Search Documents

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By R. W. Fountain, J. F. Libsch

ONSIDERABLE time and effort have been ex- pended recently in research designed to provide a better understanding of the solid state transformations leading to the permanent magnet qualities of many commercial alloys. The knowledge derived from these investigations has resulted in the development of new magnetic materials as well as improvements in some of the older materials. The permanent magnet qualities of the newer alloys having high residual inductions and high coercive force values, have been attributed to the precipitation of a second phase or an order-disorder transformation in a solid solution. The ternary Co-Fe-V alloys provide an interesting group of magnetic materials having a wide range of magnetic properties. The low vanadium alloys' possess soft magnetic properties similar to the binary Co-Fe alloys, while at higher vanadium contents (about 10 pct) interesting permanent magnet properties are obtained.2,3 Previous work by Nesbitt' on the ternary Co-Fe-V permanent magnet materials, resulted in the conclusion that the precipitation of a second phase, ?, was responsible for the permanent magnet qualities of these alloys. However, unlike the conventional precipitation hardening alloys, the ? phase, which is stable at high temperatures, is precipitated in the low temperature a phase upon aging. Recent work by Geisler and Martin"." has established that the order-disorder reaction inherent in the binary Co-Fe alloys is also present in the ternary Co-Fe-V alloys. On the basis of their investigation, it was proposed that ordering of the a phase is also a possible explanation of the mechanical and magnetic hardening in these alloys. Thus, it appears that the Co-Fe-V alloys are rather unique in that two solid state transformations are taking place which may account for the properties of these alloys. In view of these facts, the present investigation was undertaken to study the mechanism of mechanical and magnetic hardening in the 10 pct V-Co-Fe alloy with particular reference to the role of the ? phase; and to correlate the results of this study with other magnetic properties. In addition, the influence of increasing vanadium contents on the transformation of Co-Fe alloys was also undertaken to supplement the main objective of the investigation. Experimental Procedure The Co-Fe-V alloys used for study consisted of: 1—a commercial lot of Vicalloy I, a 10 pct V alloy, and 2—alloys prepared by powder metallurgy and containing 52 pct Co and 0 to 14 pct V, balance iron. The commercial alloy was received in the cast and forged condition and was used primarily for the detailed study of hardness, electrical resistivity, and magnetic properties of the 10 pct V alloy. The powder metallurgy alloys were prepared from electrolytic iron, commercial cobalt, and ferro-vanadium powders. The processing cycle was as follows: 1—Elemental powders were weighed and mechanically mixed for 24 hr. 2—Mixed powders were pressed at 60,000 psi into the form of bars 5/8 x 5/8 x 5 in. 3—Bars were sintered in an atmosphere of purified dry hydrogen for 24 hr at temperatures ranging from 1380" to 1340°C, depending upon the vanadium content. The as-sintered bars were cut in half; and one half was machined to 7/16 in. diam for thermal analysis. The remainder of the bar was hot forged to approximately 0.050 in. for X-ray diffraction analysis. Additional details of sample preparation are presented subsequently according to the type of test performed. Thermal Analysis Measurements One of the simplest and most widely used tools for determining phase relations as they change with temperature and composition is to study the rate of change of temperature of a material as heat is supplied or extracted at a constant rate. The thermal analysis method used in this investigation is the inverse-rate method described by Smith.'

