Search Documents

By Rodney Hundermark, July Ndlovu, Lloyd Nelson, Phillimon Mukumbe, Paul van Manen, Whitey Seyanund, Bart Pieterse, Bertus de Villiers, Diale Mokwena

The 2003 redoubling in power to 68MW on the Polokwane Smelter furnace represented a significant intensification in platinum group metal (PGM) smelting. Combined with onerous ‘green’ PGM concentrate smelting requirements, this yielded conditions unusually corrosive to copper coolers and refractories. This presented unexpected operational and design challenges to reliable crucible operation and maintenance. Combined with specific operational control intervention, development of protective coatings has led to the life of water-cooled copper components improving from 9 to 40 months. The furnace matte endwall was extended in 2010 to address accelerated wear of refractories and the potential risk for contact of copper components by superheated matte. An 18 month planned endwall rebuild cycle has been demonstrated (versus catastrophic failure within 9 months). Finally, benefits including lower energy consumption, improved metal recoveries and higher productivity resulting from operational and in-house design developments will be described, that justify “Celebrating the Mega-scale” in PGM smelting.

Jan 1, 2014

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Freddy Syvertsen

"During the past two years the Association of Norwegian Foundries in Norway has been running a project in evaluation of CAD/CAM systems for foundries.In this work we have had a closer look to the various steps from drawings to the finished castings. On this background we have made a specification of the special needs in the foundry process. The main content of this paper is a presentation of this specification.Some CAD/CAM sytems have been compared with the specification and a summary of the result is presented.In the project we have also had a closer look at some systems where we actually have tried the user interface and some of the possibilities in the systems. In this way we have gained a more detailed knowledge of the systems and we have also got some experience in NC-machining from the systems.IntroductionThe development of CAD/CAM systems has taken place with almost no interaction with the foundry business. This becomes clear when you are having a closer look at the systems. Most of them have not the possibility to describe the complex sculptured surfaces that is often found on castings. The people developing the software, have paid little or no attention to the problems arising when a geometry is going to be transformed for the casting process. Among the problems are the decision of where to place the parting line and to adjust the draft angle. These problems must be solved properly to be able to withdraw the model from the sandmould. In die casting the problems must be solved to be able to get the casting out of the die.In Norway some companies have been developing CAD/CAM systems for several years, with limited interest in foundry problems till 1983. To present the special foundry problems to them a specification of the needs was made that year. Another reason for making this specification, was to compare it with the CAD/CAM systems on the market (1).Design of castingsGeometry transferThe foundries in Norway are small units with almost no design of their own casting products. They are subcontractors receiving paper drawings and limited informations about the product from the mechanical industry both in Norway and in other European countries. This is going to change, and in the future the geometry will be transferred by magnetic tape or by a network of computers."

Jan 1, 1986

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By M. C. Flemings, S. B. Brown

"Metallurgy, as all of material science and engineering, rests on the intellectual foundations of processing-structure-property-performance relationships. Today it is widely recognized that processing has been too long neglected and presents exciting opportunities for exploitation. New processes, many of them already in the laboratory, will be exploited in the year 2000 and beyond, for near net shape forming and for achieving-new metallurgical structures and composite structures. Process modelling will alter the way we think about process and product design. Processes themselves will increasingly be automated and controlled by computers, altering the nature of the workplace and the tasks of the metallurgical engineer of the future. IntroductionInnovations in metal processing is hardly a new phenomenon, with the field thousands of years old. Nonetheless, the next few decades offer particularly important opportunities to improve our ability to process these materials. We appreciate today the variety of processing paths available to us, including vapor-, plasma- and electro-deposition, multiple phase and casting technologies, and non-equilibrium processes, and how these affect structure at the atomic level and at higher levels of aggregation. We understand the basic physical mechanisms involved far better than even before and have remarkable new abilities to predict, control, and simulate the kinetics underlying processes, and the processes themselves.The following sections describe these new opportunities in greater detail. First, we examine developments in the modelling of metal processing. We then consider some implications associated with process control and automation. Finally we present what we consider to be particularly promising metal processing technologies, and conclude with a few summary comments."

Jan 1, 1988

By Travis Knight

Mixed uranium and refractory metal carbide systems have been proposed for space nuclear power and propulsion applications. Solid-core space nuclear reactors could be utilized for low- earth-orbit (LEO) to geosynchronous-earth-orbit (GEO) transfers, manned missions to the moon or mars, and orbiter missions to the outer planets. However, these high performance space nuclear reactors present some challenging materials engineering requirements for operating in a high temperature, high radiation, and hot hydrogen environment. Since the RoverNERVA programs were concluded in 1973, significant advances in ultrahigh temperature materials technology have been made which can be applied to the development of an advanced solid-core nuclear fuel. Nuclear thermal propulsion (NTP) was first studied in the U.S. beginning in the mid-1950's during the RoverNERVA programs. During that time, about 20 rocket reactors were built and tested. More recently, Russian nuclear rocket reactor tests with pseudo-ternary carbide nuclear fuels (U, Zr, Nb)C and (U, Zr, Ta)C have been operated at temperatures as high as 3300 K for one hour. This study examined the processing parameters for fabricating the pseudo-ternary carbide, (U, Zr, Nb)C.

