Search Documents

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By John L. Burns

The object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-hardening characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classification" is essayed. A.—Relation of Lattice Parameter and Electrical Conductivity to Changes in Physical Properties Due to Aging of Fe-C Alloys Since Whiteleyl in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A, point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,~ and at the same time and independently, W. Koster,~ proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Thomas L. Watson

A part of the field-seasons of 1900, 1901 and 1902 mas devoted by the writer to a study of the manganese ore-deposits of Georgia. A report embodying the results of this study is rapidly nearing completion, and when finished it will be published as a bulletin of the Geological Survey of Georgia. I believe, however, the importance of these deposits warrants a separate and earlier publication than that made possible by the Survey, in which the more important results of the study are briefly set forth. It is principally for this reason that the present paper has been prepared. Previous Work.—Some of the more important deposits of manganese occurring in the Paleozoic area of Georgia were studied to some extent previous to 1890 by Dr. Penrose;t and again in the early nineties by former State Geologist, J. W. Spencer. In a recent paper published in the Transactions, on the " Geological Relations of the Iron-Ores in the Cartersville District, Georgia," Dr. Hayes briefly mentions the manganeseores of the same district. Distribution of the Manganese-Ores.—Georgia is divisible into three geologically-distinct areas which, named in order from southeast to northwest, are (a), the Coastal Plain; (b), the Crys-

Jan 1, 1904

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By J. M. Dahl, R. J. Warrick, O. K. Riegger, H. Van Vlack

A liquid which is rich in oxygen (and silicon) develops at steel rolling temperatures in resulfurized and plain-carbon steels. This liquid fluxes solid manganese sulfide. The composition of the liquid and the resulting microstructures vary with the manganese/silicon/oxygen ratios in the steel. The observations and conclusions zuhich are presented are used 1) to suggest a mechanism for MnS deformation in resulfurized steels, and 2) to rationulize hot-shortness anomalies between plain-carbon and resulfurized steels. 1 HIS is a summary of the dependence of sulfide inclusion microstructures upon steel composition, and an interpretation of the behavior of sulfide inclusions at steel-rolling temperatures. Sulfide inclusions are known to have several metallurgical effects upon steel. Their effects upon hot-shortness are best appreciated. Although hot-shortness is well known, it is questionable whether its mechanism is fully understood because there are several anomalies in our interpretation. For example, why should not high sulfur contents produce extensive hot-shortness in free-machining steels ? A second metallurgical consequence of sulfide inclusions appears because sulfide inclusions improve machinability. Furthermore, globular inclu- sions are to be desired over elongated inclusions. To date, we know that lower silicon contents (< 0.010 pct) favor the globular sulfides, but we do not know why this interrelationship between silicon content and inclusion shape exists. Finally, the evidence is strong that the surface quality of a hot-rolled steel is particularly sensitive to the sulfur content. SUMMARY OF PREVIOUS WORK The role of sulfur in hot-shortness was first suggested during the past century. It is uncertain who was the first to conclude that sulfur was less deleterious in the presence of manganese, and that manganese altered the sulfide phase from a liquid FeS to a solid MnS at steel-rolling temperatures. However, Urban and chipman&apos; emphasized that liquid FeS may accumulate as an interdendritic film during solidification. More recently, Keh and Van lack&apos; showed that the intergranular liquid does not completely surround the metal grains at all rolling temperatures. Rather, a small finite dihedral angle exists when geometric equilibration is attained at

