Search Documents

By Paul C. Hyndman

The U.S. Bureau of Mines investigations of the three subunits (fig. 1) of the Homestead RARE II area (No. 6291) revealed no evidence of mining activity or mineral deposits in the area. The Iron Dyke Mine, 3 mi (5 km) outside the study area produced ore between 1916 and early 1982 from a volcanogenic massive sulfide deposit in the Permian volcaniclastic Hunsaker Creek Formation of the Seven Devils Group. The Hunsaker Creek Formation does not crop out in the RARE II area, but extends into the area beneath Miocene flows of Columbia River Basalt. The abundant basalt in the area could be used as aggregate or dimension stone, but equivalent deposits exist closer to markets. INTRODUCTION Location and Access The Homestead RARE II area (fig. 1) encompasses 6260 net acres (253U ha), in three units, of the Wallowa-Whitman National Forest in Baker and Wallowa Counties, Oregon. Two small units of 160 and 300 acres (65 and 120 ha) are 5 mi (8 km) north and east of the main study area. Homestead, Oregon, on the Snake River, is about 3 mi (4 km) south of the two small areas, and about 3 mi (4 km) northeast of the main study area. Peripheral access is provided by State Highway 86, U.S. Forest Service Road 39, and ancillary roads and trails.

Jan 1, 1983

In all the industries that require blasting operations using explosives, there exists numerous unwanted side effects of the blast which may pose as environmental hazards. These hazards face prominence, especially in India, where there are very stringent rules and regulations governing the use of explosives. The environmental hazards associated with blasting operations as a whole can be tacked successfully to a certain extent depending upon the ultimate expectations of ,the post-blast effects and the limitations of the environmental obligations as specified by the authorities from time to time and from place to place. The main parameters which require attention to limit the post-blast results to the optimum level are ground vibrations, dust pollution, gas pollution, air blast effects, noise pollution & fly rocks etc.

Jan 1, 1995

By J. van Deventer

Ion exchange is widely used in hydrometallurgical operations for the recovery and purification of valuable metals. Special chelating resins have a high affinity for specific elements, allowing the selective removal of low levels of impurities from a background of highly concentrated valuable metal. Solvent-impregnated resins have been added to this group more recently, expanding the treatment options. These products find application in the purification of cobalt-rich liquor prior to the production of high-purity metal or metal salts. Impurities in copper-cobalt circuits that are typically targeted by ion exchange include iron, uranium, copper, zinc, nickel, bismuth, and antimony. Ion-exchange resins can also be used to treat tailings, thereby recovering additional valuable metal and improving the Environmental and Social Governance credentials of the operation. This article takes a look at various applications of ion exchange in copper-cobalt operations

Jan 1, 2023

By W. A. McKinney

The segregation process consists of heating crushed oxidized or mixed oxide-sulfide copper are with a copper-volatilizing salt and carbonaceous material at about 750° C. to produce metallic copper which is recovered from the furnace calcines by conventional sulfide flotation. The Bureau of Mines made a number of bench-scale laboratory tests on two copper ores to determine the relative merits of using halogen salts, potassium chlorate, or various salt mixtures as volatilizing agents in segregation of the copper. Laboratory investigation of typical siliceous and calcareous oxidized ores revealed that sodium chloride was a better segregating agent than the other salts. Calcium chloride, magnesium chloride, sodium fluoride, or potassium chlorate gave nearly as good segregation as the sodium chloride on the siliceous ore. Segregation of the calcareous ore with calcium chloride was nearly as good as that obtained with sodium chloride, but inferior segregation resulted when magnesium chloride, sodium bromide, or potassium chlorate was employed. The use of sodium bromide or sodium iodide on the siliceous ore, and of sodium fluoride or sodium iodide on the calcareous are, gave appreciably poorer segregation than sodium chloride or the other salts. Other tests of the ores, using mixtures of sodium chloride and the other halogen salts or potassium chlorate, gave segregation approaching that obtained with sodium chloride.

Jan 1, 1962

By A Rozendaal

Namakwa Sands, a heavy minerals beneficiation business situated along the west coast of South Africa, is a major producer of titanium slag, pig iron, ceramics quality zircon and rutile concentrate to the international export market. The bulk of the economic mineralisation, which includes zircon, rutile, ilmenite and leucoxene is hosted by a late Cainozoic aeolian succession overlying remnant palaeo-strandline sediments. Relatively younger duricrust layers that cement a significant part of the generally unconsolidated ore compounds the challenging processing character of the primary mineralogy. The complex nature and hardness of the duricrust ore influence their mineability negatively, and can potentially destabilise downstream ore preparation processes. Effectively, up to ten per cent of the entire mineral resource is sterilised as the present infrastructure is not geared to treat the hard-mineralised ore. The metallurgical performance of the primary processing stage, which entails wet density separation, is strongly a function of the quality of the heavy mineral assemblage, liberation state of the economic minerals and slimes content. Elevated concentrations of garnet, a gangue contaminant exhibiting similar physical characteristics as the economic minerals, subtract substantially from the recovery performance of the secondary concentration process, which comprises mainly wet magnetic separation. By contrast, the intrinsic mineral purity of the economic fraction governs its successful recovery to saleable products as stringent product quality specifications apply. Improved mine planning through geometallurgical enhancement of the existing mineral resource model is envisaged to benefit the entire Namakwa SandsÆ mineral beneficiation chain, ultimately aiming to optimise mineral resource utilisation.

