Search Documents

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By Thomas J. Crocker, Galen G. Waddell, Eugene H. Skinner

This paper describes a method of measuring initial and long-term deformations which occur in the medium surrounding mine accessways, and discusses the importance of this type of measurement in assessing support-problem areas. Delineated are (1) description of the rock-deformation monitoring equipment, (2) results of two field tests which monitored rock deformation around 4-foot-diameter raise bores, and (3) a numerical-analysis (finite-element) technique to correlate theoretical with experimental results. Instrumentation developed provided the sensitivity and resolution needed to measure rock deformation around a full-scale raise bore during excavation. Results of the tests conducted at the Lucky Friday mine, Mullan, Idaho, show the relationships between (a) de- formation vs. time, and (b) deformation vs. bit progress. Based on theoretical evaluation of the initial deformation, the medium appeared to behave elastically. Using an estimated field stress of 5,500 psi and Poisson's ratio of 0.20, the gross modulus of elasticity of the rock was calculated to range from 3.15 to 6.0 x 106 psi (with one outlier which was determined to be >12 x l06 psi).

Jan 1, 1971

By William L. Saunders

Many members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-coxpressors and machinery driven by compressed air, has no desire to injure its own business by claiming for this new machine that it should immediately supersede all existing applications of pneumatic transmission of power for drilling. On the

Jan 1, 1908

By W. G. Fischer

Basic laboratory tests on trona and the surrounding shales initiated the Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strength, Mohr's envelope, the biaxial stresses at failure, and creep were investigated. A series of underground problems were then approached using this information and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line were studied. After about 30 stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investi- gate a possible application of warning devices near the cave line. A study of mine reorientation was made. Problems related to the shape and size of pillars and barriers were studied. The effectiveness of roof bolting patterns was examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program. Without this system, mining in more than one instance would have been next to impossible. Indeed, from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars. The Westvaco trona* mine is located near the town of Green River in the southwestern corner of Wyoming. It is owned and operated by FMC Corp. on land leased from the US Government, the State of Wyoming, and the Union Pacific Railroad. A conventional room and pillar system is being used, (Fig. 1) with complete removal of the pillars during final mining. Return air bleeders surround

Jan 1, 1964

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

By Richard I. Petritz

A brief review of today's processing of integvated circuits is given. The major trends in the development of advanced integvated electronics are identified as 1) the broadening of the integvated circuit concept to a large class of circuit function, 2) the processing of more complex circuits within relatively small chips of silicon, and 3) the processing of very large electronic functions on complete slices of silicon. This latter trend, called array technology, is then developed in detail. Emphasis is given to defining the key tech-nological problems. Current progress being made is illustrated. THIS paper will endeavor to identify the major trends in advanced integrated electronics technology. One of these, array technology, will be developed in some detail. The array technology discussion will identify the key problem areas. Since it is the scope of the entire meeting' to present specific progress in the science and technology of integrated electronics, we shall indicate general directions being explored rather than discuss comprehensively solutions to the problems. In order to set the stage for the discussion of future trends in integrated-electronics technology, let us briefly compare the processes by which circuits are fabricated through discrete-device technology with that of integrated circuits technology. The reader is referred to the December 1964 issue of Proceedings of IEEE2 for a comprehensive review of integrated electronics. The article3 by Jay Lathrop is an excellent discussion of integrated-circuits technology. A discussion of the history of semiconductor technology is contained in Ref. 4. A) Current Status of Integrated Electronics. Fig. 1 (top) shows the process by which circuits are constructed from discrete devices. Key points are: 1) Slices containing large numbers of transistors or diodes are processed separately. 2) The slices are scribed into small chips (on the order of 15 mils on a side is about as small as can be conveniently handled) each chip containing one transistor. 3) Each device is specified separately—circuit -function specs are derived largely from device specs. 4) Circuits are formed by connecting together the discrete devices. 5) The number of circuit connections required is approximately equal to the number of devices. 6) There are potentially many more discrete devices per inch2 of semiconductor—only our lack of ability to handle them in discrete form prevents us from going to several orders of magnitude higher density iin Fig. 1, 400,000 transistors are discussed at 1.5 mils on a side). The bottom part of Fig. 1 illustrates the integrated circuit process. Key points are: 1) On the same slice of silicon, transistors, diodes, and resistors are processed grouped to do a complete circuit function. 2) While still in slice form, the components are interconnected into circuit functions by an evaporation process, eliminating the need for separate interconnection steps later. Dramatic improvements in cost and reliability are realized. With a simple flash of metalization thousands of interconnections are reliably made. 3) The slices are scribed into chips which contain complete circuit functions. 4) The circuit functions are specified-not each component in the circuit. This important point was missed by some of the early opponents to integrated circuitry. They argued that, with device yields at x pct, integrated circuit yields would be pct, where n is the required number of devices to make a circuit. This argument leads to extremely low yields for integrated circuits. The fallacy of the argument is that in integrated circuits each device is not specified separately. Furthermore, since a device is forever integrated into a specific circuit function, it need meet only the requirements for that particular function. Discrete devices, on the other hand, are tightly specified so that they can be applied to a variety of circuit functions. 5) Extremely high packing densities are achievable because one need only make the basic devices as large as the circuit demands. Their size is not dictated by handling requirements. A current example

