Search Documents

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7'e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,' and Owen has started some detailed studies with a carbonyl system.' A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4'5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By E. C. Truesdale

A FEW years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.2 During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. TABLE 1.-Typical Analyses Percentage by Weight Sum of Zinc Pb, Fe, Pb Fe Cd Al Cd Special High Grades 0.007b 0.005b 0.0056 none 0.0106 C.P. (chemically pure) <0.0002 0.0005° 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 6-37). b Maximum. c Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936

By H. H. Rachford

Numerical solutions of immiscible flow problems in which dispersive effects of capillarity are dominated by convection require excessively fine grid spacing with attendant high computing costs. The use of coarser spacing reduces cost but often produces oscillation or undue dispersion associated with displacement fronts, A numerical formulation is proposed here which should be applicable to two-dimensional flow problems. it is in part analogous to an approach previously tested for miscible systems. The convective transport is approximated using a change of variables to yield a coordinate system moving approximately with the local characteristic velocity. The capillarity-induced dispersive terms in the differential system describing the process are approximated with respect to a fixed coordinate system by the usual implicit formulation. One-dimensional tests of the procedure yielded results in which the saturation profiles tended smoothly to the zero-capillary pressure solution as the ratio of viscous to capillary forces was successively increased in a sequence of calculations. This contrasted favorably with solutions by other numerical procedures which would require attendant grid refinements to approach the zero capillary pressure results. INTRODUCTION Numerical solution of displacement problems has until recently relied on applying methods developed primarily for transient heat-flow problems. Such problems are classified as parabolic in type, and where the heat transport is purely by diffusion their solutions are characterized by a high degree of smoothness. It is not surprising, therefore, that for approximating these solutions available finite difference methods are quite adequate. In flow problems the transport is partly by diffusion, partly by convection or flow. Although the problem remains of parabolic type because the dispersive effects of capillary forces or diffusion play some role in every displacement, at high flow rates the problem is dominated by convection, and solutions tend toward those of equations of the hyperbolic type. Solutions of hyperbolic problems are characterized by the translation of fronts, or discontinuities, that may progressively increase in sharpness. Numerical methods for treating parabolic problems become less and less satisfactory as displacement rates increase and the role of dispersion due to concentration or capillary pressure gradients becomes small relative to transport due to flow. In computation the difficulty manifests itself as an error associated with the grid size chosen. 1-6 In summary, if the heat-flow type approximations are to include the terms arising due to convection, one of several choices may be made: (1) an upstream (to the direction of flow) approximation for the convection terms may be used; (2) a centered-in-distance (CID) approximation may be used; or (3) a recently developed approximation based on the theory of oscillation matrices may be chosen.6 The last appears to have significant promise for one-dimensional flow problems; its extendibility to two or three dimensions is an open question. In either of the first two approaches, a suitably small ratio of v&/D must be maintained, where v is the velocity, & is the grid spacing and D the effective dispersivity in the direction of flow. In the first choice, the approximation of the convective part is only first-order correct and errors introduced appear as a numerically induced dispersivity of magnitude proportional to v?x. In the CID choice, the approximation can be second-order correct, but the difference formulation fails to satisfy the maximum principle unless a condition on v?x/D is met. Practically, this means that for high flow rates oscillatory solutions may result in the neighborhood of a front unless exceedingly small grid intervals are taken. While the procedure proposed by Stone and Brian4 permits a less severe limitation to be placed on this ratio, ultimately the flow rates increase relative to the dispersivity the oscillation obtains. Further, extensions of their approach to higher dimensional systems may be attended by considerable

Jan 1, 1967

By Clarence G. Merritt

Stainless iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mlysterious electrolytic effects or comparatively minute non metallic inclusions. Many uses for a steel with such excellent physical properties as are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties,1-2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties—hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C;, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion. Monypenny reports that a loss of hardness is