Jan 1, 1954

By C. S. Westerberg, C. P. Heiner

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By J. W. Rutter, K. T. Aust

The migration of individual, large-angle grain boundaries has been studied as a function of tempereature and solute concentration in specimens of zone i.e filled lead containig very small additions of silver and of gold. Tile results are compared with various the-ories of grain boundary migration and with observations made prev.iorlsly of grain boundary migration in similar specimens of zone-refined lead containing tin additions. A previous investigation by the authors dealt with [he temperature dependence of grain boundary migration in bicrystals of zone-refined lead containing small additions of tin.' It was shown that tin additions as low as a few parts per million cause a large decrease in the grain boundary migration rate at any given temperature, as well as a marked increase in the temperature dependence of the migration rate. It was found that existing theories of grain boundary migration. based on the motion of dislocations. or upon the concept of atom transfer in groups across the boundary (group process theory). or upon the control of grain boundary motion by volume diffusion of impurity atonls along with the boundary. are incapable of accounting for the observations. The single process theory of grain boundary migration. which is an absolute reaction rate calculation based on the transfer ui atoms singly across the moving boundary, was found to predict the migration rate reasonably well for a number of boundaries whose motion was shown to be very little influenced by impurities, but not for boundaries whose illation was influenced markedly by impurities. It was concluded that the elementary process of grain boundary migration involves the activation of single atoms during transfer across the boundary. and that inadequate knowledge is available to permit the influence of impurities to be properly taken into account. The present study was initiated to check the validity of the above conclusions with other alloy systems, namely high-purity lead with small additions of silver and of gold. Both silver and gold diffuse faster. and with a lower activation energy of volume diffusion. than does tin in lead;' consequently, a study of the effects of silver and gold on grain boundary migration in high-purity lead offered a means of testing theories of boundary migration based on bulk diffusion of the solute (eg. ref. 3). In addition. it was hoped that the present work, in comparison with the results for tin in lead, would provide information concerning which factors are important in determin- ing the interaction between solute atoms and a grain boundary. EXPERIMENTAL PROCEDURE The preparation of bicrystals of zone-refined lead, with various silver or gold additions, was identical to that previously described for the lead-tin alloys.''4 Each bicrystal consisted of a striated crystal which was grown from the melt. and an adjacent striation-free crystal which was introduced by artificial nucleation and growth.''4 The striation or lineage substructure in the melt-grown crystal provided the driving force for grain boundary migration. During the preparation of striated single crystals by growth from the melt, it was found that silver or gold concentrations as low as 2 or 3 ppm by atoms were sufficient to cause formation of the hexagonal cell structure. which is due to the presence of impurity, during freezing. This structure is revealed on the solid-liquid interface by decanting the liquid during freezing. The hexagonal cell structure was observed previously4 in zone-refined lead crystals with tin contents above approximately 200 ppm by atoms. These concentrations of silver, gold, or tin are in agreement with the predicted amounts required for cell formation in lead,5'6 under the present conditions of freezing.4 The absence of cell structure at decanted interfaces, therefore, served as a useful indication that the silver or gold contents were less than 2 or 3 ppm by atoms in the specimens as grown. It was found that grain boundary migration occurred only very slowly when the solute content approached that necessary for cell formation. As a result, the present experiments were conducted with silver or gold additions less than 1 ppm by atoms. This impurity level is well within the solid solubility limits for silver and gold in lead.7 The annealing treatments, measurements of grain boundary velocities, and orientation determinations were carried out as described previously.' However. each bicrystal was also chemically polished in a solution consisting of 8 parts glacial acetic acid and 2

