Search Documents

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By Greaves M. C

X-ray fluorescence spectroscopy used for the analysis of mill samples results in improved control of flotation concentrators.Techniques and equipment for sampling pulp streams, filtration and drying, grinding, briquetting and X-ray fluorescence analysis of samples have been developed.The current methods in use permit the analysis for lead and zinc in six pulp samples within 30 min total elapsed from the start of sampling. The X-ray method gives a precision at least equal to the former routine wet-way assay methods.The equipment is used also for pilot plant control, as a means of solving complicated analytical problems and in the rapid qualitative analysis of exploration samples.INTRODUCTIONIn milling and concentrating operations, classical methods for the assay of lead and zinc have been mainly of use for accounting purposes and for the post-mortem examination of plant operations, but have been of little value for rapid mill control. Where attempts have been made to apply these methods to control assaying, it has been necessary to modify the procedures and introduce short cuts which have tended to reduce their reliability.Even with these shortened procedures, the time taken to obtain a limited amount of information rendered them of little value for the control of milling operations where sudden, large fluctuations can occur. In recent years, a number of new and rapid analytical techniques, based on physical rather than chemical principles, have been introduced.These include direct reading emission spectroscopy, x-ray fluorescence spectroscopy and atomic absorptionspectroscopy.

Jan 1, 1964

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

By Daniel N. Adams

The University Link project extends Seattle?s light rail from downtown to University of Washington (UW). It includes 5.0 kilometers (3.15 miles) of twin-bored, 6.4 meters (21 feet) excavated diameter tunnels, and two cut-and-cover stations. The Capitol Hill Station (CHS) requires an excavation 170.7 meters (560 feet) long, 22.6 meters (74 feet) wide, and 22.9 meters (75 feet) deep. The University of Washington Station (UWS) requires an excavation of about 238.4 meters (782 feet) long, 21.3 meters (70 feet) wide, and 33.5 meters (110 feet) deep. The project is within the glacially diverse soils of the Puget Sound region, below groundwater. This paper highlights major station and tunnel design elements, including the approach to support of excavation at both station boxes, and the site staging requirements.

Jan 1, 2008

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By S. Read, G. Cook

The Hoek-Brown failure criterion is often applied to a wider range of rocks than the isotropic rock masses to which it is strictly applicable. This paper evaluates the patterns of defects in rock masses using spherical projection contour plots of samples of randomly-generated orientations and datasets from mapping of New Zealand closely-jointed greywacke rock masses. Two indices from the contour plots - the area within the 1% contour (A1%) and maximum concentration (Cmax) are introduced for distinguishing uniform (isotropic), random or regular defect patterns. The indices provide a potential extension to current guidelines on the use of the Hoek-Brown failure criterion. The paper also outlines kinematic checks to assess the influence of defect clusters on rock mass strength. Das Hoek-Brown Bruchkriterium, das strikte nur fuer isotrope Gefuege gilt, findet oft einen viel weiteren Anwendungsbereich. Diese Arbeit bewertet diverse Dispersionsmuster der Defekte einer Gesteinsmasse. Wir vergleichen in sphaerischer Projektion (1) Beispiele zufaelliger Orientierung von Defekten und (2) Felddaten ueber neuseelaendisache engstaendig geklueftete Grauwacken. Die Projektionen werden durch die Indices A1% (Flaechenanteil des 1%-Bereichs) and Cmax (Hoechstkonzentration) gekennzeichnet, welche isotrope, zufaellige und regulaere Muster unterscheiden und die aktuellen Richtlinien zum Hoek-Brown Kriterium ergaenzen. Wir testen ferner Defektgruppen der Gesteine kinematisch auf ihren Einfluss auf Massenfestigkeit. Le critère de rupture de Hoek-Brown est souvent utilisé sur une variété de roches plus étendue que les masses rocheuses auxquelles il est strictement applicable. Ce travail évalue la distribution des défauts au sein d'une masse rocheuse en utilisant une projection sphérique des contours d'échantillons d'orientations générées aléatoirement et de données de cartographie provenant de greywackes à joints rapprochés de Nouvelle Zélande. Deux indices de cette projection - la zone des contours en dessous de 1 % (A1%) et celle de concentration maximum (Cmax) sont introduites pour distinguer les répartitions uniformes (isotropes), aléatoires ou régulières. Ces indices fournissent une extension potentielle aux règles d'utilisation du critère de rupture de Hoek-Brown. Ce travail utilisent également les contrôles cinématiques pour évaluer l'influence des groupes de défauts sur la résistance de la masse rocheuse.