Jan 1, 1999

By G. C. Yao

Branch and needle-shaped intermctallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallie compound particlcs may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermctallie compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "C" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25>< 15" 130mm3 with a lateral baffle inside. The separator was put into the interspace of the "C" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhanees signifieantly the efficiency of impurity separation.

Jan 1, 2003

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. [n 1996, however, it successfully shifted to a single fumace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This &apos; paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

By James C. Sever

Two green field magnesium reduction plants are under consideration using dolomite as the raw material. The Calix calciner was independently selected for both plants. The unique design of this calciner is detailed and the advantages defined for the specific application. The low carbon foot print of this unit combined with the ability to capture food grade carbon dioxide makes this an environmentally proactive approach to carboniferous ore calcination.

Jan 1, 2015

By I. D. Reznik

The flowsheets of converter matte production from sulphide copper - nickel and oxide nickel ores on Severonickel and Yuzhuralnickel integrated ,;corks are given. The cobalt behaviour in electrosmelting and autogenous ore smelting, converting and converter slag cleaning is observed. A list of acticles published in the 80 th is given.

Jan 1, 1993

By Baokuan Li, Fang Wang

"Comparing with the single electrode in electroslag remelting processes, two series-connected electrodes have the advantage of little inductance, lower power consumption and higher melting rate, which was widely used to produce superalloys and specialty steels. Detailed understanding of the electromagnetic field distribution is essential for both improving ingot quality and saving electric energy. In the present work, a 3D finite element model was developed for the magnetic field, electromagnetic force, current density and Joule heating field of electro slag remelting processes (electrode, slag and ingot) with two series-connected electrodes using Maxwell equation, Lorentz law and Joule law. The results show that the maximum current distribute occur at the middle of electrode, due to the interaction of selfinduced and mutual-induced of two series-connected electrode; associated magnetic flux density on the inner side of electrode increase and the outer decrease; The maximum joule heating is at the interface of slag and electrode. The parameter study shows that if the current frequency is greater than 35Hz, the current density in inner electrode tend to linear distribution; with the increasing of original current, The maximum current density near the wall in electrode will increase linearly; with the increasing of electrode innnersion depth and decrease of slag cap thickness and the maximum of the joule heat in slag will increase.IntroductionElectroslag remelting processes(ESR) are widely used to produce superalloys and specialty steels [l-3l_Two pair, four pair or six pair electrodes in electroslag remelting processes is common in casting large scale ingot, which has the advantage of little inductance, lower power consumption and higher melting rate, comparing to singe electrode. They have the same essence with two electrodes in ESR.Compared to the single electrode ofESR, the other electrode is added which can decrease the reactive resistance and power consumption in the two electrodes of ESR. It is a complicated metallurgy process with a series physical and chemistry phenomenon from the molten of steel to the solidification of ingot [4-71_ These physical and chemistry phenomenon originated the effect of alternating current of high intensity. The rule of the alternating current of high intensity which revealed the law of physical and chemistry phenomenon in ESR is the precondition of improving ingot quality and saving electric energy. Jihe Wei and Yongli Ren[S-9lstudied the distribution of electromagnetic field in single electrode ofESR with Maxwell equation and relative electromagnetic theory. It had the limitation that take the electrode and mold as infinite conductivity. A detail analysis of Electromagnetic fields in ESR had been conducted by Patel A D [JO-llJ using general stream-function formulation. It is difficult to extend to three dimensions which could not be used widely. Daniel V [lZJ and Kharicha A [BJ only analysis the current density associated magnetic flux density field and temperature field without the whole irlformation of electromagnetic field. Maopeng Geng [l4J considered the current density and temperature field of the real and fake electrodes in ESR without skin effect. As to the complication of the two electrodes of ESR, it is rarely reported the electromagnetic field and Joule heating field of the two electrodes in ESR. The rule of effect of electromagnetic and modification of numerical simulation should be studied in depth."

Jan 1, 2011

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

By Florian Kongoli

Converters have been playing an important role in the extraction and processing of metals ever since the first type of converter was invented about 100 years ago. Historically their operation has been mainly based on the experience of talented operators rather than on strict control and optimization technologies. However, in the new realities of unavoidable necessity to increase productivity and in the conditions of diversification of primary materials from various geographical areas, improving control and optimization techniques have become indispensable. In this paper a review of the authors? previous work in terms of improving control and optimization of converter operational practices related to magnetite content and precipitation, slag and metal blows, problematic and dangerous elements such as As, Sb etc. has been described by highlighting the advantages that the new control and optimization methods and tools bring to everyday converter practices. Several examples are given and future work is underlined

Jan 1, 2005

By Zhao Hengxian

We studied the phase diagram of Na3AlFe-ZrO system, reduction of ZrO2 by aluminium and electrochemical behaviours of ZrO2 in the system. The results show that Na3ALF6-ZrO2 system is a simle eutectic one, that the velocity of reduction of ZrO2 in the system is rapid al 960&apos;C and that the Zr content in the alloy abtained can reach as high as 2.5wt%. Potential scanning shows that there exist new current peaks on the potential scanning plats except for the cuurent peaks corresponding to the oxidation of aluminium. The method of making Al-Zr alloy in our paper has advantages over the traditional method of mixing metals.

Jan 1, 1992