Search Documents

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By A. G. Jackson, S. J. P. Laube

"Control of thin films during the growth process is dependent on several parameters that are difficult to monitor, including flux of film material, pressure, substrate temperature, composition, and thickness. One means for easing this difficulty is to take advantage of emission spectra associated with the process and the film. For pulsed laser deposition (PLD), the ion cloud generated by the laser has characteristic emission spectra that can be used to control the flux and, hence, the film. For chemical vapor deposition, the species present can be determined using mass spectroscopy and specific peaks can be used to control the deposition. Raman spectroscopy affords the possibility of real-time control by sensing characteristic peaks associated with film composition and thickness. These spectroscopic methods offer a real-time alternative to process control that is very attractive, because of the ability to accurately control films to achieve the engineered structures and properties sought. Examples are presented to illustrate the capabilities of these methods for thin film preparation.IntroductionThe drive to reduce costs and improve efficiencies of operation sets the tone for much of research, basic or applied. Basic research is limited by the ability of sensors and associated instrumentation to measure parameters accurately and reproducibly. Applied research has the same limitations and also the added constraints of time and costs. Hence, there are strong incentives to explore means for refining existing sensors with respect to performance and cost, as well as finding new sensors and techniques for more accurately and rapidly measuring quantities of interest in experiments and in various processes."

Jan 1, 1997

By Deepak Gupta, R. Kageyamat, J. W. Evans

"In electromagnetic casting, a liquid metal pool is partly supported by electromagnetic forces resulting from the interaction between induced currents and an alternating magnetic field. Stability of the metal surface is of paramount importance if the cast ingot is to be free from surface defects. Prior work by Garnier and Moreau had suggested that the magnetic field has no influence on the surface stability, but a more complete analysis at Berkeley suggested that surface perturbations are destabilized by the magnetic field once a critical magnetic field is exceeded. More recently we have employed a modified version of the software SOLA to compute the behaviour of a melt surface in the presence of an alternating field. The computed results support the theoretical analysis in predicting an unstable surface. Experimental work is now in progress to examine the stability of a mercury pool in the presence of an alternating field. Introduction and Previous InvestigationsElectromagnetic casting (EMC) is a technique widely employed in the aluminum industry to produce ingot for subsequent rolling. It is a ""continuous"" casting technique (illustrated in Fig. 1) producing ingots several meters high (and perhaps 1m by 2m in horizontal dimensions) at a casting speed of one or two mm. per second. The technology has gained acceptance because the metal is solidified without contact with a mold. Consequently the surface finish of the ingot is usually smooth and the ingot can be fed directly to rolling without machining, the surface (""scalping""). Scalping is necessary with alternative technologies (e.g., DC casting) where a mold is used. Consequently any disturbances that result in surface imperfections of EMC ingot are a serious matter. One type of imperfection is waviness on the surface of the ingot; a line drawn along the crest of a wave would run horizontally around the ingot. This imperfection may be caused by waves on the surface of the metal pool. As the waves reach the solidification line at the periphery of the metal they cause alternate outward and inward bowing of the meniscus at that point with attendant small (but significant) changes in ingot width. Elimination of building vibrations and similar disturbances minimize the occurrence of these surface waves but it is interesting to speculate whether there are disturbances of the metal pool that arise from the electromagnetic forces supporting the liquid metal. These forces are generated by the interaction of currents induced in the melt and the magnetic field produced by the current imposed on the inductor surrounding the melt. The present investigation has been concerned with whether the alternating magnetic field destabilizes the melt surface."

Jan 1, 1994

By K. Adham

"Fluidized beds are utilized in a wide range of high-temperature applications throughout the metals and materials industry. Their main advantage is the fast and uniform heat and mass transfer between the hot combustion gases and the particulate solid feed. A further benefit can be the lowering of the processing plant's energy consumption, through heat recovery from the fluid bed processes used for solids heating. Here, the enhanced energy efficiency of fluidized systems is investigated and the modeling results are discussed for three configurations: the flash tube, the single bubbling bed and the multi-stage fluid bed. Key thermal design aspects of each system are identified based on results from process simulations, in order to benchmark their main operating features and overall energy efficiency. Suitability and applicability of each configuration is also discussed based on a number of process and material property considerations.IntroductionCombustion based heating of particulate solids is commonly done using three different types of fluidized beds. The flash tube (FT) is similar to a hot pneumatic transport system. The single-stage fluidized bed (FB) typically uses in-bed combustion. The multi-stage fluidized bed (MSFB) can have two or more stages stacked into a tower.Flash tube (FT) suspends the incoming solid charge in a high-velocity stream of hot combustion gases. To maintain the solids suspension in the FT, two parameters are required: high velocity for elutriation of the particles and adequate solid-to-gas ratio for avoiding high pressure drops and solids drop-out [l].The fluid bed (FB) works at much lower velocities than the flash tube. Therefore, most of the solids are not conveyed in the gas stream, but are only suspended in a liquid-like manner. At minimum fluidization velocity (Umr), the gas flow exerts just enough force on the solids to keep them suspended in place [2].Multi-stage fluid bed (MSFB) heats up the solids as they are transferred from an upper bed level to a lower one, counter-current to the rising flow of hot gases generated at the lowest stage. As the temperature and volumetric flow of the gases decrease from bottom to the top stage, smaller bed diameters can be used in the energy recovery stages [3]."