Jan 1, 1961

By V. Pasupathi, R. E. Hummel, J. W. Koger

Specimens of P1 brass were plastically deformed at room temperature to various degrees of deformation and subsequently cooled in order to transform them to low-temperature martensite. Deformation shifts Ms. A, , and the temperature of minimum resistivity to lower temperatures, and also decreases the temperature coefficient of electrical resistivity. These properties change rapidly up to about 15 pct reduction but vary very little with higher deformation. The possible relationships between martensite formed by deformation and the M, temperature of low-temperature martensite are discussed. Evidence is given that deformation martensite delays the formation of low-temperature martensite. BETA' brass undergoes at least two different types of martensitic transformations. One of these transformations (B1- B2) was first observed by Kaminski and ~urdjumov' and occurs when 81 brass with a zinc content between 38 and 42 wt pct (quenched from the single-phase region) is cooled below room temperature. Jollev and Hull' determined the structure of 0" from X-ray and electron-diffraction data as ortho-rhombic. Kunze came to the conclusion that the super-lattice cell of 0" is one-sided face-centered triclinic (pseudomonoclinic). The second martensitic transformation (B1-A1) occurs when the specimens are deformed at or somewhat above room temperature. This type of martensite will be called deformation martensite. Horn-bogen, Segmuller, and Wassermann4 determined the structure of deformation martensite to be bct. (An intermediate phase, az, occurs before the final phase appears.) At deformations higher than 70 pct, a, transforms into a.4 A critical temperature Md exists above which no transformation occurs during deformation and is estimated to be around 400°C in P1 brass.5 This martensite has elastic properties.6 When the sample is stressed, martensitic plates appear; when the stress is released, the plates disappear. The present paper studies the effect of deformation martensite on the formation of low-temperature martensite. The experiments involved samples of 8, brass which were plastically deformed by various amounts and were subsequently cooled below the transformation temperature. EXPERIMENTAL PROCEDURE The 13 brass investigated was made from 99.999 pct pure copper and 99.9999 pct pure zinc and contained 38.8 wt pct Zn. The specimens, consisting of foils 0.1 mm in thickness, were heat-treated at 8'70°C for 15 min in an argon atmosphere and then quenched into ice water. They were then deformed by cold rolling and subsequently cooled at a rate of 1°C per min. The martensitic transformation that occurred during cooling was followed by electrical resistivity measurements. The resistance measurement technique and its accuracy have been described in a previous paper. Because the transformation 81 —-8" occurs below room temperature, the samples were placed in a cryo-stat which contained isopentane as a cooling medium. The isopentane was cooled by liquid nitrogen pumped under pressure through a 15-ft coil of copper tubing which was immersed in the isopentane. The nitrogen flow was regulated by a temperature controller using two thermistors in the cooling medium. The cryogenic liquid could be heated with an immersion heater. The useful temperature range with this device was from +25° to approximately -155~C. EXPERIMENTAL RESULTS Resistivity Measurements. The following abbreviations are used in this paper to label the characteristic temperatures during the martensitic transformation. M, is the starting point of the martensitic transformation and is defined as that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line. Mf is the temperature at which the martensitic transformation is completed. On reheating, the transformation from martensite to the parent phase starts at a temperature A, and ceases at a temperature Af. Fig. 1 presents five different resistivity vs temperature curves corresponding to the transformation of brass from Dl to 8" after different degrees of reduction in thickness. The following observations can be made from these curves. 1) With increasing degree of deformation the Ms temperature is shifted to lower temperatures. This shift ranges up to 35°C compared to the undeformed state. This is also indicated in Fig. 2, where AM, (the shift of Ms, compared to the undeformed state) is plotted vs the degree of deformation. AM, increases rapidly until a reduction of about 15 pct is reached. With higher deformations, no additional increase in AM, was found. 2) With increasing degree of deformation the temperature of minimum resistivity (M) is also shifted to lower temperatures. The shift, attains a maximum of about 61°C compared to the undeformed state. In Fig. 3, AM is plotted as a function of deformation. It can be seen that, as in 1 above, AM increases rapidly and no further shift of M occurs for deformations greater than 15 pct. 3) The temperature coefficient of resistivity, is given by the slopes (dp/dT) of the linear portions of

Jan 1, 1969

By C. P. Heiner, C. S. Westerberg

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By W. M. McKewan, R. G. Olsson

