Search Documents

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By Marilyn Biviano

(l)The direct economic costs to this nation resulting from a decision to embargo South African strategic and critical minerals imports are estimated at $1.85 billion per year.2,3 About 94 percent of these estimated costs are for two platinum-group metals (PGM's), platinum and rhodium. The estimated costs of a 5-year embargo beginning in 1988 for the strategic and critical minerals analyzed are presented in Table 1.4 (2)There are sufficient alternative world sources to South Africa for manganese, chromium, palladium, titanium, and vanadium to meet U.S. industrial demand in the event of an embargo. (3)Alternative world sources to South Africa for platinum and rhodium cannot meet U.S. industrial demand. Non-South African world supply sources can meet about 40 percent of domestic platinum consumption requirements and 50 percent of rhodium requirements. (4)As a result of the increase in prices for platinum and rhodium during the embargo, expansion of domestic platinum-group metals mining and secondary production is expected. During a five year embargo, domestic primary and secondary production expand and together satisfy about one-third of U.S. platinum requirements, one-third of U.S. rhodium requirements, and over one-half of domestic palladium requirements.

Jan 1, 1988

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

Large scale fluid extraction from the Latrobe Group in the Gippsland Basin is occurring as a result of offshore petroleum production and coal mine dewatering in the Latrobe Valley. Groundwater extraction in the Latrobe Valley exceeds recharge and is causing an expanding area of declining hydraulic head in the Latrobe Group, and regional land subsidence which is well documented. Recently the government water sector completed the installation of a network of Latrobe Group monitoring bores in the remainder of the onshore part of the Gippsland Basin. The bores situated along the coastal area show a steady decline in hydraulic head of about 1 m/year which can be attributed mainly to petroleum production.

Jan 1, 1992

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978--September 30, 1979) under its Nine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By P. H. Morris

The exponential delta profile equation matches the profiles of a wide range of coal and metalliferous subaerial tailings deltas well, but the original model implies unrepresentatively low solids concentrations. A revision, based on analysis of the governing equations of mobile bed flows with high concentration values, has shown that for exponential delta profiles to form there must be quasi-steady, slowly varying flow and slow deposition as well as tailings with a log-uniform sorting-parameter distribution. Deposition on tailings deltas is slow and the flow in many natural streams and, by analogy, tailings deltas is quasi-steady and slowly varying; the assumption of such flow is justified by the strong congruence of the revised model and the available data. The predictions of the theoretical model are essentially unchanged but concentration and flow Froude number are now not explicitly limited

Jun 19, 1905

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By T F. Guerin

Explorationn and mining have shown to cause significant impacts to the terrestrial and marine environment. Current mining and exploration techniques are outlined in the light of their potential to impact upon the environment, ie negligibly, negatively or positively. A profile of five Australian-based gold producers is presented. The development of protocols to specifically deal with the highly regulated and ever changing, mining and environmental legislation. demonstrates mining companies can successfully opcrationalise the concept of sustainable development.

Jan 1, 1992

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By A. L. Marshall, F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C.oin a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. APPARATUS AND TECHNIQUE The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 0800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard' glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not 'a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by

Jan 1, 1944

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By Thomas J. Albin

U.S. Bureau of Mines research has found that maintenance of surface mining equipment is involved in slightly more than one-third (34.1 pct) of all surface mining accidents. Two groups of machines, haulage trucks and power shovels, accounted for over one-half of all surface mining mobile equipment maintenance accidents in 1978-84. Maintenance work-time histories for these machines were compared with accident records to identify the most hazardous-to-maintain systems within the machines. Recommendations to reduce the accident risk associated with maintenance of these hazardous systems are presented.

Jan 1, 1990

By Bruce Geller

The 2005 Prospectors and Developers Association of Canada (PDAC) convention continued the upbeat mood found in 2004. The global mining industry is booming due to higher commodity prices in nearly every sector. Other factors include low commodity inventories, China’s strong resource demands, the weak U.S. dollar, the very strong Euro, global uncertainties, an almost overripe investment climate for natural resources and the highest mining exploration budgets in seven years. Even unglamorous commodities, like iron, uranium and zinc, received copious attention in talks, the investors’ exchange, the core shack and in certain hospitality suites. The following impressions were gathered at the convention and enhanced by conference handouts and some abstracts that are available on the PDAC’s Web site, www.pdac.ca. At least 119 papers were presented, almost twice last year’s number.

Jan 1, 2005