Jan 1, 2008

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By Sir Robert Hadfield

SINCE the writer has been intimately connected with the development of manganese steel for many years, some remarks upon the early work with regard to the rolling and forging of this material might he of interest, and particularly as to the question of rails of special quality and of superior wearing qualities. In a paper on Iron Alloys, with Special Deference to Manganese Steel, read before this Institute at the International Engineering Congress in Chicago in 1893,1 the writer mentioned that, about 20 years ago, his firm in Sheffield produced railroad material, such as tires and axles, of forged and rolled manganese steel, thus showing that this product could be manipulated and worked up into the various required forms. The tires illustrated in the paper referred to above formed a particularly difficult class of work to produce in a special steel, but no special obstacles were met with Although there was no difficulty at that time in making and producing manganese steel in various forms, forged, rolled or pressed; nevertheless, on account of its higher expense, sufficient encouragement

Jan 2, 1914

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

By J. L. Wiley

THIS REVIEW contains abstracts of the technical literature and patents dealing with the history, development, and commercial application of the Bergius and related processes for the hydrogenation, under greater than atmospheric pressures, of liquid and solid carbonaceous materials such as coal, lignite, their distillation and extraction products, pitches and tars, and petroleum and its distillation residues. An attempt has been made to include abstracts of all the published information on this process and of as much of the captured foreign documents and reports compiled therefrom as could consistently be reviewed during the time allotted for the work. Contact with the current literature and patents and review of the foreign documents will be continued and the information will appear in Synthetic Liquid Fuels Abstracts, which is being issued bimonthly as a Bureau of Mines publication. The material in this review is divided in two sections-literature (part I) and patents (part II)-and each of these is arranged alphabetically by author or patentee with further chronological arrangement under each author or group of authors. Secondary authors and patentees as well as assignees are cross-indexed to the main entry. In serial articles or reports the complete series appears in the alphabetical arrangement according to the author of the first member of the series. Succeeding members as well as secondary authors are entered as cross references; Titles of the journals are used as the authors in anonymous references. By following such a procedure, an author index is not required. However, a detailed subject index and a numerical patent list by countries are given as part III.

Jan 1, 1950

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006

Beyer Barometric Condenser The Ingersoll-Rand Co. is now offering to the trade complete steam­condensing plants for all service conditions. This equipment includes the Beyer barometric condenser, for' which the company has secured the patent rights, Imperial duplex and Ingersoll-Rogler straight-line reciprocating dry vacuum pumps and, where required, Cameron simplex and centrifugal pumps. The Beyer barometric condenser is of the counter-current type, in which air and cooling water flow in opposite directions. The steam inlet is at the bottom of the condensing v el, the water inlet above and the air-removal opening at the top. The sheets of cooling water over owing the pool at the inlet point meet the entering steam. The two are brought into intimate contact by conical baffle plates which assist the water to absorb to its full capacity the latent heat of the steam. The non-condensable air liberated in the condensing action rises through the falling water to the removal point at the top, being cooled to practically the temperature of the incoming water. It is also to be noted that ample opportunity is given for the removal of the air content of the water before

Jan 8, 1916

The green field site is one that has no history of mining and as such it presents the designer with a blank canvas, on which any number of drill and blasting options can be drafted. No matter which mining method is selected all technology and experience will need to be acquired from outside sources, applied quickly and produce the right results. North Limited, in joint venture with the Sumitomo Group (20 per cent), have developed AustraliaÆs first block cave mine at Northparkes in New South Wales, Australia. This innovative and large scale mining project was taken from a green field site in November 1993 to a fully commissioned block cave mine in December 1997. NorthparkesÆ Endeavour 26 mine is now producing at a rate of 3.9Mt per annum from a 27Mt ore block. Prior to 1993 no history of mining activity existed at Northparkes. The rock had never been blasted and many questions were raised about how it would behave. While it was clear that the Endeavour 26 (E26) orebody contained geotechnical properties appropriate to block caving, the blasting methods required to establish a block cave mine had never been used in Australia and no designs were available. The joint venture partners had no prior experience with block caving and it was immediately apparent that this blasting technology would have to be acquired from foreign sources and applied to the unique local conditions. Conceptual designs for the block cave drill and blast were first drafted in 1994, first issued for drilling in December 1995 and first blasted in January 1996. 470 km of drill metres and four million tonnes of rock were blasted to complete the undercutting project by September 1997. This paper will provide those developing new drill and blast projects with an inside view of how one small technical team solved many design challenges to successfully construct AustraliaÆs first block cave mine under strict quality controls and ambitious time constraints.

Jan 1, 1998

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997