Search Documents

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920

Jan 1, 1892

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By N. A. Stockett

Southeast Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. Tons World production................. 2,000,000 United States Production .........- 460,000 Southeast Missouri production..... 142,000 The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's in in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averaging over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. I, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,980,000 short tons of pig lead. • About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of st. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in st.Francois county, Prospecting In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jack-hamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling—100-ft. centers of holes, and sometimes less—is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more. To date, geophysical and other methods of prospecting, apart from diamond and Mining Practices of the St. Joseph Lead Company in Southeast Missouri

Jan 1, 1943

By N. A. Stockett

Southeast Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. Tons World production................. 2,000,000 United States Production .........- 460,000 Southeast Missouri production..... 142,000 The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's in in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averaging over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. I, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,980,000 short tons of pig lead. • About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of st. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in st.Francois county, Prospecting In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jack-hamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling—100-ft. centers of holes, and sometimes less—is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more. To date, geophysical and other methods of prospecting, apart from diamond and Mining Practices of the St. Joseph Lead Company in Southeast Missouri

Jan 1, 1943

By Robert Anderson

The diffraction of x-rays by cold-worked and heavily polished surfaces of metals gives, no evidence of an amorphous state and typically perfect crystallographic diffraction' patterns are obtained. Severely cold-worked metals, reduced as much as 98 per cent. in area, give true crystallographic diffraction patterns, and polished surfaces of large single crystals of metal give typical crystallographic patterns. The conclusion is drawn, on basis of x-ray evidence, that metals are fragmented on cold work and polishing and not amorphized. THE purpose of this paper is to report evidence, regarding, metal: structures, that is contradictory to the amorphous-metal, hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed, by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby's explanation, is well known-and does not' require discussion here, but it is advisable to seek the precise meaning of,., the term "amorphous." According to Beilby, "amorphous means. Non-crystalline in the most intimate sense of the word'; the molecules are not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when, the .crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that ;which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved.

Jan 1, 1925

By L. A. Weitzenkamp, N. M. Bashara

A study of the electrical conductivity of gold films less than 200 in thickness indicates a negative temperature coefficient of resistance and a thermal actiuatlon energy of less than 0.25 ev. The films consist of discrete metal islands of linear dimensions from a few angstroms to 1000A. Films were able to withstand applied fields up to 60,000 v per cm before breakdown occurred. A model for the conduction mechanism is proposed which involtes a Potential barrier due to work junction, irriage forces , and an electrostatic potential arising from separating an electron from a neutral island leaving behind a positively charged metal island. Activation energies of less than 0.25 ev ave consistent with this model, which includes a tunneling andor Thermal mechanism for conduction between the separate metal islands. An apparent satuvation effect in conductivity at high fields is observed experimentally. The saturation effect may be explained by the influence of the electrostatic contribution to the potential barriers for the transition through several islands adjacent to the original island which was activated to give up an electron. The proposed model gives Poor quantitative agyeement for the intermal electrical field between islands. ThIS paper will relate the structure of discontinuous metal films to the electrical properties and will emphasize the following topics: 1) the relation of the conduction mechanism to particle size and a comparison of particle size from electrical measurements with electron-microscope studies; 2) the saturation of the conductivity at high electric fields; and finally, 3) a comparison between the external field applied and the apparent field between particles. che- latter comparison points to a need for a modification in the model for the conduction mechanism first proposed by orter' and expanded by Neugebauer and webb2 which will be dealt with in the discussion. The paper is based on results on gold films on glass microscope slides. The clms were vacuum-evaporated and were about lOOA thick, thickness being measured by interferometry. It has been observed that metal films of this thickness do not exhibit bulk metallic conduction. Films thinner than some critical thiclmess, depending upon substrate temperature and other factors, have conductivities which increase with increasing temperature with thermal activation energies of less than 0.25 ev. Electron-microscope studies3 have shown that these films consist of discrete metal islands having linear dimnsions from a few angstroms to approximately 1000A. When the metal is being vacuum-deposited on the substrate, islands on the order of a few angstroms appear first. As the deposition continues the islands may tend to agglomerate into larger particles and may eventually grow together into a continuous film,3''' In our tests the conductivity of the gold films was found to be about ten orders of magnitude less than the bulk conductivity of gold. When oxygen was introduced into the test chamber the conductivity decreased by a factor of about one-third. This can be related to an increase in work function for gold caused by adsorption of oxygen, as reported by Oullet and Rideal.s Exposure to an atmosphere of water vapor caused an increase in conductivity by a factor of 2 or 3 when a low field was applied. When the films were exposed to water vapor under a high field the conductivity increased by as much as two orders of magnitude. The activation energies measured were much less than the work function for gold, 0.25 ev or less, with the smaller activation energies observed for thicker films. It will be shown that the activation energy is a function of particle size and spacing. In general the model for the potential between metal islands would include the effective work function, the image force, the applied field, and an electrostatic term. The electrostatic contribution arises from the potential required to separate an electron from a conducting sphere. According to Neugebauer and webb2 the maximum potential due to the field and the electrostatic term only is