Jan 1, 1932

By J. L. Zakin, G. K. Patterson, J. M. Rodriguez

Correlation has been obtained between drag-reducing characteristics for turbulent flow in a pipe and measurable properties of several polymer solutions. Several concentrations of high molecular weight polymethyl methacrylate in toluene, high molecular weight polyisobutylene in both toluene and cyclohexane, medium molecular weight polyisobutylene in cyclohexane and benzene and low molecular weight polystyrene in toluene were studied. Data obtained in these nonpolar solvents and literature data for more polar solvents were successfully correlated as the ratio of measured friction factor to purely viscous friction factor vs the modified Deborah number vrl/D0.2 where 71 is the first-mode relaxation time of the solution estimated by the Zimm theory. A shift factor which is a function of intrinsic viscosity 1/(4[?] - 1) allowed all the data obtained with nonpolar solvents to be correlated as a single function. For these systems, most of the data fit a single curve to within + 5 percent of the average friction factor ratio. The shift factor did not give a unique function of the data for the more polar systems. INTRODUCTION The phenomenon of drag reduction in polymer solutions was first studied by Toms1 in dilute solutions of polymethyl methacrylate in mono-chlorobenzene. The drag ratio for flow through circular tubes has been defined2 as the ratio of the pressure. drop of the solution to the pressure drop of the solvent at the same flow rate. The drag ratio is less than 1.0 for a drag-reducing fluid. Practical use of drag reduction is being made in fracturing operations in the petroleum industry.3 A more fundamental quantity is the friction factor ratio, defined as the ratio of the observed pressure drop to that predicted for a solution of the same viscosity characteristics and density at equal flow rates using the Dodge-Metzner friction factor equation4 Viscous solutions with drag ratios greater than 1.0 can have friction factor ratios less than 1.0. For practical applications, it is drag reduction which is of interest. However, for correlation the fundamental ratio is the friction factor ratio. In recent years, drag reduction has been studied extensively. Recent studies have shown that reasonable predictions of the incipience of drag reduction in polymer solutions can be made from the properties of the solutions and the flow Variables.5 However, it has not been possible to predict accurately the amount of drag reduction to be expected for a given polymer solution without any drag-reducing turbulent flow data on the same solution.6 For flow through circular tubes it is well established that there is a concentration effect and a diameter effect on drag reduction. Toms1 observed that drag reduction increases with an increase in the concentration of the solution up to an optimum concentration beyond which, due to the increased viscosity of the solutions, the drag ratio increased with an increase in concentration. Hershey 7 observed that for dilute Newtonian polymer solutions in nonpolar hydrocarbon solvents, a normal transition region may be obtained followed by a departure from the von Karman equation (on a friction factor-generalized Reynolds number chart). The point of departure is a function of diameter: the smaller tubes depart at the lower Reynolds numbers. Concentrated solutions may show no abrupt transition region, but merely an

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"&apos; as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

By Nicholas J. Grant, Oliver Preston

A series of dilute solid solutions of a1uminum and silicon in copper, in powder -form, were internally oxidized, compacted, and extruded, to produce Cu-A12O3 and Cu-SiO2 alloys with 0.1 to 12 vol pct of oxide. Room-temperature tensile tests, creep-rupture tests from 450oto 850°C. conductivity measurements, and recrys-tallzzation studies were made. Oxide particle size and interparticle spacings were determined in an effort to relate the structure to measured strength values by means of known dispersion strengthening theories. A new dispersion strengthening theory, based on the effect of the dispersed phase on the retention of strain energy from the deformation step, zs proposed for this type of alloy, THE study of dispersion strengthening is of partitular interest in high-temperature materials technology in view of the excellent creep-rupture Properties and thermal stability achieved with SAP.1-5 Considerable effort has been devoted to this study in recent years, and encouraging results have been obtained in a number of systems.6 In general, the most

Jan 1, 1962

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado, The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steep gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike&apos;s Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construction. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937

