Search Documents

By J. C. Bayles

Jan 1, 1885

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By Franklin H. Sharp, Kenneth L. Clifford

During the last few years the New Lead Belt of Southeastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, MG. for about 35 miles. The ore occurs as replacement deposits in the Bonneterre lime- stone formation which is about 1000 ft below the surface. In most of the mines, enough water is produced to supply the milling requirements without any reuse. There are dry areas, however, and at least two mills must rely on water reclaimed from their tailings lake to augment the mine water. These mills have no choice but to utilize recycled mill water.

Jan 7, 1973

By John Johnston

ONLY two of the Institute's 26 Local Sections were unrepresented at the delegates' three sessions, held on Monday morning and afternoon and Thursday afternoon of the annual meeting. The Philadelphia and Wyoming Sections alone sent no delegates. In all, seven hours were spent most profitably in reviewing the work done by the Institute at headquarters and in the field, comparing ideas and practices in varied activities, and in establishing personal contacts. Cordiality and the co¬operative spirit marked the meeting and apparently no one had any serious grievances to air. Four motions were introduced and unanimously passed. The first, which was introduced by B. L. Sackett, was a recommendation by the delegates that a national committee be appointed to cooperate with Local Sections in the matter of student activities, to promote Institute welfare. It was agreed that this recommendation be made simultaneously to the Board of Directors and to the Mineral Industry Education Division. A subsequent resolution by A. M. Smith was passed asking that a part of the duties of this committee be to secure the opinions of Local Sections as to the most desirable methods of interesting students in the preparation of technical papers, by giving prizes or otherwise, and to report their findings at the Section Delegates' meeting next year.

Jan 1, 1933

By Arthur Mackwell

The role of the precious metals is changing rapidly. They are becoming primarily materials of modern industry, and their decorative and monetary functions are diminishing in relative importance. Certainly gold is still the premier metal for jewelry, as silver is for silverware. But these uses are not growing nearly so fast as are the uses of these metals in a variety of industries. This is even more true of the platinum metals. Moreover, this is true despite the fact that the precious metals are highly expensive and liable to substitution by the base metals in cases where this is feasible. For the fact is that the physical and chemical properties of the precious metals make them relatively invulnerable to substitution; where they can be replaced by the base metals, they have been, and the opportunity for further substitution is, therefore, limited. SILVER In November 1969 the United States Treasury stopped minting the only remaining coin with any silver content. That was the silver-clad Kennedy half dollar, which had a silver content of approximately 40%. The step was taken out of necessity, because of the rising shortfall between world mine production and consumption. It was important to divert the 35 to 40 million oz of silver per year used for the minting of this coin into the open market, where it would be available for industrial consumption. This decision was important, not only for its practical effect but also for what it symbolized. Only four years earlier, in 1965, the Treasury had used 320 million oz of silver" for the full range of coinage. Now not an ounce of silver goes into the United States coinage. The reason is simple and yet complicated. For many years the U.S. Treasury had purchased silver at prices which provided a subsidy to domestic producers. As a result, silver producers were eager to sell to the Treasury, and that agency built up a huge supply of the metal -almost 2 billion oz by- 1961. But, as the free-market price neared $1.29, the basic melt value of the coinage, the Treasury became a seller of silver, not a buyer, and its stock was depleted rapidly. The Treasury lost more :than a billion ounces of silver in the years 1962 through 1965, and it continued to lose silver, both through coinage and through sales to consumers, through 1969. The Government continued to sell silver to consumers at the rate of 1.5 million oz a week, even after terminating the 40% silver Kennedy half dollar. But it was apparent that the Government stocks could last no more

Jan 1, 1976

By CHARLERS R. FETTEE

A slight decrease in drilling activity occurred in the oil fields of western Pennsylvania during 1945 and a considerable decrease in the shallow-gas territory (Upper Devonian or higher). The number of deep tests (Middle Devonian or deeper) completed was two less than in 1944 and these did not open any new reserves of natural gas. Thus far, no commercial oil has been encountered in sands below the Upper Devonian in Pennsylvania. Oil production declined 8 per cent.

Jan 1, 1946

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By S. H. Chauvenet

HARRISBURG is situated on the Pennsylvania Railroad, one hundred and five miles from Philadelphia, two hundred and forty-eight miles from Pittsburgh, and ninety miles from Baltimore, and has running through it the Pennsylvania, Northern Central, Philadelphia and Reading, and Cumberland Valley Railroads, and the Pennsylvania Canal. Surrounded by a thickly settled farming country, from which to draw native labor, within easy distance of anthracite and bituminous coal, with ores and limestone near at hand, and with the Susquehanna River as a never-failing water supply, Harrisburg has advantages for manufacturing which warrant the investment of the capital that has already been made, and has a future as a manufacturing city second only to Pittsburgh and Philadelphia. THE PENNSYLVANIA STEEL COMPANY, L. S. BENT, SUPERINTENDENT. The works of this company, the largest in Harrisburg, lie between the Pennsylvania and the Philadelphia and Reading Railroads, on. the Pennsylvania Canal, and are essentially devoted to the manufacture of Bessemer steel rails. Capital stock, $2,000,000; invested in business, $5,000,000; wages per month, $80,000; employs 2000 men; capacity, 100,000 tons of rails per year, which is being increased to 130,000 tons. The plant, as it now stands, comprises five Bessemer converters, two 7-ton and three 8-ton converters, two 15-ton open-hearth furnaces in operation, and two 30-ton open-hearth furnaces in course of construction, one blooming mill, one rail mill, seven steam hammers, two blast furnaces in operation, two blast furnaces in course of construction, foundry, pattern $hop, machine shop, blacksmith shop, and frog shop, and merchant mill in course of construction. Bessemer No. 1 was built in 1865, with two 7-ton converters, 2 spiegel cupolas, 3 feet diameter, and 3 iron cupolas 6' 6" diameter,

