Search Documents

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By B. E. Warren

Jan 1, 1965

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By Helmut Thielsch

In recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsifi-cation and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.' In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously. From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time—i.e., improving the plant efficiency— great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. Apparatus The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2½ in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1947

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

Jan 1, 1967

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By F. Weinberg, L. MacAulay

DAVIS,' in an investigation of solute redistribution along molten rods of dilute silver in tin, concluded that at horizontal temperature gradients below approximately 5°C per cm very little convective mixing takes place. Cole and winegard2 observed temperature oscillations in horizontal melts of tin, with temperature gradients of several deg per cm. They associated the temperature oscillations with the presence of convective flow in the melt. At temperature gradients less than 1°C per cm they did not detect convective flow. In the present work, direct measurements of con-vective flow in liquid tin have been made using a radioactive tracer technique. The results indicate that extensive convective flow occurs at temperature gradients below those previously reported. The apparatus used to determine the extent of con-vective flow is shown in Fig. 1. The graphite boat Fig. l(a), has two rectangular channels both of which contain molten tin. Radioactive Ag110 in the form of Sn-0.2 pct Ag alloy was introduced at the end of one channel, by rotating the cylinder shown. A series of fixed thermocouples were positioned along the center of the second channel to determine the temperature gradient. It was assumed that the two channels had identical temperature distributions. The graphite boat was inserted into a vycor tube which was surrounded by a multiple winding tube furnace as shown in Fig. l(b). The tin was melted in an argon atmosphere. The distribution of Ag110, as a function of position along the boat at a given time after introduction of the ~g"', was determined with the

Jan 1, 1970

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By Thomas Leonard Watson

Jan 1, 1906

By R. K. Agarwal

In this paper, a new technique developed to analyze two-dimensional nonhomogeneous models is described. A simple three-layered medium with a circular hole centrally located in the intermediate layer is considered. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of the intermediate layer and the hole diameter. A comparison of stress distribution and procedures for preparation and testing of the model are given. The potential of the technique is outlined. In the process of applying the techniques of stress analysis to problems of rock mechanics, the recent discernible trend has been to postulate highly idealized models of physical situations. As new techniques have been developed, more complicated models have been conceived to simulate mote accurately the physical environment to which the analysis results are eventually applied. In this investigation, a new technique is developed to analyze two-dimensional nonhomogeneous models. The technique is used to determine the stress concentration around a circular hole in a soft material overlain and underlain by a hard material. In mining practice, such situations arise commonly in coal deposits and frequently in bedded or vein-type metallic mineral deposits. DEFINITION OF THE PROBLEM A plate, consisting of three layers with a circular hole in the intermediate layer, is loaded uniaxially, Fig. 1. The variable in the experimental investigation is the height of the intermediate layer, H. The diameter of the hole, D, is kept constant. The stress concentration factors around the periphery of the hole, for various values of H/D, are evaluated using the technique of photoelasticity, Table I. TECHNIQUE OF EXPLORATION Photoelastic analyses of composite models have hitherto been limited to the study of lap and butt joints between glued metals and dissimilar materials.1-3 In mining, Haber and Oudenhoven used composite models to study the stress distribution around a circular hole in two-layered media and the behavior of elastic liners in shallow underground openings.4-5 They used the stress freezing technique devised by Dally et a1.6 The procedure used in this investigation is outlined below: Casting of Layer A: Flat sheets of plastic were cast in a silicon-coated mold using Araldite 502 with hardener 951 in the ratio of 100:8 by weight. After

Jan 1, 1969

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965