Jan 1, 1967

By A. J. Teplitz, R. J. Goodwin

A new type water shut-off for use in air drilling has been developed. The method has been 99 to 100 per rent effective in several different formations of inter-ranular-type porosity. Since costs for materials, time and equipment used are relatively small, the process should extend economies of air drilling to many new areas. The treatment involves a new technique for forming a water-inroluble precipitate within the pores of a rock. Advantage it taken of the difference in mobility of a liquid and a gas in porous media to achieve the greatest volume of precipitate in a given pore. Reactants selected for the laboratory (2nd field tests were aluminum sulfate solution and gaseous ammonia. This process has been tested in both intergranular and fractured-type porosities. It has consistently shut-of between 99 and 100 per cent of the water flowing from formations having intergranular-type porosity and perrlreuhilities ranging from a few millidarcise to over a darcy The treatment is not particularly suitable for shutting-off water from fractured formations although plugging of the order of 50 per cent or greater has been achieved in all such applications. Among advantages of the treatment are: (I) no reaction waiting rime after a relatively short placement time, (2) a low mate-rials cost of about $3/f1 of hole treated, (3) use of common service-type equipment for treatment, and (4) no unusual requirements for mixing and placement. INTRODUCTION In rotary drilling with air or gas it has been possible to increase bit life by tenfold and more than double rate of penetration over corresponding performance when drilling with mud. These factors have amounted to as much as 22 per cent savings on total cost of drilling a well. However, these advantages are rapidly lost when water is encountered in an air- or gas-drilled well because water interferes with the removal of cuttings from the hole and also gives rise to other difficulties. In attempting to combat water troubles, operators have commonly resorted to such measures as mist drilling, treatment with cement or chemicals, converting to conventional mud drilling, or setting casing. In many cases these measures have either been costly or ineffective. In an effort to overcome this problem, studies were undertaken to develop an effective and economical water shut-off technique for use in formations possessing inter-granular-type porosity. Extensive laboratory experimentation finally led to a unique method for producing a water-insoluble precipitate within the pores of a sandstone. The unique part of the treatment is use of a liquid and a gas to form the precipitate, and in this case the reactants used were aluminum sulfate solution and gaseous ammonia. The reaction between these two materials is shown in the following equation. Al2 (SO1)3 - 18 H20 6NH2? saturated Water- Solution Cat 2A1(OH)3 . n H20 3(NH4)2SO • n H20 Solid Solid That is, a solid precipitate consisting of aluminum hydroxide and ammonium sulfate is formed when ammonia reacts with aqueous aluminum sulfate. The aluminum hydroxide is insoluble in water and the ammonium sulfate, though soluble, can only be removed from the formation pores by diffusion—an extremely slow process. Although the precipitate formed by the reaction is not particularly firm, great strength is not needed for a precipitate to bridge and plug intergran-ular-type porosity. A flow path in such a system is extremely tortuous and involves a great variety of pore

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By J. A. Berger, G. W. Wiener

