Search Documents

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By E. W. Davis

THE large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent by mixing ores of various grades, some assaying 4 per cent silica and some as high as 18 per cent silica. For each ton of 4 per cent silica ore mined, a ton of 14 per cent silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large cluantities of ore too lean to be used alone. and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind.

Jan 1, 1930

By Fleming, R. C.

ONE OF THE NEWEST developments of industry rising from the commercial application of scientific knowledge is in the making of solid carbon dioxide from the gas about 1925 the first efforts were made to manufacture "dry ice" on a large scale and at a price to permit widespread use. From that beginning the industry has grown to a consumption of 40,000 tons in 1930. Carbon-dioxide ice, as the name implies, is merely the gas compressed and cooled to a solid. The ice has a temperature of 109° F. below zero and is in many ways superior to water ice. It evaporates to a gaseous form so it is not wet and leaves no trace; in fact, one suggested minor use is as coasters under water glasses on the dining table. The gas is harmless except in large concentrations and. when the ice is used as a refrigerant, the resulting gas actually becomes a preservative, keeping oxygen away from perishable products. Not only does the ice have a greater amount of cold in a small volume than water ice but cooling is effected by direct contact of the resulting gas with the materials to be refrigerated rather than by convection air currents.

Jan 1, 1932

By Harrison Souder

UNDER the stimulus of steadily in- creasing 'demands of the steel industry at home, and with the supply of available ores from abroad appreciably diminished owing to vigorous rearmament campaigns in Europe, production of Eastern magnetite ores reached an all- time peak in 1937. Although the figures given in the accompanying table are partly estimated (actual figures were available for eleven months only), it appears that 1937 production was nearly 47 per cent higher than that of 1936.

Jan 1, 1938

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By E. W. Shilling Harwick Johnson

The separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordeyl. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Probably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines5"7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made? and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type. Specular hematite is usually considered nonmagnetic; that is, it is very feebly magnetic as compared to some other minerals. If specular hematite is placed in a steady magnetic field there is no apparent attraction. At the moment of closing the switch, however, some particles may be seen to move. If the field is alternating, the particles are con-

Jan 1, 1936

By E. W. Shilling Harwick Johnson

The separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordeyl. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Probably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines5"7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made? and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type. Specular hematite is usually considered nonmagnetic; that is, it is very feebly magnetic as compared to some other minerals. If specular hematite is placed in a steady magnetic field there is no apparent attraction. At the moment of closing the switch, however, some particles may be seen to move. If the field is alternating, the particles are con-

Jan 1, 1936

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By H. M. Roche

IN the first section of- this article, published- Feb. 4, the author reviewed the his¬tory of iron ore mining in New Jersey, listed the reserves and possible markets of this ore, and discussed the role of Lake Superior and foreign ores in domestic steel production. This concluding section of the article emphasizes the metal¬lurgical value, future markets and mining coats of Jersey ores. Mr. Roche's thesis is that industry can profit both metallurgically and econom¬ically through a greater use of Jersey ores --that these orebodies are as yet prac¬tically unexploited, and con¬stitute a valuable national re¬serve fully worthy of careful consideration by Mid-West¬ern steel makers.

Jan 1, 1937

By Evan Evans

IT is appropriate to evaluate 1947 in review as a year of a peacetime record production of about 676,000,000 tons of coal (anthracite and bituminous), closely approaching the extraordinary wartime output in 1944. Considering the general price-wage inflation, it is in point to note that the coal industry sustained the highest wages paid to workers in any major industry, but that coal prices at wholesale levels have risen much less percentage wise than the average for all commodities. The sellers' market continues to prevail. In addition to serving our own country's enormous needs, our coal industry is exporting extraordinary tonnages overseas. This unusual export demand is likely to continue for a while. Moreover, the demand in Europe for American coal mining machinery is a real tribute to the management efficiency of our modern mechanized coal industry. Competitively, the petroleum industry is concerned over its long-term supply, and already a synthetic fuels industry is being publicly advocated. In due time coal and lignite are bound to be

