Search Documents

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By AIME AIME

A PERIOD of business depression and falling prices always raises questions as to the possible responsibility of the monetary or banking system. This is natural enough, for it is agreed that the supply of money or credit is a very important factor in modern business and in prices. However, it is far from being the only important factor. One of the chief merits of the gold standard is that under its workings the supply of currency and credit is regulated automatically to the masimun extent, in- stead of by the control of any arbitrary authority. The supply of new gold comes from the mines, and mining is free. It is distributed among the countries by the currents of trade and the play of economic forces, with the general result that the distribution tends to be in accordance with the economic development of the countries and their ability to use it or command it. Inasmuch as the accumulated stock of monetary gold is very large in comparison with the annual additions, the total avail- able supply changes but little from year to year, and it may be assumed that price-changes that are properly chargeable to gold will take place gradually rather than suddenly.

Jan 1, 1930

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By Olav Mellgren

Part I. The interaction between potassium ethyl xanthate and lead salts has been studied thermo-chemically. It is shown that ethyl xanthate reacts with lead carbonate, basic carbonate, thiosulfate and sulfate according to principles of simple chemistry, whereas reactions with lead sulfite, metasulfite, basic thiosulfate and hydroxide at high pH are associated with secondary reactions. A new compound "xanthogen thiosulfate" is postulated. Part 11. Adsorption of ethyl xanthate on galena has been studied quantitatively and thennochemi-cally. It is shown that an ion-exchange mechanism governs the adsorption process and that the heat of adsorption of xanthate on galena is equivalent to the heat of reaction of ethyl xanthate with bulk lead salts. It is concluded that the entropy content of the surface "compound" on galena is different from that of a corresponding bulk lead salt. Alkali depression is in part shown to be due to the instability of the xanthate-galena system at high pH and to the formation of basic lead salts. Sulfate and carbonate ions are shown to have a stabilizing effect on the xanthate-galena system. PARTI. THERMOCHEMISTRY OF ETHYL XANTHATE AND OF ITS REACTION WITH LEAD SALTS In the past little attention has been paid to the chemistry of lead xanthate. It is known that xan-thates form slightly soluble compounds with lead and that suspensions of lead xanthates in alkaline solution decompose rather readily.' The solubility of lead ethyl xanthate is of the order of 2.6 x 10-6 moles per 1. At increasing pH the xanthate concentration of a saturated solution contains more xanthate. Thus at pH 11 this xanthate content is about 100-fold larger than at pH 7.1 Xanthates are known to be consumed when added to a suspension of slightly soluble lead salts such as lead sulfate and lead carbonate. It is unknown to what extent this xanthate consumption is due to a simple chemical reaction because, frequently, observations are made which reveal secondary reaction products in such reactions. Thermochemical study of the reaction between xanthate and lead salts offers a means to clarify the significance of these reactions as the enthalpy changes can be accurately predicted from heat of formation of lead salts in pure solution reactions. In the present work the heats of formation of lead ethyl xanthate from potassium ethyl xanthate and lead salts are determined and some thermochemical aspects of xanthate in solution are studied. The results of these investigations are presented in Part I. In Part II the heat of adsorption of ethyl xanthate on galena surfaces is presented. All enthalpy changes were measured directly in a microcalorimeter. Calorimeter: The calorimeter used for measuring enthalpy changes was similar to that used by Redinha and Kitchener2 which was based on a description by Derbyshire and Marshall.3 Other useful references4,5 are listed. A sketch of the calorimeter

Jan 1, 1967

By David R. Mitchell, Ernest M. Spokes

There is evidence that study of minerals now considered to have susceptibilities too low for magnetic separation should be continued. Present concepts may be false. INFORMATION on magnetic properties of minerals other than magnetite is scanty and sometimes erroneous. Often there is no information at all. W. R. Crane's table of tractive forces published in 1901 is still the best guide in the field, but Crane's data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930's work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolframite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs. Gouy Method for Determining Magnetic Susceptibility: The Gouy principle has been adequately described in the literature1-3 and applied in various ways.'- It may be summarized by stating that a body of material (gas, liquid, solid, or powder mixed with gas or liquid) of cylindrical shape changes in apparent weight if suspended with one end in a zone of higher magnetic field strength than is found in that portion of the field surrounding the other end of the cylinder. This may be expressed as K2 - K1 A (H2 - H2) - mg. [1] In determining the susceptibility of mineral specimens by the Gouy method, the mineral is reduced to a fine powder and packed in a glass weighing tube. Precise measurement of the bore and depth of the tube is made unnecessary by a calibration procedure. Using the basic expression of Eq. 1, Hoare"

Jan 1, 1959

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1&apos; shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter&apos;s&apos; original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By J. R. Lucas, R. L. Frantz

Mine sealing programs for the alleviation of acid mine drainage were begun by the Federal Government in the &apos;30&apos;s. As part of an acid mine research project to The Ohio State University, a field test was undertaken to determine the effectiveness of mine seals for reducing mine acid. Details of the tests made at the McDaniels mine show the feasibility of air-sealing and flooding an acid-producing drift coal mine. Work by the University continues. The Federal Government undertook in the early thirties an extensive mine sealing program for the alleviation of acid mine drainage. In the states of West Virginia, Ohio, and Pennsylvania many general summaries have been made on this program but no critical evaluation with supporting data has been found on the effectiveness of mine seals for reducing mine acid. Because of this it was decided to undertake a field testing program as part of an acid mine research project of the Engineering Experiment Station, The Ohio State University. The objective of this phase of the project was to develop and install a field research laboratory for acid mine drainage studies. Specifications for such a mine laboratory were developed and resulted from the following considerations: 1) Size and preservation—the test mine shou1d be of limited size to permit frequent and detailed examinations; it should be in a reasonably sound condition to permit safe entry. 2) Isolation—the mine should be physically separated from all other mines. 3) Openings—a minimum number would be desirable to reduce the sealing problem. 4) Structure—the mine especially near the openings should be structurally sound. 5) Acid production—the mine should be producing significant quantities of acid. After considerable searching, the McDaniels mine was selected in the Hocking coal field in Vinton County just above Lake Hope State Park in southeastern Ohio. The small drift mine in the middle Kittaning coal consisted of two small rooms with one mine opening about 6 ft above a seasonal stream bed. Before it was finally decided to seal the mine, a short study was made of the acid drainage over several months. Fig. 1 shows a plot of acidity (milligrams per liter), flow (gallons per minute), and acid production (pounds per day) vs time over the sampling period. Because the coal was overlain with a porous sandstone, the mine drainage was consistent the year around even though the mine was

Jan 1, 1961

By John F. McElhiney, Hosseim Kazemi

This chapter is a review of fluid flow and mass trans- port in fractured rocks. The topics include: single-phase and multiple-phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

By Maxwell Gensamer

Jan 1, 1960

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975