Jan 1, 1882

By Robert M. Weidenhammer

For years before the war, Coal had the reputation of being a sick industry. Currently it is operating at peak production and succeeding pretty well in keeping out of the red. But, says Mr. Weidenhammer, it will have a relapse as soon as the war ends unless (1) working capital can be built up; (2) it gets the support of the people and Congress; and (3) a truly long-range national fuel policy is formulated.

Jan 1, 1943

By W. W. Wirth

RESEARCH looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than develop-ment work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand.

Jan 1, 1940

By J. W. Buch

IN THE FIELD of track haulage, interest has seemed to center on the question of larger mine cars both for handling material from loading point to shaft bottom or surface, and for shuttle service. Saving of time in car changing is obvious if larger cars are used. In addition, shorter trips result where car transportation is from face to opening without transfer. This also brings about side-track and equipment savings. Track shuttle service, using large automatic-dump cars (10 tons) between loading machines and trip loading point, has been a satisfactory solution for the operator who mechanizes a working mine regularly equipped with a large number of small mine cars. This development in track shuttle haulage, has made track installation and maintenance increasingly important, requiring closer supervision.

Jan 1, 1942

H. H. Stoek, Scranton, Pa. (communication to the Secretary): Mr. Rothwell's condemnation of my paper on the International Correspondence Schools as not giving an impartial view of the whole field of such enterprises, because it was confined to the description of a single one, might be legitimate if I had undertaken or professed to do anything else than that which I was requested by the Secretary of the Institute to do—namely, to give an account of this particular institution. This is a sufficient answer to all his direct or implied criticisms upon my omission to mention either persons or organizations outside of the special limits set for me. Recognizing fully that personalities have no place whatever in the Transactions, I regret the necessity of making the following statement in answer to Mr. Rothwell's charge that I omitted to give due credit to Mr. Ewald, a former principal of the International Correspondence Schools. The Colliery Engineer School of Mines was started in 1891, and its first student was enrolled October 16, 1891. During the fall of the same year the mine-mechanical course was laid out along the same general line that had already been followed in the mining course. This mine-mechanical course was the foundation from which sprung the later developments of the several mechanical courses. The latest circulars of information of the International Correspondence Schools give the following as their distinctive features: (1) courses of instruction for particular occupations,

Jan 1, 1900

By Charles S. Barrett

There is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 2o years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold-worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calori-metric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.l When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. I, which represents a narrow beam containing X-rays of many wave lengths (''general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

By E. W. Pehrson, J. W. Furness

THE five charts presented here- with are part of an original group prepared by the U. S. Bureau of Mines showing the international trade in the principal metals and metallic ores. Charts 011 anti- mony, chromite, copper, lead, manganese, mercury, nickel, tin, tungsten, and zinc were published in the February, 1936, issue of the Engineering and Mining Journal. Those shown here include bauxite, aluminum, iron ore, pig iron, and the platinum-group metals.

Jan 1, 1936

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950

Erwin S. SperRy, Bridgeport, Conn.: The analysis of refined copper is a subject of great importance, and has not received the attention it deserves. Copper metallurgists, therefore, will welcome the paper of Mr. Heath with satisfaction. The state of the art of the chemical analysis of copper has been such that consumers, if they could not afford to run any risk, have been obliged to buy copper from the smelter having the best reputation, and a specification for copper to meet certain requirements could not be drawn up by the mere giving of the chemical constituents. Mr. Heath has brought the analysis of the copper to such a state that when a specification calls for copper " equal to Lake copper " one will know immediately what percentage of the pure metal to expect. It seems to be a pretty well established fact that the copper of Lake Superior is practically free from antimony and bitmuth ; and, with the exception of arsenic, the other elements are easily separated from copper by electro-deposition in an acid solution. The authorities differ in regard to the question whether antimony is deposited with the copper in an acid solution. Classen* recommends the employment of a solution containing 10 per cent. of free nitric acid, sp.gr.1.21, and the strength of the current from 0.3 to 0.4 ampere, in order to prevent the other metals from being deposited with the copper; and for this reason, I presume, the method has been generally used. I, myself, have been accustomed to use such a solution for the analysis of copper-alloys, but have found that for such alloys only a small quantity of nitric acid is necessary, if sulphuric acid is present in sufficient amount to give the solution the required conductivity.

Jan 1, 1898