Jan 1, 1948

By Earl Oliver

SEVERAL notable papers, and free discussion on many controversial subjects, marked the various sessions of the Petroleum Division at the annual meeting. The Division first convened on Tuesday afternoon, Feb. 16, and wound up with a dinner and technical meeting on Thursday night. H. C. Fowler presided at the opening session, which was devoted to problems of engineering research and production engineering. Joseph Chalmers abstracted his paper on the flow of air and gas through porous media, in the preparation of which E. L Rawlins and D. B. Talia-ferro contributed. G. H. Fancher told how much he and his associates at Pennsylvania State College were interested in this field, and described the problems they had met in conducting test work. He made a plea for standardization of testing methods. Mr. Fowler then read an abstract of written discussion by Professor Barb, which was followed by discussion by Dr. Fancher and Mr. Chalmers of technical points in connection with the Chalmers' paper. H. H. Hill abstracted written discussion from Messrs. Wilde and Moore, of the Humble company. The second paper, by K. B. Nowels, on computing pressure drop in the pipe of flowing oil wells, was abstracted by the author. Messrs. Blair Smith, G. W. Coggeshall, and I. I. Gardescu participated in the discussion, and the chairman abstracted written discussion prepared by Mr. Rawlins. Most of this had to do with the viscosity of gas¬oil mixtures, on which subject Mr. Nowels said there was great need of accurate technical information.

Jan 1, 1932

By Ben-Zion Weiss, Melvin R. Meyerson

Chromium diffusion coatings on commercial Armco iron lead to carbide precipitation at the grain boundaries in and below the coatings. High compressive stresses are introduced into the coating and, as a result, tensile stresses are introduced into the base material below the coating. In coated samples, fatigue cracks form at the grain boundaries below the coating after only a limited portion of the total lifetime (5 to 10 pct). Residual tensile stresses and a stress concentration caused by precipitated carbides seems to be responsible for early crack nucleation. Stage I of Propagation may be divided into two substages: I-a in which the crack Propagates along grain boundaries, and I-b in which the crack propagates along slip boundaries according to a shear mode. In uncoated samples, the cracks form at slip bands after 40 to 50 pct of the total lifetime. In coated samples the Propagation process takes longer than in uncoated samples because of the moderate rate of crack extension until the crack breaks through the coating. The chromium-diffusion coating causes little if any increase in fatigue life. CHROMIUM diffusion is one of the most popular processes used to apply coatings to iron alloys. This popularity stems from the fact that the diffusion treatment is comparatively easy to carry out, and it improves certain surface properties such as corrosion and wear resistance as well as some other properties. Very little effort has been devoted to the investigation of the effect of chromium-diffusion coatings on mechanical properties and particularly on fatigue properties. Since the chromium coating usually represents a small fraction of the total volume of the base material it is generally assumed that the macro properties are dependent principally on the base material rather than the coating. Insofar as fatigue is concerned, there are indications that the fatigue life of the chromium coating is not less than that of the basic material and the fatigue properties are generally not reduced by it.' But chromium diffusion causes drastic structural and chemical changes in the region of the material surface2-4 which introduce additional residual stresses. Such changes must affect fatigue crack nucleation and may sometimes affect the initial stages of propagation. Furthermore, it is conceivable that the secondary stages of the crack propagation could be influenced by some irreversible structural changes in the core of the material, which stem from the long-time heat treatment at high temperatures required to apply the coating. This paper analyses the structural and compositional changes produced in commercial Armco iron by a chromium-diffusion coating and the effect of the coating on fatigue crack initiation and propagation. EXPERIMENTAL PROCEDURES The investigations were carried out with commercial Armco iron. The chemical composition of the iron, the number of specimens tested, the grain size produced during chromizing and heat treating, and the thickness and microhardness of the chromized layers are shown in Table I. Samples were chromized by a gas diffusion process. The temperature and time of the diffusion coating process were chosen according to a previous grain growth study. It had been found that at a temperature of 970°C and a holding time of between 3 and 9 hr there are practically no changes in grain size. To describe the grain size more accurately the ASTM method5 was supplemented by a statistical analysis of the mean volume diameter as outlined by Fullman6 and The The mean volume diameter was deter- mined from D = p/2m where D is the mean volume diameter, and m is the mean reciprocal value of grain diameters as seen on the micrograph. The shape and the size of the asymmetrical sample, see Fig. 1, were chosen so as to facilitate the study of fatigue crack initiation. Before coating, the samples were machined and the surface of the groove was polished. After chromizing, the two side surfaces were machined and polished so as to retain the coating only on the top surface of the groove. Residual stress in the chromized layer was measured on the top of the grooved section of the specimen after the diffusion process. The inclined incident X-ray beam procedure was used.9'10 The computations were performed with the initial assumption of a zero surface normal stress component. An electron microprobe analyzer was used to obtain the relative amounts of chromium and iron con-