Jan 1, 2014

By Christian Wögerer

For material or process development as well as for quality checking of materials, thermal diffusivity measurement may be the tool of choice in many applications. Especially if diffusivity is measured locally resolved, a lot of information can be read out of such a ?diffusivity image?. This paper explains the method to measure coplanar specimen like plates and lists some interpretations of diffusivity images, like inhomogeneity of sintered materials, structural voids or inclusions. Diffusivity is a material property, describing transportation of heat in solids in spatial and temporal terms. With thermo cameras it is possible, to measure diffusivity of larger areas simultaneously. The result is an area of diffusivity values that may be plotted or displayed like an image. Locations with lower diffusivity values could be caused by the presents of structural differences in the material, by decomposition of the material components or by inclusions of other material like air.

Jan 1, 2009

By T. T. Chen

Secondary copper anodes are generally rich in Sn, Pb, Ni and Sb, but are notably deficient in Se, Te and Ag. In the secondary copper anodes, most of the Ni, virtually all of the Ag, slightly more than one-fifth of the Pb, about one-third of the As and Sb, and approximately one-tenth of the Sn are in solid solution in the copper. The remaining impurity contents occur as 1-5 µm grain-boundary inclusions in the anodes, and these are mainly Cu2O, SnO2, Cu-Pb-As-Sb-Bi oxide, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide, Cu-Sb-Ni oxide (Kupferglimmer) and trace Cu2(Se,Te). Barium sulphate, which originates from the mold wash used in casting, is also present in the anodes. During electrorefining, the BaSO4, SnO2, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide and Cu- Sb-Ni oxide inclusions are liberated and accumulate in the slimes layer. Solid solution Ni dissolves and the Ni accumulates in the electrolyte. Solid solution Sn and Pb dissolve, but partly reprecipitate as Sn arsenate and PbSO4, respectively. Solid solution Ag dissolves but rapidly reacts to form Ag2(Se,Te), Ag powder, Ag-bearing Cu2O, (Cu,Ag)SO4 or a complex oxidate phase. Partial dissolution of the Cu-Pb-As-Sb-Bi oxide particles takes place; the Pb component is converted to PbSO4, whereas Cu, As, Sb and Bi dissolve. The reacted particles retain the morphology of the original Cu-Pb-As- Sb-Bi oxide phase. Some of the solubilized As, Sb and Bi remains in solution, but much reprecipitates as SbAsO4, As-Sb-Bi oxide, and as a poorly defined oxidate phase which consists mostly of Cu-Ag-Pb arsenate-sulphate. The high Sn contents of secondary copper anodes do not seem to affect the behaviour of the anodes during electrorefining.

Jan 1, 1999

By C. M. Wai

"Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ che1ation-supercritical fluid extraction technique offers several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, B-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.IntroductionSupercritical fluid extraction (SFE) offers several advantages over conventional solvent extraction including the minimization of organic liquid waste generation and exposure of personnel to organic vapors.[1] The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties which make supercritical fluids excellent candidates for extraction and recovery of organic compounds from solid materials [2] Carbon dioxide is a gas of choice for SFE because of its moderate critical constants (Tc = 31 °·C and Pc = 73 atm), inertness, and availability in purified form. After extraction, the fluid phase is depressurized to separate organic solutes from CO2 gas and the gas can be recycled for repeated use. The SFE technology has been applied to industrial scale operations such as the preparation of decaffeinated coffee and hop extracts."

Jan 1, 1996

An iridium oxide coated titanium electrode was tested as anode in copper electrowinning. Initial results confmed that the DSA-type anode was significantly more active for oxygen evolution than traditional lead anodes. However, during longer runs, the anode potential was observed to increase linearly at a rate of 220 mV/year. Scanning elecuon microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the anode passivation could be attributed to elecuochemical dissolution of the coating. The effect on the anode potential of organic additives (glue and thiourea) and lead in solution was also examined. A preliminary economic evaluation of the anodes is given.

Jan 1, 1992

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Jasper Kwong

The recycling of MgO-C refractories as a slag conditioner in EAF (electrical arc furnace) foaming slags have been evaluated by the Albany Research Center. The amount of MgO in the slags is critical for the foaming quality. Good foaming slags provide the benefits of high energy efficiency and low refractory consumption and require saturation with MgO. A computer model predicting the chemistry of MgO saturated foaming slags was designed to predict suitable amounts of MgO additives from MgO-C spent refractories. This model can also help to reduce the amount of slags and to improve the economics of producing steel. The implementation of this recycling program is underway at steel plants and the experience of recycling spent refractories will be discussed.

Jan 1, 2002

By Lauri E. K. Holappa

Ferrochrome, as the central constituent in stainless steels is one of the most rapidly growing primary metallic products. In this contribution results of a comprehensive study on the reduction process of chromite ore to FeCr are presented including thermodynamic examination, experimental work on kinetics and mechanisms in solid state, and smelting reduction conditions as well as kinetic modelling of solid state reduction.

Jan 1, 1999