section of the fiftyfoot or Mammoth bed in this colliery is as follows: Feet. Inches. 1 0 Clod. 1 7 0 Coal. 1 0 Slate. Top Split. 8 0 Coal. 1 6 Slate divider.* 6 0 Coal. 1 0 6 Slate. 2 6 Coal. 0 5 Slate. 1 8 Coal. 1 2 Charcoal. 5 0 coal. 1 0 Bone and Coal. „ „ Coal. [ Bottom Split. 0 6 Bone and Slate. 3 0 Coal. 0 10 Bone and coal. 1 2 Coal. 0 2 Bone. 4 4 Coal. 0 1 Bone. 0 8 Coal.

Jan 1, 1888

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By R. E. Ricksecker, W. M. Baldwin, R. McC. Baker

INTRODUCTION THE development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1-3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of compressive stresses acting almost perpendicularly to the strip surface but vary [ ] ing in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting perpendicularly over the face of the tool. The elastic internal stress state in this case is complex-the principal stresses showing

Jan 1, 1948