Search Documents

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By J. G. Haymes

This report by the Bureau of Mines is the first of two proposed papers on evaluation of spectrophotometric, spectrographic, polarographic, and other analytical methods for quantitatively determining impurities in high-purity tungsten. Some of the methods described are standard methods that have been successfully applied to determine low-level impurities, several are modifications of known methods, and some procedures are entirely original. The Bureau of Mines is actively engaged in tungsten research because tungsten has an extremely high melting point, in fact the highest of any known metal. The metallurgist must know the content of impurities in tungsten because of the marked effects even micro amounts of impurity elements have on its physical properties. The Bureau procured a number of analyzed samples of above-average purity from research laboratories of companies engaged in production and fabrication of tungsten. These samples were investigated by the analytical procedures of those companies for several metallic impurities. Subsequent analytical laboratory determination of impurities in these samples agreed with the analyses as reported. With this assurance that analytical methods were basically accurate for metallic impurities, procedures for the determination of several of these elements were modified to lower the limits of detection and increase the sensitivity of methods. Carbon and the gases hydrogen, nitrogen, and oxygen were determined by standard instrumental methods, modified to provide greater sensitivity for reliable determinations when content of these elements was low. After the reliability of the modified procedures was affirmed, they were used as a product evaluation guide in the development of a vapor-plating technique for the production of high-purity tungsten. The following list of elements can be determined by one or more of these methods: AI, B, Be, Ca, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, S1, Sn, Ti, V, and Zn. In addition, a vacuum-fusion method for the determination of H, N, and 0, and a conductometric method for carbon are described. Lower limits of determination and detection for each element listed are given.

Jan 1, 1962

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By M. Vanpée, H. G. Wolfhard

Jets of hot gases issuing into explosive gaseous mixtures are efficient agents of ignition . The ignition temperature is defined as the temperature of the jet as it enters the cold explosive mixture which is just high enough to produce ignition . Such data have been published recently.5/ The investigators note especially that no correlation seems to exist between hot - gas ignition temperatures and spontaneous ignition temperatures , although there is a rather loose relation with limit flame temperatures . Before a more quantitative theory of the hot - gas ignition process can be attempted effectively , several questions must be answered : ( 1 ) Can the reactions leading to ignition be described by an Arrhenius type activation energy? ( 2 ) Is ignition preceded by an induction period ? ( 3 ) What is the rate - determining process of the ignition ? (4) And how does turbulence affect this type of ignition ?

Jul 1, 1960

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By Juan Garcia de Blas

O presente trabalho aborda o desenvolvimento de liga titânio-nióbio obtida por metalurgia do pó no qual foi introduzida uma operação de extrusão angular em canal (Equal Channel Angular Pressing - ECAP) com o propósito de promover uma consolidação que favorecesse a homogeneização na etapa posterior de sinterização. Após o processamento o material foi caracterizado por microscopia ótica e microscopia eletrônica de varredura (MEV/EDS). Os resultados preliminares indicaram a importância da redução do tamanho das partículas de nióbio.

Aug 17, 2017

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

Jan 1, 2002

By A J. Eggers

With gold first discovered at Carrick in 1864, exploration and mining on the Carrick Goldfield in Central Otago, New Zealand, has now been ongoing for more than 130 years. Recorded historical hard rock production from up to 52 different mining claims from 1864 to about 1921 is 24,047 ounces (oz) of gold.   Since 1980 Amoco Minerals New Zealand Limited, CRA Exploration Pty. Limited, Amax Gold Mines New Zealand Limited and Summit Gold (New Zealand) Limited have conducted modem systematic exploration campaigns targeted at locating shear controlled gold bearing quartz lodes and stockwork deposits. More than NZ $1million has been spent by these companies on aerial photography, geological mapping, stream sediment surveys, soil and rock chip geochemistry as well as reverse circulation (RC) percussion and diamond drilling.   RC drilling by Summit Resources in 1997 has identified a 1,500 m long zone of low-grade gold mineralisation at Lower Carrick, with an average grade of 1.00 g/t Au over a 14 m average thickness. This gold mineralisation, hosted within a low angle shear zone, has analogies with the Hyde-Macraes Shear Zone in eastern Otago. Recent exploration and drilling at Carrick has revealed the potential to discover large (>0.5 million ounce (Moz)) low-grade bulk shear controlled quartz vein and stockwork gold deposits similar to those now being mined at Macraes.

Jan 1, 1997

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, WA plant is briefly described.The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1980