Search Documents

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By William W. Adams

Progress made by the quarrying and related industries of the United States during 1939 included increases in the number of men employed and the number of man-hours worked and reductions in the death and injury rates per million man-hours of exposure to risk. Forty-seven States reported quarries in operation; in each of 26 States the industry employed 1,000 or more men. Of these 26 States, 16 reported lower accident rates than in 1938. Among the operations of various types for which separate figures are published in this bulletin, the limestone, lime, and cement groups reported lower accident rates. During 1939, 79,449 men were employed in the quarrying industries. The period of operation of the plants averaged 236 clays per employee, with a total working time that equaled nearly 144 million man-hours. Accidents at the plants resulted in 48 deaths and 5,204 disabling injuries among the workers. Expressed as frequency rates, the accidents represented 0.33 fatality and 36.18 injuries for each million man-hours of work performed during the year. The major cause of fatal accidents inside the quarries was falls or slides of rock or overburden; nine deaths were reported from this cause. Four men were killed by explosives and four by falls of persons. Nonfatal injuries inside the quarries were clue chiefly to handling materials; about one-sixth of the total number at all operations in connection with quarries and related plants were in this class. Flying objects also caused numerous injuries, although only about one-half as many as did handling materials. Next in numerical importance were injuries from falls of persons. Then followed accidents caused by falls or slides of rock or overburden and accidents caused by machinery.

Jan 1, 1941

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By C McGuire, W Harris, S Arsenault, D Witow, B Rogers

Mining deep orebodies is increasingly becoming the norm as the ‘easy’ orebodies are depleted. Deep ore mining requires significant ventilation and cooling infrastructure to not only meet regulatory requirements for air quality but also to achieve acceptable workplace temperatures with the higher strata rock temperatures and increased auto-compression. At the same time, advances in battery equipment technology are turning the possibility of a battery powered fleet into reality. The switch from a diesel fleet to a battery powered fleet offers several positive opportunities for the design and operation of a deep mine.The potential to reduce ventilation and cooling requirements due to battery powered equipment results in significant cost savings for mine development and infrastructure. Battery powered fleets are not subject to the same dilution requirements associated with diesel fleets thus allowing lower ventilation rates. At the low ventilation volumes possible with a battery powered fleet, surface refrigeration plants are limited with respect to the amount of cooling that can be delivered to the workface. Considerations for calculating the optimum air flow and cooling requirements are presented. Considerations for locating the refrigeration plant are also discussed. This paper presents these opportunities and considerations; including a case study comparing the ventilation and cooling system design with a diesel fleet versus battery fleet for a planned mine in Northern Ontario, Canada.CITATION:Harris, W, Arsenault, S, McGuire, C, Rogers, B and Witow, D, 2017. Diesel to electric – creating a positive paradigm in underground ventilation and cooling, in Proceedings Australian Mine Vent Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

Jan 1, 2006

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.' The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

By K C. Runge, E Tabosa, A Jankovic

Flotation recovery in geometallurgical modelling is usually predicted based on relationships developed from batch flotation testing of different ore types. These batch flotation tests are usually performed at a constant set of operating conditions and at a fixed feed grind size P80. Usually the laboratory feed grind P80 is that which is expected to be produced in the full-scale flotation circuit for that particular ore type.Flotation recovery will be a strong function of the valuable mineral particle size distribution, with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation of this fraction. This valuable mineral particle size distribution is not characterised by the solids P80 parameter alone. The proportion of material in each class will also be a function of the slope of the size distribution and the degree of preferential grinding of the valuable mineral in comparison to the total mass of the ore.This paper will demonstrate (through example) how these other size distribution parameters can change with a change in grinding technology, the size and operating conditions used in a grinding unit and the characteristics of the classification technology used in conjunction with the grinding unit. Case studies will be presented that demonstrate how this can result in these parameters being very different in laboratory testing to that produced in the full-scale comminution circuit. A rule of thumb that laboratory rod milling rather than ball milling produces a size distribution most similar to that of the full-scale grinding circuit will be challenged. These differences can result in a significant change in flotation recovery. It is therefore important to consider these parameters when developing a laboratory geometallurgical program, to enable more accurate prediction of the flotation recoveries that will be achieved in the full-scale process.CITATION:Runge, K C, Tabosa, E and Jankovic, A, 2013. Particle size distribution effects that should be considered when performing flotation geometallurgical testing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 335-344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Ministry of Economic Development has as its slogan æTogether making the differenceÆ. The Ministry is required to work in partnership with the private sector, local authorities, Maori economic entities, trade unions and community groups to transform New Zealand's industrial and economic base. The Government is seeking to achieve sustainable and balanced economic development by: being more actively involved in economic management; working in partnership with the public and private sector and with worker and business interests; focusing on adding value in industries (including primary industries) with long term potential; and bringing the tools of economic policy together in a coordinated way. The Ministry, particularly through its operating group Crown Minerals, is committed to working with industry to achieve mutual goals and to obtain continuing investment in minerals and coal exploration and mining and an active New Zealand minerals industry.

Jan 1, 2000

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

By Oswald J. Heinrich

(with figures on plate V.) THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as men¬tioned below. I am satisfied that the only system of working this thick coal is by cross-cutting ( Querbau, ouvrage à travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Sile¬sia (Königsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregu¬larities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped "troubles" making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ulti¬mately allowed to fill up with water, in order to protect the tipper works in future from fire in the gob below. This I consider indispen¬sable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

Jan 1, 1873

By J Harris, P Kirsch, D Cliff, M Spinks, S Goater, D Sprott

Fires are a common and recurrent unwanted event in the operation of open pit mines. In most cases, the causes of events such as fires are already æknownÆ but are either overlooked or not fully addressed in planning. Ongoing rapid growth of the global mining industry is creating a scarcity of skilled personnel, and high turnover within operations. This contributes to loss of corporate memory in risk management activities. RISKGATE« is an online risk management system designed to support and assist in the analysis of priority unwanted events in Australian coal mining operations. Funded by the Australian Coal Association Research Program (ACARP), RISKGATE« is a knowledge management program that delivers best-practice controls for unwanted events and assists operations in staying abreast of emergent risks and threats. RISKGATE« content has been primarily developed from an association of industry experts, and enriched with input from additional academic and technological resources. In mining operations, RISKGATE« provides a continuum of knowledge and best practice for risk identification, assessment and management. RISKGATE« will assist companies in improving safety performance, operational efficiency, operating practice and training. Here we present the RISKGATE« prototype as developed in 2011 for Fires, with a case study presented for the initiating event Fires on Mobile Plant.CITATION:Harris, J, Sprott, D, Spinks, M, Cliff, D, Goater, S and Kirsch, P, 2012. RISKGATE« - A case study in application to fires on mobile plant, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 49-54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.