Jan 1, 1970

By Joseph Domenico

AMONG others, one of the most important duties of the accounting department is to disclose to the management the cost of production accurately and as quickly as possible after the ore has been produced and treated. A report is issued daily showing man shifts and the cost of labor, supplies, power, and miscellaneous charges to each department of the operation: mining, crushing, milling, packing and loading, and general expense. Mining costs are broken down into stoping, handling, development, exploration, and miscellaneous, and each of these subdepartmental costs are further broken down into the branches making up the subdepartment. Costs of crushing, milling, packing and loading, and general expense are detailed in the same manner. With such a detailed daily report as this, the management is able to keep in close touch with the efficiency of the entire operation. Because no expense items are deferred or spread over a period, and so that the report does not lose its comparative valve, appearances of unusual charges are explained.

Jan 1, 1946

By P. H. Mell

CAN the auriferous slate deposits of the Southern mining region ever be successfully worked? is a question that has been often asked me by persons seeking investments in Southern mines. As the subject is one that has given me much thought during the past few years, I have decided to present my conclusions to the members of the Institute for their consideration. Those who have had the opportunity of exploring the region mentioned above, will readily recall to mind numerous localities, to which their attention was directed by would-be miners, as "rich and desirable properties," in which there were but few quartz seams running in every direction through fine-grained talcose slate. Most of the gold in sued formations was always found disseminated through the slate, and but a small percentage contained in the quartz. Such are the deposits I propose to discuss in this paper. Of course there are many excellent quartz mines in the South that are paying the owners good profits, and many more to my knowledge, that are not being worked for obvious reasons. But it is out of the question to suppose that these slate deposits can be practically

Jan 1, 1881

By Edwin Ludlow

T HE OPEN FORUM on this subject called by Mr. Hoover at the recent meeting of the Institute' brought out a large number of very able papers, and a very full discussion of all the problems involved. The criticisms of the bituminous industry were: 1. That it was over-developed with the possible output nearly 50 per cent. in excess of the present requirements; that during the summer there were plenty of cars and no orders, and during the winter there were plenty of orders but no cars. 2. That the mines were not properly developed from an engineering standpoint, and that the recovery of the coal varies from 50 per cent. to 95 per cent. 3. That this industry, employing over 600,000 men, could, if running full time, release 100,000 men for other work. 4. That the studies made by the engineers of the Fuel Administration showed that the cost of production increased with a loss of time and that with a 50 per cent. operation the increase in cost was about 40 per cent.

Jan 1, 1920

By W. R. Ingalls

The manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been done chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the re-verberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood, and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Con City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose. Just as zinc may be burned off in a blast furnace, so also may it be done in a reverberatory. Indeed, there is less trouble, in some respects, in a reverberatory, for therewith there is no shaft in which accretions may