Jan 1, 1962

By Leo F. Reinartz

This is the fourth and final installment of Leo Reinartz&apos; summation of the steelmaking industry over the first one hundred years. ALTHOUGH basic open-hearth steel has been in the limelight for many years, it has had to share some of its glory with two lesser but nevertheless important rivals, one 50 years old and one a rejuvenated process. Electric steel Electric-steel manufacture began in a humble way in the United States in 1906, when the first heat was tapped from a 3-ton Heroult electric furnace at the Halcomb Steel Co., Syracuse, N. Y. During the intervening years, it has completely eliminated the crucible process. For many years electric melting furnaces were located predominantly in relatively small, nonintegrated plants, making all kinds of high-grade alloy steels. Most of these furnaces, with capacities ranging from 5 to 20 tons, had basic bottoms. During and after World War II, many large basic electric furnaces, some up to 200 tons in capacity, were installed in integrated plants to make commodity steels. There were several reasons for building electric furnaces. Capital investment per annual ton of capacity was low and furnaces could be installed quickly. Since these furnaces used mostly scrap iron in the charge, no extra expensive coke- and blast-furnace capacity had to be added. The perfection of the top-charging design, and the development of large transformers and furnaces, made possible tons per hour as high as from modern 350-ton. open-hearth furnaces. Electric furnaces have high availability and repair costs are low. The process is flexible. Alloy and plain carbon steels of high quality can be made. Where power costs are low, the operating cost can

Jan 1, 1961

By H. P. Allen

THE Achotla mill of the Cia. Minera de Pe[n]oles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation Of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1937

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.&apos; Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth&apos;s surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner&apos;s contour map.&apos; The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;&apos; the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.&apos; At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes&apos; describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer&apos;s knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By Carl Davis

A description is given of grinding practice on the Rand and of experiments made to improve that practice. The paper includes a description of the experimental plants and methods and the results obtained. THE first tube-mill on the Rand was put into operation in May, 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell 22 ft. 0 in. diameter 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.1 By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from. 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a final product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; -90 mesh, 69 per cent.; and the slime grading -200 mesh, 2 per cent.; -200 mesh, 98 per cent.

Jan 12, 1924

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year&apos;s activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

By F. W. Gibson

A detailed description of the smelting and refining operations of the Amax-Homestake Lead Toller&apos;s smelter at Buick, Missouri. This is one of two completely new lead smelting and refining operations to go into operation in the United States in over forty years. Incorporated into the operation are the new methods and equipment which have been developed and lend themselves to the particular metallurgy of this plant. The text, as well as the statistical data presented, represent actual current practice after 22 months of operation, and although the metallurgy is considered to be relatively simple, several metallurgical problems unique to Missouri concentrates are discussed.

Jan 1, 1970

By D. Hawington

HEALTH and safety in the mining and allied industries of the United States have unquestionably been progressing, particularly during the past three or four years, even though the progress has been anything but great in some branches of these industries. Statistical data to support this statement are readily available as to safety, but similar health data are unfortunately not available. In coal mining the rate of occurrence of fatal accidents per million tons of coal produced for the ten-year period 1911.20 inclusive was 4.27; this rate was 3.84 in 1930, .3.31 in 1931, 3.36 in 1932, and 2.69 (tentative) in 1933. In metal mining, the-rate of occurrence of fatal and- non-fatal injuries per .thousand 300-day workers (calculated) was 224.36 for- the same ten-year period. This fell slowly until after 1929 when it was 203.14, dropping to 170.78 in 1930, to 142.09 in 1931, to 138.46 in 1932, and to 155.13 in 1933. Here, again,-the real progress began in 1931 though the rate in 1930 was not particularly bad. For the same ten-year period, the rate of those killed and injured: in: quarrying per thousand 300-day workers (calculated)

Jan 1, 1935

By D. S. Choi, D. L. McCain

A method of estimating the chain pillar size required to support the wide working faces of longwall or shortwall coal mining is presented. The pillar size is determined through the use of coal strength, entry geometry, panel width, and overburden pressure. Design analysis is focused on a three-entry development system in the Pittsburgh Seam but can be used for other development plans and other seams by substitution of the proper geometric and strength data.

