Search Documents

By Arcy, D&apos Banister

The productive potential of the Nation's principal active and inactive silver mining districts has been evaluated, using 1964 economic conditions and assumed silver prices ranging up to $3 per ounce. On this basis, the United States has an estimated 5 billion ounces of unmined silver, excluding minor byproduct silver in gold deposits. Approximately 3.5 billion ounces are contained in deposits requiring higher silver prices to be economically minable, and about 1.3 billion ounces are in currently operating mines. An analysis of silver consumption trends since 1954 indicates that the free world industrial market will climb to nearly 800 million ounces annually by 1985. U.S. industrial silver consumption has been projected to increase at an annual rate of 4 percent from 1965 to 1985. Average annual increase for the remainder of the free world has been 8.1 percent since 1953; this is expected to level off with an estimated average increase of 5 percent to 1975 and 4 percent from 1976 to 1985. Foreign silver production has, in the past, exceeded consumption, but in 1960 the supply deficit was over 100 million ounces. U.S. production, also traditionally exceeding demand, was suddenly overtaken at the start of World War II. By 1964 the annual deficit, excluding coinage, was over 84 million ounces. World coinage requirements of silver are fast declining and expected to total only 25 million ounces annually by 1985. In fact, coins are already becoming major short-term source of silver to fill the large deficit between industrial demand and current production. The larger, long-term deficit (to 1985, the limit of this study) must be balanced by silver from the hoards and new production from silver deposits. Eventually all of the deficit must be met by new production or silver prices will rise until consumption is greatly curtailed. To balance free world supply and demand, it is estimated that the free world must produce an additional 85 million ounces by 1975 and 375 million ounces by 1985. The estimated proportion expected from U.S. deposits is 17 million ounces by 1975 and 74 million ounces by 1985.

Jan 1, 1969

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By Jason M. Ryan

"Along with recent advances in computer technology have come cost-effective systems desiiedto evaluate fragmentation distributions through digital images of particles. In mining operations andmineral processing plants, important data from these systems is obtained through monitoring sizedistributions at key stages of the comminution process. Blast engineers apply this technology as atool for the validation of empirical fragmentation models so that predicted results are more meaningful."

Jan 1, 1998

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P205 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 &apos;21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By C. Deutsch

Resource estimation for the West Leeville deposit is prepared using a conventional explicit approach. The geologic model is developed using interpretive methods based on visual logging. Grade shells are then prepared at low and high grade cutoffs. The low grade shell includes material of interest (Au > 0.010opt), while the high grade shell is developed slightly below the economic cutoff grade for mining. Grade estimates are made within these boundaries. This paper documents a conditional simulation study to evaluate the uncertainty contributed by both the grade shells and grade estimates. Multiple realizations are generated for the grade shells and the grades. The full combinatorial of realizations are merged to assess the uncertainty and the relative contribution of the grade shell and grades.

Jan 1, 2007

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By J. Wills

The use of drilling rigs to increasingly mechanize stope drilling has been acknowledged as important for the S.A. mining industry in it ís efforts to tackle the challenges of low productivity, AIDS and an ageing driller workforce. The spin-offs of increased safety, cost-effectiveness and better mining performance provide advantages to all?from the driller to the shareholder. However, implementation or product rollout has varied from outright success to dismal failure. A study of various cases by Novatek and Anglogold TDS showed clear reasons for these differences. Whereas the successes were characterized by clear objectives, accountability, user buy-in, a commitment to make the technology work and no-nonsense reporting, these were typically absent in failed implementations. The attitude at unsuccessful mines was to ?trial? the equipment?even subconsciously, a ?trial? is a test where failure becomes an acceptable outcome. During the study it became clear that mining management are not adequately trained to manage the often-tricky rollout process. They are often also not empowered or clearly mandated to deal with the organizational, human and technical issues that must dovetail to create a success. The output of the study was to develop a basic rollout process that could be used to formally manage the implementation of new drilling technology. Creating an alignment between the mine, workforce and supplier promotes a win-win situation that will not otherwise spontaneously arise.