In order to improve the understanding of the iron oxide reduction mechanism, the rate of equal molar diffusion of hydrogen and water vapor was measured through disks of porous iron and alumina. The measuretneizts were made at atmospheric pressure at 800°, 900- , and 1000°C. It is shown tint the reduction of dense hematite pellets with hydrogen at these temperatures and at atmospheric pressure is to a great extent limited by gaseous diffusion between the bulk-gas phase and the iron-wustile interface. THE investigation of the reduction of iron oxides with hydrogen has been the subject of numerous papers. Although the effects of temperature, pressure, and gas composition on the rate of iron oxide reduction have been studied, the actual mechanism of the reduction process has not been definitely determined. As a means of improving the understanding of the mechanism, the rate of equal molar counterdiffusion of hydrogen and water vapor was measured through porous iron and porous alumina disks at reduction temperatures. The alumina was used as a basis of compari-son because its pore structure is homogeneous and independent of temperature. The porous iron was prepared by the reduction of dense hematite disks with hydrogen at the temperature of the subsequent diffusion experiment. The hematite disks were made from pellets that were identical to those used by McKewan1,2 in his study of iron oxide reduction with hydrogen. In these investigations the weight loss and rate of movement of the various interfaces were measured as a function of the reduction temperature and gas composition. With these reduction data and the presently reported diffusion data it is possible to determine the importance of H2-H2O transport between the bulk-gas phase and the Fe/FeO interface to the reduction of dense hematite. APPARATUS AND PROCEDURE A porous iron or alumina sample was held in the base plate of a sealed canister containing porous granular wustite, as illustrated schematically in Fig. 1. The canister was suspended from an automatic recording balance in a vertical tube furnace through which flowed hydrogen and water-vapor mixtures of known composition at atmospheric pressure (0.96 atm). Hydrogen from the gas stream diffused through the porous sample, reducing the wustite in the interior of the canister. The water vapor that was formed diffused back to the gas stream. The rate of diffusion was determined from the recorded weightloss data. The furnace, automatic balance, and gas-metering equipment have been described previously.2 The main body of the canister and the tubing extension were made of stainless steel while the base plate was made of high-purity iron. The main body of the canister was % in. in diam. It held approximately 6 g of porous granular wustite that was prepared by reducing 0.1- to 0.2-cm-diam specular hematite particles at 900°C with an H2-H2O mixture of a composition near the iron-wustite equilibrium value. The upper end of the 1/8-in.-diam tubing extension was sealed with a segment of plastic tubing and a tubing clamp. The temperature at the top of the furnace was sufficiently high so that no water vapor condensed inside the extension. In the experiments with porous iron, iron oxide samples were prepared from reagent-grade hematite that was pressed and sintered in a manner previously described.' The resulting pellets had a density of 5.15 ± 0.05 g per cu cm. Each pellet was centerless-ground

Jan 1, 1967

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (''segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.' Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.'s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations' and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.' GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers'-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,' reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

Jan 1, 1943

Jan 1, 1943

By W. L. Phillips

Stress-train curves were obtained for single crystals of silver, Ag-5 pct Zn, Ag-10 pct Zn, and Ag-20 pct Zn tested in tension and shear at 78°, 195°, and 297°K. At room temperature the critical resolced shear stress gC increased, the length of' the easy-glide region increased, and the rate of' work hardening dwving easy glide decreased with increasixg zinc concentration. The change in the ratio of uc at room temperature to that at lower temperatures was significantly greater for the alloys than for pure silver. It was found that an increment in stress was necessary to continue slip when the slip direction was rotated 60 deg. The magnitude of this increment increased with strain for all alloys, increased with zinc concentration for a given strain, and for a given strain increased with decreasing -temperature. DESPITE its practical importance in improving the mechanical properties, alloying is not fully understood. Except for copper alloys few sets of systematic data are available. Von Goler and Sachs' studied the deformation of Cu-Zn alloys of increasing zinc content and found that, for dilute alloys, the critical resolved shear stress increases linearly with concentration. The range of easy glide was found to increase with increasing zinc content. Schmid and seliger,2 Sachs and Weerts,3 and Osswald4 have shown that with Mg-A1, Au-Ag, and Cu-Ni crystals, respectively, the critical resolved shear stress also varies linearly with concentration. More recently, Linde and his coworkers have investigated the variation of the critical shear stress of copper alloyed with tin , antimony, indium, germanium, silicon, nickel, and gold. They found that the slope of the critical resolved shear stress is related to the change of lattice parameter with composition, and also to the difference in Goldschmidt's atomic diameter between solvent and solute atoms. Garstone, Honey-combe, and creetham6 have shown that similar relationships can be found for small additions of silver, gold, and germanium to pure copper. They found that, with increasing silver or gold concentration, the critical shear stress for glide is increased by alloying, and so is the range of easy glide, which reaches as much as 60 pct for 0.50 pct Ag alloy and 0.62 pct Au alloy, as compared to 6 pct for pure copper of similar initial orientation. They also found that the alloying additions had little effect on the rate of hardening during easy glide, the slope scarcely changing with increasing alloy content. General secondary slip was detected only when the crystals began to harden rapidly. Although the slip appeared to be very fine in the early stages of deformation, coarser slip bands were formed towards the end of the extensive easy-glide range. The present investigation describes the deformation characteristics of single crystals of Ag-Zn containing different concentrations of zinc. Tension and shear testing were used for this study. EXPERIMENTAL PROCEDURE The method of growing the single crystals, sample preparation, and method of testing have been described in detail previously.' EXPERIMENTAL RESULTS A) Tension-Room Temperature. The initial orientations and stress-strain curves of single crystals of silver, Ag-10.0 pct Zn, and Ag-20.0 pct Zn are shown in Fig. 1. It is evident that there is considerable change in the stress-strain characteristics as a function of zinc concentration. The effects of zinc concentration on the critical resolved shear stress for both CU-zn8 and Ag-Zn alloys are summarized in Fig. 2. At all concentrations the resolved shear stress of the Cu-Zn alloys is higher than that of the Ag-Zn alloys. The resolved shear stress increases parabolically as a function of composition for both alloy systems. The length of easy-glide region increased with increasing zinc concentration, Fig. 3b). As the length increased the slope (do/de) decreased slightly, Fig. 3(b). Metallographic investigations demonstrated two significant effects of increasing zinc concentration. First, the amount of clustering increased, compare Figs. 4(a) and (b). The slip lines changed from uniform in pure silver to clustered in the Ag-20 pct Zn and Ag-30 pct Zn alloys. Second, the amount of cross slip decreased as the amount of clustering decreased.