Jan 1, 1967

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By Frederick L. Knouse

THE south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19° to 21° and 30" south latitude; and from 40° to 41° and 30" west longitude. This includes the central part of Espirito Santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Martines, Espirito Santo (Fig. 1). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through Vitoria; and by the E. F. Minas-Vitoria and E. F. Central do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatites, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. EARLY OPERATIONS Mining of quartz crystal in this region began in 1928, and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crystal as small as 10 grams. Since 1941 only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of loo grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, or Domingos Martines, Espirito Santo. Marketable quartz crystal was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large cores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. PRODUCTION The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1946

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neu-mann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempts to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2. was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form 12111. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

Jan 1, 1928

THE. extraordinary volume of work done in this period, and the multiplicity of subject matter, make a year-by-year historical account undesirable, if the account is not to be an assembly of unrelated fragments. We shall, instead, undertake to narrate the development in this period of each of the branches of the subject separately, hoping that their interrelations will be self-evident. There is a certain arbitrariness in the selection of subject matter in the following sections. The development of important engineering alloys-for example, high-speed steel-is disregarded, for it is the primary purpose of this account to relate the advances in ideas, the growth of the science of metals; other historical accounts relate these parallel advances. Nor are advances in techniques stressed, though occasionally the most important are noted; nor is the progress described in allied fields such as welding, cutting, etc.; for though these developments have very frequently made possible the advances herein related, they are far too numerous to recount in anything short of a ponderous volume. There is a more serious arbitrariness, however; it is not an easy matter to draw the boundaries of physical metallurgy, and some contiguous subjects have been omitted that perhaps should have been included, such as, for example, corrosion, gases in metals, the magnetic behavior of metals and alloys, and certain other fields in the physics of metals. REACTIONS IN ALLOYS--DIFFUSION Many of the reactions occurring in alloys proceed by the operation of the process of diffusion in the solid state: the annealing of mixed powders to form alloys, the homogenization of castings or forgings, the freezing of alloys, the treatment of clad metals, the loss

Jan 1, 1948

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By J. P. Pritchard, J. T. Pierce, O. G. Slay

This paper discusses the results of a technology-evaluation program to ascertain the feasibility of a piotornask-photoresist technology developed for fabrication of multiple-layer thin-film superconductive circuitry. The uehicle selected for this evaluation was a 120-bil associative data processor requiring a set of nine photomasks to define a similar number of patterned material layers of lead, tin, and polymer insulation. A total circuit area of 4 sq in. involved 2500 actitle and 12,000 passive crossings. Several short-free, electrically continuous specimens were satisfactorily completed under this program. Problems encountered in the preparation and use of the requi-ed set of Photomasks are discussed, as also are the problets of providing suitable external connections. A major retarding factor in the development of the superconducting thin-film cryotron technology for many years was the absence of batch fabrication means yielding necessary device density and count per substrate for practical applications. Early workers in the field desired only limited numbers of devices to permit careful study of discrete devices and representative circuitry integrating logic and memory capabilities. For these purposes mask stencils could be formed to selectively control the placement of materials, sequentially vapor-deposited in vacuum, to form the multilayer structure. In general a distinct pattern was required for each material layer; therefore, mechanical provisions were required to change not only the material source, but the patterning mask as well, before each deposition. All deposition steps were preferably performed in a single evacuation of the deposition chamber. Thus the means for storing, transporting, and registering masks and sources with respect to the substrate existed and were operated within the vacuum environment. In the authors' experience, the approach was and remains serviceable for preliminary device study, but was not extensible to an economical manufacturing method by virtue of the difficulties inherent in mask stencil preparation and use, and the capital investment implicit in the mechanization requirements. Since the commercial attraction of the cryotron technology stems principally from its potential for economical batch fabrication, the authors' program has placed major emphasis on fabrication methods. A highly useful method has evolved through adaptation