Jan 1, 1918

By D. O. LIVINGTON

(Presented by invitation at a meeting of the Spokane Local Section of the institute, Feb. 17, 1912.) THE Pilares de Nacozari mine is located in Sonora, 75 miles south of Douglas, Ariz. The town of Douglas is on the International Boundary and is the place at which the ores from the Bisbee mines are smelted. The Moctezuma Copper Co. owns the mines at Nacozari, and the copper-concentrates shipped to the Copper Queen smelter, at Douglas, make a good smelting-mixture with the Bisbee ores. The Moctezuma Copper Co. and the Copper Queen smelter at Douglas, as well as the railroad from Douglas to Nacozari, are owned by the Phelps Dodge Co. The ore-deposit occurs in the form of a large ellipse with a major axis of approximately 2,000 ft. and a minor axis of about 600 ft., the major axis bearing about 90 W. of N. The whole of this ellipse is more or less mineralized; the surface being principally an iron gossan with some occasional copper-stains. Below the oxidized zone, which is not more than 50 ft. deep, the minerals are pyrite and chalcopyrite, with occasional seams of chalcocite, the latter being rare. There appears to be no well-marked zone of secondary enrichment, the oxidized gossan over the greater part of the deposit changing suddenly to what is apparently the original unaltered ore. The copper-values are concentrated around the perimeter of the ellipse, and it is principally around this perimeter that the mining is done. The ore mined averages a little more than 3 per cent. of copper, with a small amount of silver, less than an ounce per ton. Some ore of considerably higher grade than this has been shipped, however, but the above average is of the mill-run. The ore is wider near the two ends of the ellipse than along the sides, and is mined in some cases to a width exceeding 200 ft. The country-rock for the first vertical 500 ft is a volcanic acid breccia, probably rhyolitic; below

Sep 1, 1912

By Thomas T. Read

THE benefits derived from stabilization of industry that might possibly be attained through some scheme of centralized economic planning have been much discussed of recent months, and opinions on the subject range from those who believe that some agency like the War Industries Board would be practicable to create and wholly beneficial in effects, to those who are equally convinced that none of the suggestions so far advanced are at all practicable, or likely to be productive of more of good than of evil. The discussion has been on the general topic, but-many of those who have written or spoken on it have introduced economic problems of the pinera1 industry; for example, Newton D. Baker, who referred to the coal industry in his address on economic planning at the Williamstown Institute of Politics on July 31, and then went on to say, "Industrial progress is made by the development of new things, but new things upset the equilibrium of any plan. Who could have planned the industrial effects of the development of the railroads, or the economic changes which you have seen attend the development of the internal combustion engine. Obviously, unless we are prepared to put world economics in a strait-jacket and, like the encyclopedists, write its full history on the theory that further progress is impossible, no such plan could be made for nations which are forging ahead as is entirely rational for nations which are still catching up."

Jan 1, 1931

By Stuart H. Ingram

DEFINITION THE term lightweight aggregate implies material which may be substituted for the usual rock, sand and gravel commonly used as the major part of concrete, but distinguished by being much lighter in weight. BACKGROUND The art of making and using concrete is old and well developed. Research and experience have pretty well determined the qualities necessary in its constituents, and time has tested theories and applications. Elaborate specifications and tests have been devised and generally adopted governing all phases of concrete work, from selection of material, through engineering design and down to mixing and placing. Standard practices have become routine to executives and laborers, and operations have been simplified and costs lowered. Though many lightweight aggregates meet the basic specifications necessary for usefulness, their physical qualities are so different that they frequently will not pass standard tests, and some of them cannot be mixed and placed with the usual formulas for water and slump. As a rule their use produces a concrete with a lower modulus of elasticity which requires design change, and being produced in much smaller quantities than ordinary aggregate, production costs are higher. This latter works in a vicious circle to restrict their use and maintain prices that are not competitive, except as against each other. INCREASED DEMAND In spite of such handicaps consumption has grown steadily for the past two decades and is apparently growing even faster today. It is evident that lightweight concrete must have better qualities, and be sufficiently better to overcome the higher cost and the other difficulties and disadvantages pertinent to the use of a new and different material in an old industry. Hence the study of its main ingredient should be of interest to all engineers. Our group has a double interest in the subject since most of the materials which have been used as sources of lightweight aggregate are either mined, or are by-products of mining operations. We are directly interested in their production as well as their use, and since available supplies of materials suitable are limited, the increasing use, and rising demand, make the discovery of new sources, or the development of processes to adapt other natural materials to this use, a promising field; and one in which our profession should take an active part. RECENT DEVELOPMENT Descriptions of ancient work contain references to the use of spalls of tuffs or pumice in concrete masonry, but it is only since the nineteen twenties that serious attempts have been made to produce and market lightweight aggregates. A period of rapid advance in theory and practice in cements, mortars and con-

Jan 1, 1947

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982