Several transition metal nitrides have been prepared and their saturation magnetization determined. On the basis of an atomic model of ferromagnetism involving a consideration of nearest neighbor interactions and the assumption that all atomic moments of the metal point in the same direction, it appears that the nitrogen interacts with d-shell of the transition metal in such a way as to reduce the magnetic moment. THERE is a large class of materials having metallic properties which are formed by a combination of hydrogen, boron, carbon, oxygen, or nitrogen with the transition metals. Several attempts have been made to establish the type of metal-nonmetal bonding in these interstitial alloys because it is believed that many of the physical properties of these materials are determined by the characteristics of this bond. Several of these alloys are ferromagnetic, and thus a powerful method is available for investigating the structures in a direct manner by measuring the saturation magnetization. The latter is a fundamental property of ferromagnetic metals and alloys which depends primarily on the electron distribution surrounding the atom. For the first row of transition metals, this refers specifically to the 3 d-shell. Since bonding involves the electronic configuration between atoms, there is reason to suppose that a relationship exists between ferromagnetism and bond type. In the case of the interstitial structures studied in this work, bonding will refer to the distribution of electrons between the transition metal and the nonmetal. Since these alloys have metallic properties, it is further proposed that any bonding interactions will involve the outer p-shell of the interstitial element and the incomplete d-shell of the transition metal. If this is the case, then the relationship between ferromagnetism and metal-non-metal bonding is established qualitatively. In order to investigate the subject quantitatively, certain transition metal nitrides were chosen because they have simple crystal structures, are ordered alloys, and are ferromagnetic. They also have sufficiently high saturation magnetization to be of technical interest. Currently there are two major theories of ferromagnetism, each of which has been applied to the interpretation of the saturation magnetization in terms of atomic structure. They are usually referred to as the band theory and the atomic theory. The former has found widespread application to the study of pure metals and certain solid-solution allays. However, it has not been applied to the interstitial structures or ordered alloys because it does not interpret the properties directly in terms of the crystal structure. The atomic theory on the other hand is especially suited to the study of interstitial structures because it permits an interpretation of ferromagnetic phenomena in terms of the crystal geometry. As has been pointed out previously, the nitrides have simple ordered crystal structures and, therefore, the choice of the atomic theory for the interpretation of the data is a natural one. One of the prime difficulties with the atomistic theory is that its mathematical justification is much more difficult, and for this reason its general acceptance will depend to a large extent on the value it has in explaining and predicting the results of experiment. Before the presentation of the theoretical basis for understanding the metal-nonmetal bond, it is useful to review the ideas existing prior to this work. Four different interpretations have been given to the metal-nonmetal bond. These are summarized as follows: 1—acceptance of electrons by the nonmetal from the incomplete d-shell of the transition metal, 2—transfer of electrons from the nonmetal to the incomplete shell of the transition metal, 3—no exchange of electrons between the two atoms, and 4— a resonating type of bond involving the p electrons of the interstitial atom giving rise to half bonds. Zener'-4 in a recent series of papers has proposed a new theory of ferromagnetism and has developed an explanation of the observed saturation magnetization of iron nitride (Fe,N) using the concept that nitrogen accepts electrons from the 3d-shell of iron. Jack," on the basis of atom size considerations in iron carbonitrides, has proposed that nitrogen transfers or donates electrons to the inner 3d-shell. He found that the effective size of the carbon atom was less than that of nitrogen and thus suggested that the interstitial atoms give up electrons. Kiessling" has studied the borides of several transition metal atoms and proposed that boron loses one p electron to the transition metal. He postulated that the additional electron added to the metal lattice compensates for the loss in metallic properties which results from the increased metal-metal atom separation. GuillaudT3" has proposed similar arguments from some recent magnetic studies he had made on manganese nitride. However, he did not base his conclusions on a quantitative argument. Pauling," in a recent paper, discussed electron transfer in in-termetallic compounds. He classified nitrogen as a hyperelectronic atom which can increase its valence by giving up electrons. He classified the transition metals as buffer atoms which are capable of either accepting or giving UP an electron. He pointed out that two factors are operating which promote electron transfer because they lead to increased stability. The first is an increase in the number of bonds, and the second is a decrease in the electric charges on the atoms. These ideas when applied to the interstitial nitrides would indicate a viewpoint favoring electron transfer by nitrogen to the transition metal. Hagg7s arguments in favor of no exchange are adequately summarized by Wells." Implicitly, Hagg

Jan 1, 1956

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966

[ ]

Jan 12, 1959

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,' from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

JOHN W. BELL,* Montreal, Canada (written discussion?).-Mr. Hardinge's "hammer" theory is, I believe, a sound one; but, unfortunately, at the very place in the Hardinge mill where there should ,be a large number of small "hammers," there is room for only a very few. The results in Mr. Van Winkle's paper seem to indicate that the practical development of the theory can best be accomplished by stage crushing, using cylindrical mills. It would be very interesting to know if any stage-crushing experiments have been made at Inspiration with Marry mills. Mr: H. Kenyon Burch says:1 "The Marcy mill also proved to be a most excellent intermediate crusher, handling as high as 800 tons of 3-in. feed and under, to pass an 8-mesh screen without return of oversize." It seems reasonable to suppose that a large part of this output would be a finished- product; consequently, if it were possible to send the oversize from two of the primary mills to one secondary mill using balls of small diameter, a considerable saving in power might be realized, provided it were not necessary greatly to enlarge the secondary mill. It does not seem reasonable to suppose that fine material can he crushed as quickly or as efficiently in a primary ball-mill as in a re-crushing mill especially designed for that work. Experimental data, of course, are essential in deciding questions of this kind.

Jan 4, 1918

By G. R. Gardner, D. H. Davis

Increasing realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. Classification of Dust Sources The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these—namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By Richard S. McCaffery, Clarence H. Lorig, Joseph F. Oesterle, Ira N. Goff, Oscar O. Fritsche

