Search Documents

By Joel Nonnweiler, David Young, John Hawley

The Sacramento Regional County Sanitation District has implemented a billion-dollar interceptor system master plan, including the 31 km (19 mile) long Lower Northwest Interceptor (LNWI). For the two LNWI Sacramento River crossings, pipe-jack/micro tunnel drives in excess of 300 meters (1,000 ft) from 30 meter (100 ft) deep shafts in mixed soil conditions below the water table were considered, as were600 meter (2,000 ft) tunnel drives utilizing pressurized-face tunnel boring machines. Operation and maintenance concerns, predicted flood scour, and levee concerns are discussed. A risk assessment process was used to select both profile and construction method. Construction will begin in mid 2004.

Jan 1, 2003

By Peter T. Luckie, Joseph W. III Leonard

INTRODUCTION In a bed of fine coal, water can be found in the interstices created by the particle surfaces and in the pores within the coal particles. The extent of the interstices voidage is obviously a function of the particle sizes and morphologies, as shown by the fact that the bulk density of coarse coal is greater than that of fine coal. After drainage, the voids can be completely or partially filled. By increasing the suction pressure across the bed, as is done in vacuum filtering, the quantity of water in the voids can be reduced. But eventually the increased suction pressure has little influence on the moisture reduction. In addition, the moisture in the pore structure of the coal is unaffected by the mechanical removal of the moisture in the interstices. When this condition is reached, the total moisture content of the coal can only be reduced further by evaporating the water. Evaporative drying is done for one or more of the following reasons: 1. To avoid freezing difficulties and to facilitate handling during shipment, storage, and transfer to the points of utilization. 2. To reduce the heat loss due to evaporation of the moisture from the coal during the combustion process, thus increasing heating efficiency. 3. To decrease transportation costs. The heating value of coal is equally improved for each percentage point reduction in the noncombustibles in coal. It is estimated that a reduction of 1%22 in the total moisture in the coal increases the thermal efficiency of the heat-raising process by about 0. Some coal buyers consider 1 % moisture content to be the equivalent of a 4% ash content.23 It is important to avoid drying the coal to too low a moisture level, since the complete removal of surface moisture to produce a bone dry product can result in a serious dust, wind lost, and safety problem. Surface moisture con- tents of 3% or less for shipped coal are not uncommon. However, the evaporatively dried coal may be lower, Y, to 1%, since the mechanically dewatered coal may be higher. Evaporatively dried coal can be treated (sprayed) with chemicals in order to control the dustiness and any freezing difficulties, thereby providing the producer with more operational flexibility. The evaporative drying of coal is essentially a process of simultaneous transfer of energy, usually in the form of heat, and water, in the form of vapor, from the coal. In order to remove the undesired moisture, it is necessary to raise the temperature of the water from the entering temperature of the feed stream, TF, to the boiling point of the water (usually taken as 212"F), vaporize

Jan 1, 1991

By Taehong Kim, Changsoo (Kevin) Moon, Anil Parikh

"This paper presents an overview and performance evaluation for a reconditioned decades aged open type hard rock TBM utilized for the twin running tunnel excavations of the Second Avenue Subway Project in Manhattan, New York. The TBM tunnel lengths are approximately 2,370 m (7,800 ft, east TBM Tunnel) and 2,190 m (7,200 ft, west TBM Tunnel) with a 6.7 m (22 ft) bored diameter. This “senior” TBM mined through metamorphic rocks consisting of schist, granofels, and pegmatite, and encountered various adverse geological structures, including some relatively heavy groundwater inflows. The ground support was generally pattern friction rock bolts, and steel sets were used in poor ground. This paper presents TBM characteristics and the subsequent performance, such as machine utilization, downtime, cutter consumption rate, net penetration rate, and daily advance rate. Machine operating parameters including thrust, torque, gripping force, and cutterhead RPM, are compared with various accompanying ground conditions. The performance changes between the adjacent tunnel sections are also presented. INTRODUCTION Project Overview The Metropolitan Transportation Authority Capital Construction (MTACC)’s Second Avenue Subway (SAS) Program consists of four (4) phases from 125th Street to Manhattan Battery Park along the 2nd Avenue (see Figure 1) in Manhattan New York. As a part of Phase 1, Contract 1 was awarded to S3 JV (Skanska/Schiavone/Shea) to build a TBM launch box and subsequent twin TBM tunnels from 92nd Street to 63rd Street under 2nd Avenue. Contract 1 was one of the key contracts in Phase 1 to pre-excavate through the footprint of the follow-on underground stations (72nd St. Station, 86th St. Station, and 96th St. Station) by hard rock TBM excavation. The project team included Client MTACC, S3 Tunnel Constructors, Designer, Aecom-Arup JV, and Consultant Construction Manager, Parsons Brinckerhoff. The major elements of Contract 1 included construction of TBM Launch Box supported by secant pile and slurry walls and mining of twin TBM tunnels with a combined tunnel length of approximately 4,560 m (15,000 ft). The dimension of the TBM launch box was approximately 247 m (810 ft) long from 92nd Street to 95th Street, 21 m (70 ft) to 24 m (80ft) wide along the 2nd Avenue, and 18 m (60 ft) to 21 m (70 ft) deep from the ground surface. The launch box was later used for the follow-on 96th Street Station."