Jan 1, 1968

By L. A. Rapoport, W. J. Leas

The original Burkley-Leverett theory has been extended and a more detailed formulation of the waterflood behavior in linear horizontal systems is presented. Particular consideration has been given to the evaluation of capillary pressure effects and differential equations permitting an explicit evaluation of these effects have been derived. On the basis of the developed theory it is recognized that the flooding behavior is dependent upon the length of the system and the rate of injection. At the same time it has been determined that systems of different lengths yield the same flooding behavior if the injection rates and or the fluid viscosities are properly adjrrsted or "scaled." It has also been found that the sensitivity of the flooding behavior with respect to rate and length decreases as any one of these {actors increases in value and that for sufficiently long systems and high rate.; of water injection the flooding behavior becomes independent of rate and length. or "stabilized." To such stabilized conditions the theory formulated by Buckley and Leverett is applicable. A number of laboratory flooding tests have been made and good agreement Iraq been found between theory and experimental observations. The experimental results are discussed and it is shown that under field conditions the flooding behavior is usually stabilized. As a result of these finding; a procedure is indicated for evaluating field performances either on the basis of tests performed with commonly available core samples or by means of calculations using relative permeability data INTRODUCTION In recent years the development of methods for evaluating oil recovery by waterflooding has been the object of considerable research. A theoretical analysis of the mechanisms involved in the displacement of immiscible fluids was originally established by Buckle!- and Leverettl and experimental investipatio~~s have been made by numerons workers." Many of the experimental results are in mutual agreement and bear out several significant features of the flooding mechanism as predicted by theory. Thus it lias been generally recognized that a flood corresponds to the movement of a steep saturation hank or "front" (primary phase), followed by additional gradual oil displacement (subordinate phase). It has also been found that for any porous medium the flooding behavior is largely dependent upon the oil-water viscosity ratio and that for increasing values of this ratio the relative importance of the primary displacement phase decreases while that of the subordinate phase becomes more pronounced. Although the studies to date have clarified certain aspects of the flooding process. they have given rise to observations of a somewhat contradictory nature that cannot he explained in terms of the original theory. These observations pertain mainly to the effect of injection rate or pressure gradient upon recovery. Some investigators report laboratory tests that indicate incresing oil recoverieq with increasing rates of water injectill, others find the flooding behavior to be independent of and other. mention lower oil recoveries with increased injection rates.3 The conflicting evidence indicated above creates considerable uncertainty with respect to laboratory testing procedures and the utilization of the resulting data for field evaluations. The principal purpose of this paper, then, is to resolve these Uncertainties by means of a comprehensive theoretical and experimental investigation of the flooding meanism. THEORETICAL DEVELOPMENT Derivation of Flooding Equations The mathematical description of transient flow phenomena is based upon the consideration of the various processes occurring during an infinitesimal time interval in an infinitesimal volume element and upon the correlation of these processes with those occurring in the adjacent elements. The volume elements are defined as being infinitesimal in comparison to the overall dimensions of the porous system, yet each sufficiently large so aS to encompass the full range of pore openings encountered throughout the system. If a porous system can arbitrarily be subdivided into an infinite number of volume elements all possessing the same distribution of pore openings and if this distribution is unformly continuous. the system may be said to be homogeneous. Such a homogeneous porous medium is considered in the present studivs. It is furthermore postulatecl that only oil and water are present in the pornu wediu. that they act a- totally incompressible and immiscible fluids. and that gravity effects are negligible. In n linear flow system of unit cross sertional area. as treated here. the infinitesimal volume element.; to he considered are cylindrical ".slices" of thickness dx. oriented perpendicularly to the direction of flow. The equations applicable to any such volume element. at my time. describe the movement. of oil and water across the element:

Jan 1, 1953

By R. C. McFarlane, T. D. Mueller, J. E. Walstrom

In evaluating uncertainty, experiments are usually performed repeatedly and then conclusions are drawn from the distribution of results. With the advent of high-speed electronic computers, it is possible to perform experiments using mathematical models constructed to simulate complex experiments or operations. Statistical methods are then applied to the results of the simulated experiments. This procedure forms the busis of this paper. Demonstrated is the need for properly accounting for uncertainty in petroleum engineering problems. How uncertainty affects solutions is evaluated in three example illustrations. The method used to evaluate uncertainty in petroleum engineering studies is the Monte Carlo simulation procedure.'-" INTRODUCTION The solution to most technical problems may be derived from interrelationships among several quantities called variables or parameters. There may be only a few variables or several hundred. Interrelationships among parameters may be explicit or implicit, well established or only approximate. Some variables that fully or partially depend on the magnitude of others are called dependent variables. Input variables for most practical problems are not precisely known; there is usually an uncertainty in their value. The degree of uncertainty may vary from one variable to another. Variables that are known accurately are called determinates.' For instance, the gravity of crude obtained from a particular pool may be known precisely, and therefore is a determinate. The degree of precision with which a quantity can be determined increases as data describing the pool are accumulated during the development of the field and the producing life of the pool. The uncertainty of a parameter may result from difficulty in directly and accurately measuring the quantity. This is particularly true of the physical reservoir parameters which, at best, can only be sampled at various points, and which are subject to errors caused by presence of the borehole and borehole fluid or by changes that occur during the transfer of rock and its fluids to laboratory temperature and pressure conditions. Uncertainty may also result in attempting to predict future parameter values. This type of uncertainty is particularly evident in investment analyses involving future costs, prices, sales volumes and product demand. Uncertainty in the solution to investment problems is often called risk, and its study is called risk analysis.' Uncertainty also enters into biological and sociological analyses in which indeterminate factors are often important due to limited control of the experimental material. It is customary, in evaluating uncertainty, to perform repeated experiments and to draw conclusions from the distribution of the results of these experiments. With the advent of the high-speed electronic computer, it is possible to construct mathematical models which simulate complex experiments or operations and to perform the experiments repeatedly, utilizing the models. Statistical methods are then applied to the results of the simulated experiments This method forms the basis of the investigation reported here. PROBABILITY DISTRIBUTIONS FOR VARIABLES The uncertainty in the value of a variable may be indicated by a probabilistic description accomplished by expressing the quantity by a probability distribution. Many recognized probability distributions can be used to describe physical quantities. Recent studies used various types of distributions to describe core analysis data.',' However, for the examples in this paper, the uniform and triangular distributions are believed to reasonably approximate the data used (Fig. 1). The uniform distribution confines the variable between an upper and a lower limit. The variable may lie anywhere between the two limits. This distribution is used when no one range of values for a variable is more probable than any other, but information or intuitive reasoning indicates the variable will lie somewhere between the chosen limits. The triangular distribution is used for a variable when more data are available to indicate a central tendency of distribution. This allows postulating a "most likely" value to the distribution and upper and lower limits. In this case, as for the uniform distribution, the variable is not expected to assume a value less than the lower limit or greater than the upper limit. However, with improved quality of data it can be postulated that the variable will tend to assume a value close to the most likely value, and that there will be a decreasing probability for values away from the most likely value. The area under either of these probability distributions is equal to unity since it is assumed that there is a 100 percent probability that the variable will lie somewhere under the curve. An ordinate erected at any particular value of the variable divides the area under the curve into two parts: the area to the left of the ordinate represents the probability that the value of the variable will be equal to or less than the value of the variable at the position of the ordinate, and vice versa. The probability is zero that the variable will have any specific deterministic value. If two ordinates are drawn for any two values of the variable, the probability that the variables will have a value lying between these ordinates is equal to the area under the curve lying between the ordinates.