Jan 1, 1981

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts &apos; law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott&apos; made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.&apos;1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts&apos; technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By W. R. Kube, W. H. Oppelt

Five low-rank coals, including two lignites, a steam-dried lignite, and two subbituminous coals, were carbonized at 940°F, in a bench-scale carbon-ize~ with a nitrogen and hydrogen atmosphere, or both, using pressures from atmospheric to 1000 psig. Coking characteristics were observed, and yields, composition, and distribution of products from thermal degradation were determined. The influence of pressure on yields from coal carbonization, as well as on modification of coke structure, has long been of interest. One of the first attempts at pressure carbonization was that of Capps and Hulett1 who in 1917 investigated the effects of pressure ranging from 1 to 20 atm on yields at 600° C for bituminous and subbituminous coals. High-pressure carbonization has not been used commercially for coke production. More recently, carbonization at relatively high pressure in the presence of catalysts and hydrogen has been proposed for the production of metallurgical-grade coke from low-rank fuels.&apos; Another approach involves carbonization at high pressure in a hydrogen atmosphere to produce heating gas and a solid residue that is gasified with oxygen and steam to produce the hydrogen required for hydro-genation 3-4 or, alternatively, is burned to raise steam. Recently it has been proposed to carbonize coal under pressure, burn the gas in a gas turbine to produce power, and use the solid residue as fuel in a conventional steam-power plant.5 Our primary interest in pressure carbonization stems from an attempt to determine the influence of pressure on the coking characteristics of lignite to design a high-pressure slagging gasifier using oxygen and steam. At atmospheric pressure, North Dakota lignite is generally considered to be non-coking. However, lignite and subbituminous coals have been reported to show increased agglomeration properties in steam, hydrogen, or carbon-dioxide atmospheres at elevated pressures, although no strong coke was formed at pressures up to 3000 psig.6 If lignite would agglomerate seriously under gasification conditions, proper flow of charge through the gasifier could not be maintained without installing a mechanical stirring device or destroying the caking properties of the coal before gasification. Data on the caking properties of lignite or other gasification fuel, as well as on yields of products under conditions simulating the carbonization process in the pregasification zone, were required in the preliminary design stage of the gasifier. No information was available concerning the influence of pressure and type of atmosphere on North Dakota lignite. To provide this basic data, the U. S. Bureau of Mines investigated the effect of pressure and a hydrogen or nitrogen-rich atmosphere on the yield of products and on coke formation in a bench-scale pressure carbon-izer. SCOPE OF INVESTIGATION Five coals were tested at 940°F in nitrogen and hydrogen atmospheres, at pressures from atmospheric to 1000 psig. Yields and composition of solid, liquid, and gaseous products were determined as a function of the process pressure, and attention was given to the physical appearance of the solid residue. Percentage of carbon converted, sulfur retained in char, and thermal balances were calculated. In this paper, primary consideration is given to carbonization in a nitrogen atmosphere and to data concerning the solid phase. The effect of pressure in hydrogen is presented in detail for only one lignite. More complete information on the response of the other coals in a hydrogen atmosphere will be published in a USBM Report of Investigations. DESCRIPTION OF EQUIPMENT Details of the bench-scale pressure carbonizer are given in Fig. 1. The body of the carbonizer was

Jan 1, 1961

By A. J. Phillips, C. G. Grant, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By Douglas R. Piteau, Dennis C. Martin

Instability of rock slopes may occur by failure along pre- existing structural discontinuities, by failure through intact material or by failure along a surface formed partly along discontinuities and partly through intact material. Although certain fundamental failure modes are recognized, the mechanisms of slope failure are varied and complex. Such mechanisms are governed by the engineering geology conditions of the rock mass, which are almost always unique to a particular site. An understanding of failure mechanisms requires a knowledge of the physical, mechanical and strength properties of the intact material and discontinuities which make up the rock mass, as well as the structural geology and hydrogeology. These engineering geology parameters also must be evaluated with respect to the slope geometry to determine failures which are kinematically possible. Only after obtaining a reasonable appreciation of the possible failure modes can a rational mechanical stability analysis be carried out. Both two-dimensional and three-dimensional failure mechanisms should be considered in assessing the design of rock slopes. Simple analyses methods are used initially to identify those possible failures which could control slope stability. More complex and detailed analyses usually are required for a few critical failure modes which could control stability, or where a more complex type of failure mechanism is envisaged. Complex failure mechanisms are usually identified when assessing previous slope failures. More detailed information concerning slope geometry and engineering geology parameters must be acquired where analyses must be more rigorous.

Jan 1, 1983

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940