Jan 1, 2016

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013

By Byron C. Hardinge, Michael Sokaski, Paul F. Sands, W. Loring III Mc Morris, David J. Akers

INTRODUCTION In the early days of coarse-coal cleaning by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken the loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War II in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-tph (13.6 t/h) pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London.51 In April 1945, operation of this pilot plant was observed by H. F. Yancey, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was immediately started by the US Bureau of Mines (USBM). This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals were made available.52 Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are easy to clean and respond well to simpler cleaning processes, the first cyclone plant was not built until 1961.53 THEORY Before discussing the theory of a dense-medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in Fig.7-51 a mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vortical flow. The refuse moves along the wall of the cyclone and is discharged through the underflow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the overflow orifice, or vortex finder, to the overflow chamber. Washed coal is discharged from this chamber, usually through a tangential outlet.

Jan 1, 1991

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By Alan S. Peck

Chemisorbed oleate films on the surfaces of fluorite, barite, and calcite were studied by means of infrared spectrophotometry. Evidence is presented which indicates the mineral anions, i.e., fluoride, sulfate, and carbonate, are displaced from the mineral surfaces as a result of the adsorption from aqueous solutions. Also, chemisorption reactions between oleic acid and fluorite or calcite occurred spontaneously in the absence of water. Carbon dioxide was identified as a reaction product when dry calcite was contacted with oleic acid. There was no evidence of reaction between oleic acid and barite in the absence of water.

Jan 1, 1964

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By Nicholas Kyriazia, John P. Shubilla

A performance study of oxygen self-rescuers of varying durations from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested on a Breathing and Metabolic Simulator in the Life Support laboratories of the Bureau's Pitts- burgh Research Center. Parameters monitored during the testing were inhaled levels of C02, 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60-min man-test 4, as described in 30 CFR 11H. Results presented include apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1986

By R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are ad¬sorbed on the mineral surfaces. According to infrared spectra showing the reaction to form these compounds, the ratio of cuprous ethyl xanthate to ethyl dixanthogen adsorbed is directly related to pH of the flotation solution.

Jan 1, 1967

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By R. J. Clements

The waterway transportation system in the united states consists primarily of the Mississippi river system. With its navigable tributaries, it is 12,500 miles long. This system naturally accesses about 40 percent of the nation. With its connecting railroads and highways, the river system accesses the united states from the Appalachian mountains in the east to the rocky mountains in the west. Within this area is the vast majority of our agricultural, industrial and material resources.

Jan 1, 1984

By Harry R. Dahlberg

Heap leaching is discussed as a unit process. Five factors are identified as the principal elements that can be measured and/or controlled. These are: 1. Material Size 2. Volume of solution 3. Tonnage of heap 4. Time 5. Solution concentretion. The Rate of Extraction Curves obtained from an actual heap or column tests describes the economic viability of the unit process. By analysis of these curves and the five factors end their inter-relationship it is possible to determine how the extraction rate can be increased. The practice of leach and rest used by many operators is analyzed and shown on a hypothetical rate of extraction curve. The influence of the driving force of the hydrogen ion and ferric Lon as Lixivants and its effect on the rate of extraction curve is discussed.

Jan 1, 1979

By Timothy Batchler, Khaled Mohamed, Morgan Sears

The National Institute for Occupational Safety and Health (NIOSH) initiated a testing program to assess the effects of lateral loading on various standing supports used in underground coal mines. This study is not intended to endorse a particular type of standing supports nor to provide a comparison between different types of standing supports. This paper aims to measure the lateral loading capacity of two types of standing supports and evaluate how it affects their vertical loading capacity and yielding mechanisms. The study utilizes the Mine Roof Simulator (MRS) at NIOSH Pittsburgh. Type-1 support is characterized by telescopic tubes made from ASTM A-513 steel with a specified locking mechanism, and Type-2 support comprises a single component constructed from ASTM A500 Welded Grade C pipe. Vertical load tests were carried out to assess the designed performance of Type-1 and Type-2 props. Type-1 props demonstrated a "constant yielding" behavior, achieving an ultimate capacity of up to 140 kips. Type-2 props showed a "load shedding" behavior, reaching peak verti- cal loads of up to 191 kips. Buckling analysis revealed that Type-1 props were not designed to buckle, and Type-2 props failed due to buck- ling rather than material yielding. Under vertical pre-loading, lateral loading tests showed that Type-1 props can withstand about 9 kips, and Type-2 props can withstand about 10.79 kips of lateral load. This represents roughly 6% of their vertical loading capacities. Testing props under lateral loads in addition to their intended vertical loads showed that the lateral loads could influence their loading mechanisms. Type-1 props did not exhibit the expected "constant yielding" behavior under lateral load but instead showed "load shedding" decreasing their rated vertical capacity by 70%. At high vertical pre-loading, Type-2 props demonstrated "constant yielding" behavior instead of the anticipated "load shedding," leading to a 60% reduction in their rated vertical capacity. These findings provide valuable insights into the behavior of these props under different loading conditions, aiding in their efficient use and design in underground mining operations.

Jun 25, 2024

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959