Jan 1, 2002

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By George A. Savanick

An experimental hydraulic jetting device intended to operate in a 16-in-diam borehole was designed, fabricated, and used to cut coal and simulated coal samples. This device consisted of two 0.107-in-diam nozzles that rotated in a plane perpendicuIar to a 50-inch length of high-pressure tubing. Experi¬ments were also conducted with stationary jets issuing from a single 0.142-in-diam nozzle. Numerous experiments were performed using systematic variations of jet parameters coupled with assessments of cutting rates. These Bureau of Mines tests showed that when operated at 4,000 psi pressure and a 40-gpm flow rate (1) the device can fragment coal up to a distance of 8 feet from the nozzle, (2) 4,000-psi jets cut more effectively than lower pressure jets with the same nozzle diameter, (3) stationary jets do not cut as effectively as moving jets, (4) interkerf breaking occurs when the kerf spacing is less than 2 inches, and (5) if the kerfs are spaced <1/2 inch, the jet is deflected and thereby reduces cutting effectiveness.

Jan 1, 1975

By K. Wenrich

The uranium industry has made a dramatic turnaround in the past three years that even the most optimistic economist was not willing to predict during the uranium downswing of the 1990s. Uranium reached a 30-year low in February 2001 of $6.50/lb. By the end of February 2006 it had soared to $38.50/pound. This nearly 600% increase in the uranium spot price within 4 years dwarfed the increase in gold price that has barely mustered a 100% increase. The initial slow rise from $6.50 in February 2001 to $10.75 in April 2003 (fig. 1) was primarily driven by the decrease in the value of the dollar. Since then several factors have contributed to the soaring price: (1) The awakening of many to the simple fact that uranium supply has not met demand for several years and that the world’s stockpiles are being drawn down, (2) How sharply this fragile supply can be impacted by disasters at the world’s major uranium production facilities, such as a) the flooding of the McArthur River Mine in the spring of 2003, b) fires at Olympic Dam, c) the potential that Rossing, with an annual capacity of 4000 tonnes uranium might close by 2007, (3) the withdrawal of Tenex from the HEU (highly enriched uranium) feed agreement, and (4) the announcement by the Chinese of their intent to build 30 new nuclear reactors.

Jan 1, 2007

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By A. D. Prokop, J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated long-wall test facility located at the Pittsburgh Research Center. Sound levels were recorded every 1.5 m [5 fl] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 MA attenuation was attained upwind of the headgate drum.

Feb 24, 1997

By G. E. d’Aquin

Sources of sulfur have varied based on technology and societal needs. It has been mined in its elemental form for centuries. Twentieth century technology brought thermal mining (Frasch, 1894) to the forefront of sulfur extraction. Then, by the 1980s, petroleum processing generated almost 40 percent of the 50 Mt (55million st) of sulfur in all forms (SAF) produced in the world. Metals processing (the reclamation of effluent gas by various means as “sulfur in other forms,” or SOF) followed at 30 percent of all sulfur values produced and then Frasch at 22 percent. Petroleum and gas processing now generate most of the elemental sulfur produced in the world. Single Two Frasch mines remain, one each in Iraq and Poland. Conventional mining of small to insignificant volumes also survives in Russia, Latin America and Indonesia. The volume of “recovered” sulfur (the name commonly given by the industry to hydrocarbon-derived material) generated will increase faster than energy consumption as oil and gas with greater amounts of sulfur are used and environmental restrictions on the sulfur content of the fuel consumed become more stringent.

Jan 1, 2005

By Ioannis K. Kapageridis

The lignite deposits of the Kozani-Ptolemais-Amyntaio basin in western Macedonia (North-West Greece) present a difficult modelling problem. Each deposit consists of several thin lignite layers ranging from a few centimetres to a few tens of centimeters in thickness, and thin intercalated sterile layers of marly limestones, marls, clays, and sands. These layers are practically impossible to model individually due to fast lateral transition of lignite layers to humus clay and vice versa and the lack of reliable and detailed stratigraphic correlation, leading to compositing methods being applied prior to any interpolation and modelling. The complexity of the deposit is further increased by the presence of a number of faults. This paper presents the modelling and estimation procedures applied during the most recent study of the South Western Field ? a new deposit that is considered for development and lignite production over the next years and will support the operation of a new power station in the area. Special focus is given to drillhole database structuring, fault modelling, stratigraphic correlation, mineable lignite intervals compositing, and resource estimation. The use of specialised mine planning software in all stages of modelling and estimation is thoroughly explained.

Oct 1, 2009