By J. W. Wolfe

The Benedict-Webb-Rmbin equation of state was used in digital computer programs to make rapid determinations of natural gas equilibrium phase compositions. Mixture components were the nine hydrocarbons, methane through heptane. Comparative tests were made with data from field separators, plant exchangers and literature sources. For most tests made, the B-W-R equations predrcted component K-vallles, mixture enthalpies and phase aensities within tile accuracy of available correlations for rune-component mixtures: significant deviations were noted when mixtures contained components heavier than heptune. INTRODUCTION Rapid, accurate methods for calculating the properties of hydrocarbon mixtures are needed for predicting the behavior of natural gas processes. For example, because of the common use of two-phase separation methods in gas proccssing, calculations must be made for the density and composition of equilibrium vapor and liquid phases. In addition, predictions must often be made for the temperature and pressure changes associated with the flow of single- and two-phase natural gas fluids through heat exchangers, chokes and turbines. The complex nature of non-ideal mixtures makes rigorous calculations for these natural gas properties difficult and time-consuming. Natural gas properties have conventionally been determined with generalized data correlations. These correlations, such as the K-values presented in the NGAA Equilibrium Ratio Data Book, are usually based on some average property of the mixture and have proven to give satisfactory estimates for the properties of most oil and gas systems. Digital computers, however, have not only increased the utility of these correlations, but also have made practical the use of equations of state for calculating the properties of natural gases. Potentially, if basic pure component data are available, all the desired thermodynamic properties of mixtures can be derived from a single equation of state describing the mixture. Currently. the best equation of state for describing the behavior of pure, light hydrocarbons over single-and two-phase regions, both below and above critical pressure, is that of Benedict. Webb and Rubin.' The equation contains eight constants which are determined by empirically fitting the equation to pure-component PVT data. Benedict and his co-workers presented the clevelopment of their equation as early as 1940.2 The B-W-R equation is a modification of the Beattie-Bridgeman equation of state and gives better PVT predictions than the Beattie equation at densities above the critical density. Benedict et al. made the equation applicable to mixtures by relating the mixture constants to composition and the constants for pure compounds. These authors, in a serics of articles in 1951,' showed the accuracy of the B-W-R equation when applied to light hydrocarbons and their simple mixtures, and demonstrated the equation's utility for making vapor-liquid equilibria calculations. Since its inception, the B-W-R equation has been the subject of many papers. Numerous additions and modifications have been proposed,'-',"'-':' the purpose of most being to improve the equation's ability to predict PVT properties of specific mixture systems. In 1959, Opfell, Pings and Sage summarized much of the work on the B-W-R equation in their book on equations of state." Since natural gases are primarily mixtures of light hydrocarbons, the B-W-R equation is a natural choice for an equation of state to compute both phase equilibria and thermodynamic properties of natural gases. Consequent-

Jan 1, 1967

By AIME AIME

AN entirely new type of classifier is being put on the market by The Dorr Co., following three years of development and the experimental use of thirty machines of the improvement design in various parts of the world. It is known as the Multizone classifier. Compared with the older type the lower or overflow end has been decked over and is surmounted by one or more circular overflow columns. Feed is introduced near the middle of the machine and passes downward and under a vertical baffle, then along the underside of the deck to the base of the overflow columns. Under the baffle there is a restricted turbulent zone of high pulp velocity which holds the fine and critical size particles in suspension, preventing

Jan 1, 1937

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

By Oliver C. Ralston

This paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Pfoutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work, while connected with the station in one way or another. Lead Metallurgy Popularly Supposed to be Without Problems In lead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that lead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the three years of work of the Salt Lake Station, the following classification of problems in the metallurgy of lead has been made: Oxidized Ores. 1. Ores containing only lead. 2. Ores containing lead and silver or gold. 3. Ores containing lead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some lead. 2. Ores of complex zinc-lead-iron sulphides. 3. Complex sulphides containing precious metals.

Jan 1, 1918