Jan 1, 2003

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By W. Wittke, J. Gattermann

ABSTRACT: One alternative to close a radioactive waste repository in rock salt is the construction of a “Cross Section Closure (CSC)“ sealing barrier. The proposed material for the CSC is highly compacted bentonite. To investigate the swelling behaviour of a highly compacted bentonite a large number of laboratory tests were performed. In addition, large scale model test were carried out to demonstrate the development of a nearly homogeneous and isotropic swelling pressure. The results of the large scale model tests were interpreted numerically based on the models for stress-strain behaviour and water uptake which are implemented in the finite element codes FEST03 and HYDOPO. The investigations show a good agreement of the results of the model tests and the corresponding analyses and show, that the theoretical models are capable of describing the behaviour of sealing structures based on highly compacted bentonite. ZUSAMMENFASSUNG: Eine Möglichkeit für den Verschluß eines Endlagers für radioaktive Abfälle im Steinsalz ist die Konstruktion einer Querschnittsabdichtung aus hochverdichtetem Bentonit. Zur Untersuchung des Quellverhaltens von hochverdichtetem Bentonit wurden eine große Anzahl von Laborversuchen durchgeführt. Um die Entwicklung eines nahezu homogenen und isotropen Quelldrucks nachzuweisen, wurden darüber hinaus auch Modellversuche in größerem Maßstab durchgeführt. Die Ergebnisse dieser Modellversuche wurden im Hinblick auf die Wasseraufnahme und das Spannungs-Verformungsverhalten mit Hilfe numerischer Berechnungen mit den finite Element Programmen FEST 03 und HYDOPO interpretiert. Die Untersuchungen zeigen gute Übereinstimmungen zwischen Versuchs- und Berechnungsergebnissen. Die numerischen Modelle sind somit geeignet, das Verhalten von Abdichtungsbauwerken aus hochverdichtetem Bentonit zutreffend zu beschreiben. RÉSUMÉ: Une possibilité pour fermer un dépôt final de déchets radioactifs dans sel gemme est la construction d'un étanchement de coupe transversale, fabriqué de bentonite fortement compacté. Pour étudier le comportement de gonflement de bentonite fortement compacté, de nombreux essais en laboratoire ont été exécutés. En outre, des essais sur modèle sur une plus grande échelle ont aussi été exécutes afin de prouver le développement d'une pression de gonflement à peu près homogène et isotrope. Les résultats de ces essais sur modèle étaient interprétés en vue de l'absorption d'eau et du comportement contraintes-déformations par le moyen de calculs numériques avec les programmes d'éléments finis FEST03 et HYDOPO. Les études montrent de bonnes conformités entre des résultats d'essai et de calcul. Les modèles numériques sont ainsi capables de décrire justement le comportement d'ouvrages d'étanchement fabriqués de bentonite fortement compacté.

Jan 1, 2003

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By John Rusnak, Christopher Mark

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load frame and point load testing of coal measure rocks in six states. More than 10,000individual test results, from 908 distinct rock units, were used in the study. Rock lithologies were classified into general categories and conversion factors were determined for each category. This allows for intact rock strength data to be made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By McDonald G. G

In the deformation of a metal or a single-phase alloy all the crystals composing the metal after their shape in a similar manner as the metal in bulk and to about· the same extent. This is not the case in an alloy consisting of two phases of different resistance to plastic deformation. In such an alloy the two phases take part in the deformation approximately in inverse proportion to their hardness, at least at the beginning of the deformation. (1) The hardness difference becomes less in the course of the deformation and thereby the deformation more equal. The phenomena occurring during cold-rolling of some two-phase alloys have been investigated by H. Unckel who made statistical grain measurements of the degree of deformation of the two phases after various reductions by rolling and also microscopical observations of the flow in the neighbourhood of the grain boundaries. Because of the different relative flow of the two phases, the normal flow is disturbed in the vicinity of their boundaries, and some additional plastic flow must take place in these regions, the disturbance being levelled out at some distance from the boundary. The deformation of the two phases present simultaneously in the material should thus be different from that of each phase separately. The investigation of theimportance and the effects of this interaction of crystals of different phases is the subject of this paper.The deformation of crystals occurs as a gliding of crystal layers following crystallographic laws. In consequence of this slip the crystals composing the material tend to assume a common orientation, i.e. some crystallographic axes tend to become parallel to each other in all the crystals. The type of this preferred orientation depends on the type of the crystal and the working process. Any change in the mechanism of deformation results, therefore, in a change in the preferred orientation. Such a change in kind and degree of preferred orientation will, therefore, also occur if the interaction of crystals in a two-phase alloy gives rise to a mechanism of deformation different from that in the free phases.The present paper describes a study of the preferred orientation, the microstructure and hardness in wires of brass drawn to various extents.The development of preferred orientations in the two phases with increasing reduction was followed up in various layers of the wire.EXPERIMENTAL DETAILSThe experiments were carried out with a commercial 5 S.W.G. wire (0,212 in. diameter) containing: 62·7% Cu, 37·3% Zn, very faint traces...

