Search Documents

By J. A. Finch

"Gas dispersion in flotation defines the efficiency of the process once the chemistry has been established. There are three measurements, superficial gas velocity, gas holdup, and bubble size, which along with the derived quantity bubble surface area flux, are used to define “gas dispersion.” Sensors for measuring gas dispersion in industrial machines have been developed. This communication describes the working principle of the techniques and illustrates their potential to detect problems and to improve the operation of individual cells, banks and circuits. IntroductionFlotation is the most widely used process to separate minerals and is finding increasing application in other chemical and environmental fields. The process exploits natural and induced hydrophobicity to collect selected particles on the surface of a bubble. Once the process chemistry to control hydrophobicity has been established, the efficiency depends on dispersion of air to generate the necessary bubble surface area. Bubble surface area flux, Sb, the interfacial area generated per unit time and unit area of the machine, is emerging as one of the most useful variables to quantify gas dispersion (Gorain et al., 1997, 1998) although not without its critics (Heiskenan et al., 2001).For a bubble population of mean size db at a superficial gas velocity (or rate) Jg, the bubble surface area flux can be derived from geometric considerations (Finch et al., 1999):"

Jan 1, 2002

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By P. Trudel, É. Cabot, L. Cabot

"A modular gold processing unit (MGPU) was designed, installed and operated over an eight-month period by RSW-Béroma at the Granada mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up, as well as exploitation results, including productivity and profitability curves, are given for a small-scale mining operation in comparison with larger ones. IntroductionSmall-scale mining (SSM) is a widespread activity in Africa, Mexico, Central America and South America, where numerous small mineral deposits are exploited manually or by semimechanized methods. On the other hand, SSM is almost absent in Canada, where the mining industry traditionally exploits large deposits, using concentration plants with capacities of many thousands of tonnes per day. However, many small gold (and other metallic or industrial mineral) deposits are known in Canada. Their reserves are too small to justify the cost related to the construction of a standard mill and, if they are remote from a custom milling facility, they remain unexploited. With this in mind, RSW-Béroma has developed the modular gold processing unit (MGPU) that allows the profitable exploitation of small mineral deposits. The MGPU is the perfect tool for SSM and its main advantages are a much lower capital cost than a standard mill and its portability, which makes it easy to transport and reinstall on another site, once the exploitation of a small deposit is terminated. The denomination MGPU will be used hereafter in the text as it was primarily designed for gold deposits, although it must be kept in mind that this portable plant can be adapted to other mineral substances."

Jan 1, 2003

By D Craw

TheSouthern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.   Uplift is greatest in a wedge-shaped region between the Alpine Fault and an associated second-order backthrust system, the Main Divide Fault Zone, approximately 20 km to the east. The Main Divide Fault Zone is segmented into NNE and NE striking faults, which are regionally sub-parallel to the Alpine Fault, but dip northwest in the opposite direction. Reverse oblique-slip on the Main Divide Fault is in an easterly direction, with a greater component of strike-slip movement on the NE trending faults. Elevated topography in the Mt Cook region is related to thrusting of a relatively homoclinal sequence of semi-schistose rocks on top of lower-grade greywacke, which controls the position of the Main Divide. Tectonically induced fluid flow resulted in only minor alteration and hydrothermal mineralisation of fault-rocks in Alpine and Main Divide Faults, and localised deposition of quartz and/or carbonate in the immediate hangingwall.   The wedge between the Alpine and Main Divide Faults is segmented by third-order structures north of the Mount Cook region. A series of right-lateral (-085/700S) and left-lateral (-150/600SW) faults, which are synthetic and antithetic to the Alpine Fault, respectively, developed as a conjugate set during uplift. Fluid-flow in the Southern Alps is controlled by these third-order fault/fracture systems. Cu-Au mineralisation, hydrothermal veins, and surface hot spring activity are localised by third-order fault/fractures and appears to be enhanced where conjugates intersect.

Jan 1, 1995

By Helen S. W. Chow

The use of piled raft foundations for tall buildings has been increasing in this decade as it is an economical alternative to conventional piled foundations. Piled rafts are composite structures comprised of the piles, raft and soil and so soil-structure interaction is important in computing the behaviour of the foundation. In this paper, the behaviour of piled rafts subjected to non-uniform loadings will be examined where the raft is supported by piles of different lengths. Finite layer techniques are used for the analysis of the horizontally layered soils and finite element techniques are used for the analysis of the raft and piles. This method accounts for the soil-structure interaction and the lateral resistance of the soil on the piles and raft. Results provided from the present method are compared with the results of a full 3D finite element analysis.

Jan 1, 2006

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of 160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946

By Pedro Vargas Gálvez

El presente texto señala la metodología de selección del software de mantenimiento respecto a este mismo y a la Planta. Para ello, se detalla las condiciones que deberán considerarse en la Organización de Mantenimiento y la aplicación del Software de Mantenimiento MP2 a una empresa. Asimismo, se presenta el Plan de Implantación, los inconvenientes que se han encontrado así como los resultados obtenidos por la utilización del Software MP2.

May 25, 1998

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

By E. V. Lilford

Equity investors and project sponsors have divergent views about expected or minimum returns that should be generated by a mineral project. Irrespective of their views, the fundamental estimation of the corporate cost of capital remains singularly determinable, with additive components of risk and uncertainty often incorporated in the final analysis. This paper discusses and details the fundamental, numerical determination of the corporate cost of capital.

Jan 1, 2006

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By D. W. Dew

Billiton Process Research has carried out extensive research over the past four years to develop new process technology using bioleaching for extraction of copper and nickel from their sulphide concentrates. Continuous pilot scale and laboratory batch testwork has been carried out with adapted mesophile bacterial cultures at40°C?45°C, moderate thermophile cultures at 50°C?55°C and thermophile cultures at 65°C?85°C. Pilot scale work has demonstrated the commercial viability of mesophile cultures for bioleaching of secondary copper sulphide and nickel sulphide concentrates. Moderate thermophiles offer benefits in terms of reduced cooling requirements for commercial reactors and, in the case of bioleaching of nickel concentrates, some selectivity over bioleaching of pyrite. Continuous pilot scale testwork has shown that thermophiles achieve efficient bioleaching of primary copper sulphide and nickel sulphide concentrates, giving much higher recoveries than achieved by bioleaching with a mesophile or moderate thermophile culture.

Jan 1, 2000

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1 pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007