This paper is the report of an investigation to determine the relations between the viscosity, temperature and composition of that portion of the silica-alumina-lime-magnesia system(l) within which blast-furnace slags are found. The work reported in this paper was made possible by a grant of funds from Engineering Foundation. It is a part of a project, the determination of properties and structure of iron blast-furnace slags, upon which the laboratories of the University of Wisconsin have been at work for some years. Three papers have been published, which have marked the progress of the study of iron blast-furnace slags at Wisconsin. The first,(2) Desul-furizing Power of Iron Blast-furnace Slags, discussed the solubility of sulfur in slags that contained no magnesia and discussed the viscosity. The second, (3) The Constitution of Iron Blast-furnace Slags, developed the constitutions of slags in the four-component system, silica-alumina-lime-magnesia, and pointed out an explanation of slag structure. Composition of Iron Blast-furnace Slags,(l) which was the third paper, gave a method of calculating the percentages of the various compounds present in slags when the amount of oxide was given and also an interpretation of quaternary equilibrium. Illustrations were given of the mineral composition of blast-furnace slags and some applications of composition results were shown. Because of their relative ease of measurement, the viscosity-temperature relation for slags was selected as a factor which would be useful in correlating the physical properties of molten slags to furnace operation. With this in mind the viscosities of slags whose compositions are in that portion of the quaternary system, silica-alumina-lime-magnesia, in which blast-furnace slags occur, were thoroughly investigated.

Jan 1, 1932

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By E. J. Koval

Practical miscible displacement processes will be characterized by lingering of the solvent into the oil. The lingering process is brought on by viscosity differences, and can be accentuated by channeling and longitudinal dispersion. The effects of these factors on the efficiency of unstable completely miscible displacements are combined in what is called the K-factor method. This method, analogous to the Buckley-Leverett method, predicts recovery and solvent cut as a function of pore volumes of solvent injected. Experimental data are included and show excellent agreement with theory for a wide variety of sandstone cores and viscosity ratios. INTRODUCTION Theoretical considerations,1 laboratory experiments,2 and pilot tests3 lead to the conclusion that miscible displacements in the field will be unstable In an unstable miscible displacement, the solvent fingers through the oil. This fingering leads to early breakthrough of the solvent and an extended period during which both oil and solvent are produced. For such a system, there appear to be four principal factors which bring about or accentuate the effects of instability: longitudinal dispersion (including geometrical effects), channeling, viscosity differences and gravity differences. Other factors, such as diffusion and flooding rate, can also influence the effects of instability, but at the flooding rates considered in this report, circa 15 ft/D, they are unimportant. Longitudinal dispersion can be thought of as a spreading of the solvent front caused by the presence of microscopic inhomogeneities. Channeling of the solvent occurs when a porous medium has macroscopic inhomogeneities; i.e., gross permeability variations. Viscosity differences lead to fingering of the less viscous solvent. This difference in viscosity accelerates the growth of fingers along paths previously developed because of permeability variations. Gravity differences lead to overriding by the usually less dense solvent. Al- though gravity effects are generally small at a flooding rate of 15 ft/D, they would, nevertheless, unnecessarily complicate the interpretation of flooding experiments. For this reason, all the experiments reported herein were done with matched density fluids. Fingering and the resultant poor areal sweep were recognized early as the dominant influences on the efficiency and the economics of miscible displacement processes. Much research effort has been spent on ways to minimize fingering and increase areal sweep such as the use of graded viscosity slugs4 or water slugs. Some researchers attempted to work out ways to prevent fingering completely; i.e., to achieve a stable displacement through gravity or latitudinal dispersion stabilization. l Others did not attempt to control fingering but obtained an economic process by merely recycling the solvent and sweeping pattern by pattern.6 During this period, all aspects of fingering came under close scrutiny. Some researchers reported on how fingering looks2 and how it is affected by viscosity ratio,7 geometry,7 and slug size.2,* Peaceman and Rachfordg suggested a mathematical approach to the prediction of unstable miscible displacements in relatively homogeneous sand packs, but their work cannot be extended conveniently to heterogeneous systems. Hence for a heterogeneous system, no method is presently available for predicting solvent cut and recovery as functions of pore volumes of solvent injected. The purpose of this investigation was to attempt to fill in the gap in our knowledge concerning the prediction of performance of unstable miscible dis placements. Necessarily, the system selected for study was a relatively simple one. The restrictions placed on the system were: (1) The system was linear; (2) The solvent was miscible in all proportions with the oil in place; (3) The solvent was continuously injected into the porous medium; (4) Gravitational effects were eliminated by matching densities and (5) All the flood rates were high and constant at 15 ft/D to avoid any small rate effect and to minimize any diffusion effects. To simplify and to indicate that both longitudinal dispersion and channeling arise from permeability variations, the effects which they cause or influence have been termed heterogeneity effects. The use of

By Lars Thomassen, Ernest Kirkendall, Clair Upthegrove

THE amount of research done in the last few years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Desch1 in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for its review and bibliography is an article by A. I. Krynitsky.3 While considerable material has appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined at three temperatures. PROCEDURE The method used consisted of plating copper on a beta brass, heating it to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the temperature at which diffusion takes place the beta brass is saturated with copper. Thus, while the beta brass supplies the zinc, no diffusion takes

Jan 1, 1938