Jan 1, 1941

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

By James R. Wait

The present final report constitutes the total productivity of a series of contracts from the U.S. Bureau of Mines and the Institute for Telecommunication Sciences over the period 1971-1979. The emphasis on the research has been analytical. In this "executive summary" we give a succinct description of each phase of the investigation. In the first phase of the investigation that was stimulated by the National Academy of Engineering, we concentrated on the analytical studies of techniques relevant to mine rescue. Several specific procedures for locating a buried source were analyzed. In the next, but overlapping phase of the investigation, we dealt with the fundemental character of how electromagnetic waves propagate in mine tunnels. At the outset we allowed for the finite conductivity of the tunnel walls and the presence of axial conductors such as cables, pipes, and tracks. The third phase of the investigation was devoted to the analyses of various specific geophysical engineering problems. The related fourth phase dealt with the general subject of non-destructive testing of wire ropes such as used for mine hoists.

Jan 1, 1980

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By M. Weatherspoon, S. Gebo, K. Prisbrey

Our objective was to develop a transfer function model of phosphate heap leaching for design, optimization and control. The procedure included analysis of time-lapse photography of a laboratory heap. Our experimental results confirm the predicted system transfer function kinetics. Our conclusion was that the transfer function and z transform that we have developed will allow us to control flow rate and pH online.

Jan 1, 2001

By Y Öztas, S McKinley, T Baker

The Kisladag Mine, Turkey, is a large porphyry gold deposit which is mined by open pit methods. In operation for over ten years, Kisladag provides an excellent example of how attention to a geologic feature, namely hydrothermal alteration, became a very effective predictive geological tool for planning and operation. The alteration domains were initially used as a geological tool to assist with establishment of resource model domains and to guide delineation drilling, but they were soon recognised to be correlative to geotechnical characteristics (affecting pit slope angles) and metallurgical performance (heap leach recoveries). Recent developments in spectral processing allow the systematic quantification of complex overlapping alteration phases and have greatly improved the ability to rapidly define internally consistent alteration domains for geotechnical and geometallurgical purposes.Alteration at Kisladag comprises a central core potassic (K-feldspar-biotite) zone, a tourmaline-white mica enveloping zone, an advanced argillic lithocap on the deposit’s eastern side and an overprinting pervasive argillic zone. These alteration zones and their distribution were based initially on strictly qualitative, visual mineralogical logging of diamond drill core. With the need for more accurate and consistent identification of the alteration mineral suites, particularly the phyllosilicate phases, logging was augmented by systematic measurement of spectral data using a Terraspec instrument.Recently the Kisladag spectral database (over 85 000 readings) was reprocessed by the newly developed methodology (aiSIRIS™) that allows relative quantification of the spectrally-responsive minerals. Visualising this transformed spectral mineralogy at various mineral concentration thresholds using implicit modelling software (Leapfrog®) led to the creation of consistent mineralogical and alteration domains that are used for the definition of geotechnical and geometallurgical parameters. An implicit modelling workflow enables these domains to be easily updated as new data is collected while maintaining geological integrity of the model.CITATION:McKinley, S, Baker, T and Öztas, Y, 2017. Alteration at Kisladag gold mine, Turkey – a progressive study in geology, geotechnics and geometallurgy, in Proceedings Tenth International Mining Geology Conference 2017, pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The Purification of Low-Grade Quartz Ore by Flotation and its Mechanism

Sep 13, 2010

More than 100,000 people are expected to be in Las Vegas, NV in March for ConExpo-Con/Agg 2002, the largest exhibit of its kind in the Western Hemisphere. This triennial event features equipment, services and technical sessions geared toward the global construction aggregates and ready mix concrete industries. ConExpo-Con/Agg 2002 will take place March 19-25, 2002 at the Las Vegas Convention Center. For registration information, contact the show offices, phone 800-867-6060, 414-298-4141, or 301-587-3140, Website www.conexpoconagg.com.

Jan 1, 2002