By R. V. Norris

It was stated in a former paper1 that an intensive study of anthracite costs was being made by the engineers of the United States Fuel Administration. The results of this study are now available and are offered as a supplement to the former paper. Anthracite costs as reported for the 6-months period, December, 1917, to May, 1918, inclusive, as compiled by the Federal Trade Commission, were used as a base, and charts similar to those described in the former paper were made for the standard white ash anthracite and for red ash and Lykens valley coals. Adjustments The adjustments of cost from a reported to a price-fixing basis, as described for the bituminous methods, were applied but showed only minor adjustments as necessary. The great spread in anthracite prices on the varyingsizes, which for the 6-mo. period under review ranged in average from $5.244 for nut to $2.074 for barley coal, makes the question of the percentage of sizes produced at the different collieries a vital one. The realization with the same prices for each size must be within very wide limits, when it is considered that the percentage of prepared coal reported from different collieries varied from over 80 per cent. to below 30 per cent. for fresh-mined coal. Hence, as the spread in prices for the various sizes must be predicated on some percentage, it is essential to find some method of adjustment to allow for this variation. The logical method of adjustment is to calculate actual costs to costs as of the standard percentage of sizes, so that the margin between the adjusted costs and the average realization shall be the actual margin for each colliery between its actual costs and actual realization due to its particular percentage of sizes. As a base for realization the actual percentage of sizes for fresh-mined coal for the 6-mo. period was adopted. This percentage is given in Table 1.

Jan 1, 1920

By Gerald Edmunds, R. K. Waring, E. A. Anderson

Brass is liable to failure under the combined influence of stress, certain corrosion media, and time, a phenomenon commonly termed season cracking or stress-corrosion cracking. The consequences of this are serious in applications of brass generally, including the important field of cartridge cases. Cartridge cases (70 Cu: 30 Zn) that fail from this cause may allow the escape of gas from the gun breech, a hazard to the shooter, and may not eject, thus temporarily putting the gun out of action. In loaded cartridge cases, the stress present is partly residual from the, drawing and necking operations and partly applied by the insertion of the projectile. Ammonia, present as a decomposition product of smokeless powder, air and moisture constitute corrosive media. The prevalence of season cracking has been reduced considerably, but not eliminated, during the past quarter of a century by low-temperature annealing to relieve stresses residual from fabrication, a method suggested by Diegel 38 yr. ago(I).2

Jan 1, 1945

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain&apos; introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?&apos; nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?&apos; are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By J. M. GARZA

The production of oil in Mexico during 1945 was 43,402,852 bbl., or a daily average of 118,912 bbl. In March 1938 most of the oil properties were taken over by the Mexican Government and since then have been operated by Petroleos Mexicanos, an agency of the Government. The variations in the production during the last 8 years have been due to- fluctuations in the export market demand for Mexican oil rather than to the productive capacity of the fields. Since 1937, yearly production, to the nearest hundred thousand barrels, has been as follows :

Jan 1, 1946

By E. W. Johnson, M. L. Hill

The dijfusiuity D was determined at 25° to 780°C- from hyd?-ogen evolution rates. Anomalous evolution from air-melted iron was att~zbztted to residual hydrogen, which is interpreted as a hydrogen compound that decomposes at a strongly temperature-(Ieperzdent rate above 500°C. Above 200°C, D = 0.0014 cm2sec-1 exp (-3200 cal per g atom/RT). Below, 200°C the diffusivity is anomalously low and represented by D = 0.12 cm2sec-l exp (-7820 cal per g atom/RT). It is postulated that at low temperatures the hydrogen in the metal is "trapped" with an energy 4.8 kcaL per g atom below- that of the interstitial hydrogen. 1 HE purpose of the present experimental study was to determine the diffusivity of hydrogen in a-Fe over an extended temperature range. As certain anomalies were encountered, attempts were made to understand the anomalies themselves. This research was in progress both before and after a determination of the diffusivity of hydrogen in nicke1.l The latter system was found to exhibit none of the anomalies of hydrogen in iron, and its description was far simpler. The experiments on nickel also

Jan 1, 1961

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By R. M. Murray

Although blister copper has been produced at the Mount Lyell Mining and Railway Company&apos;s works since 1896, it is only during the past five years that electrolytic refining has been undertaken locally, this having been done previously at customs refineries, at first in the United States, and afterwards at Port Kembla, New South Wales. Left to right: smelter building, converter building, blower building (in which converter-generators are housed), tank house and anode dock. Wire-bar furnace building in background at center. Possessing a hydroelectric power plant capable of generating power considerably in excess of the requirements of its mines and works at the time, the company was in a favorable position to undertake its own refining work, provided this advantage was not offset by the high cost of coal, which would have to be imported from the mainland, and provided also that the capital cost of the plant would not be unduly large in regard to the relatively small amount of copper to be treated. A study of these several conditions led to the adoption of a high-density plant using blister-copper anodes and equipped with an electric boiler to provide any

Jan 1, 1934