Jan 1, 1967

By Walter Nummela

INTRODUCTION By the end of 1979 pellet productive capacity from the processing of low grade iron ores in the Lake Superior-District will total 86 million tons per year. Of that tonnage, 72 million result from the processing of magnetic ores such as taconite, about 6 million tons from the flotation processing of relatively coarse grained specular hematite, and 8 million tons from the processing of fine grained non- magnetic ores at Tilden. The Tilden flowsheet represents a break- through in the processing of this type of crude ore and hence is unique in the Lake Superior District (1). Operations at Tilden started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleve- land-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling- Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Other companies have conducted extensive pilot plant tests or are in commercial production in the processing of fine grained non-magnetic ore materials (2). Flowsheets and reagent schedules may be different for each particular application, but some of the problem areas in the processing of Tilden ores have also been experienced at operations such as the IOC Plant at Sept-Isles, at Lamco and at Bong in Liberia, and in pilot testing of Fabrica ores of Ferteco Mineracao in Brazil. With a grind of about 80-85% -500 mesh resulting in 50% of the particles in the concentrate being less than 15 microns, a discussion of the pro- cessing of Tilden type ores fits the topic of this workshop. There are very large tonnages of fine grained non-magnetic crude ores which exist throughout the Lake Superior District and other iron ore producing regions. These fine grained non-magnetic materials constitute an important source of iron minerals. Before going into specifics of the flowsheet, it is important to

Jan 1, 1979

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

By L. F. Mondolfo, B. E. Sundquist

The undercooling associated with the nucleation of the secondary phase from the liquid by the solid primary phase was studied in sixty binary alloys by means of a hot-stage microscope. It was found that in a system of a and ß, a usually nucleates ß at low undercoolings, but ß does not nucleate a, except possibly at undercoolings approaching homogeneous nucleation. This behavior can be explained in terms of relative interfacial energies and shows that crystallographic disregistry is only a minor factor in heterogeneous nucleation from metallic liquids. PREVIOUS experimental work1-6 on nucleation of solids from liquids has shown that normally nucleation is heterogeneous, and that small solid particles present in the liquid are responsible for the nucleation. These experiments and the theory that has evolved from them have made apparent that there is a "characteristic undercooling" associated with the nucleation of the solid from a given liquid by a given impurity. Little is known, however, about the chemical and structural relationships between the nucleating agent and nucleated solid that control the effectiveness of the nucleating agent in catalyzing the nucleation, as measured by the required undercooling. A review of the literature has yielded seventeen undercoolingsL-6 for the nucleation of solid from liquid metals by "known" nucleating agents. All values come from experiments in which the metal studied was divided into a number of particles (10 to 300 pin diam.) much larger than the number of extraneous impurity particles so as to obtain a large number of particles free of foreign nucleating catalysts. Known nucleating agents are then introduced by coating the droplets with particles or a thin film of the catalyst. Six of the seventeen undercooling values referred to cases where, for various reasons, the identity of the nucleating species was not at all certain. Another six cases involved nucleating agents with a crystal structure that was not known. Four other cases involved undercoolings listed as greater than or equal to undercoolings which were very likely those for homogeneous nucleation. One investigation3 involved adding to droplets powdered oxides, carbides, and so forth that were doubtlessly covered with adsorbed oxide or nitride films. The highly variable nature of these films resulted in highly variable undercooling (as was also found in preliminary work in this investigation). It is apparent that the information on heterogeneous nucleation in liquid metals is too limited to give rise to any definite conclusions on the nature of the catalytic process. With these problems in mind a new method was

Jan 1, 1962

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947