Search Documents

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By Preusse. Axel

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By Richard H. De Voto

The Pb-Zn-Ag deposits within the Lower and Middle Paleozoic strata of central Colorado (Leadville, Gilman, Aspen, and others) occur principally in Late Mississippian karst-solution features within dolomites and, to a lesser extent, limestones. Several un- conformities within the Devonian and Mississippian carbonate rocks and the subregional dolomitization of the Leadville (Mississippian) Formation that occurred during the Late Mississippian resulted from recurrent uplift of elements of the Ancestral Sawatch, Gore, and Front Range areas within central Colorado. Uplift of these areas also strongly influenced the details of the extensive karst topography that developed during the Late Mississippian. In particular, uplift of the Sawatch Range area caused paleovalleys from 300-600 ft deep to form on the karst landscape. The pattern of karst-solution caverns, sinkholes, cutters, channelways, and breccia-rubble zones was strongly controlled by incision of surface drainages and the strong northeast-trending Mississippian joint system. These subterranean karst-solution features and breccia-rubble soil [ ] zones are the primary controls of the location of the Pb-Zn-Ag ore deposits in these rocks. In the Leadville and Aspen districts, the deeply incised paleovalleys occur immediately adjacent to the principal areas of mineralization. Pennsylvanian deposition of a thick terrigenous and evaporite sequence occurred within central Colorado in response to actively subsiding extensional basins and adjacent high-relief uplift areas. Hot brines developed within the Pennsylvanian strata, migrated laterally to, and moved upward vertically along, basin- margin faults during continued Pennsylvanian subsidence and deposition. These metal-rich brines migrated into karst-solution features within the Lower and Middle Paleozoic dolomites and limestones, principally within the Leadville Formation, in basin- edge uplifted locales where the Pb-Zn-Ag minerals were precipitated. Field relationships, mineral assemblages and paragenesis, fluid-inclusion data, and isotope studies suggest that the metals and brines were derived within the Pennsylvanian sedimentary sequence and that the ore minerals were deposited under different temperatures and at different depths from deposit to deposit. Chemical reaction with the carbonate cave sediment and wallrock, cooling of fluid temperatures, and mixing with meteoric ground waters were the probable combined causes of mineral deposition in the karst-solution features. Late Cretaceous-Tertiary intrusive activity has subsequently modified some of the primary Pb-Zn-Ag deposits in local areas.

Jan 1, 2013

By D. W. Frommer

In continuing its long range studies of methods of treating low-grade iron ores, the Bureau of Mines has developed a new selective flocculation, desliming, and flotation procedure that enables effective beneficiation of the finely disseminated ferruginous jaspers of the Marquette range, Mich. The process, developed on a bench scale and later confirmed in the 800-lb/hr pilot plant, comprises dispersion, selective flocculation, desliming to reject fine silica and clay, and flotation of silica from the remainder of minus 400-mesh pulps. Pilot plant flotation of two Marquette range ores, using the selective flocculation procedure on feeds containing 36 percent Fe, yielded iron recoveries of about 84 percent in concentrates containing 65 to 66 percent Fe and 4 to 5 percent silica. These results were metallurgically superior to those obtained when selective flocculation was not used. Also operating characteristics were better, and reagent costs were lower.

Jan 1, 1964

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

Fine coal is substantially more costly to process than coarse coal because of technical difficulties associated with separating fine particles and removing process water from both clean coal and refuse. Therefore, companies are often forced to discard coal fines to waste impoundments. According to a recent report published by National Research Council, the U.S. coal industry is discarding 70-90 million tons of coal fines annually to 713 active impoundments, most of which are located in Central Appalachia. On October 11, 2000, a 72-acre impoundment near Inez, Kentucky, accidentally released 250 million gallons of coal slurry into nearby underground mines, creeks, rivers, and schoolyards, thereby creating serious environ-mental concerns. Fortunately, recent advances in separation technologies make it possible to recover fine coal more efficiently from existing coal preparation plants and from waste streams previously discarded to impoundments. The availability of these new technologies allows companies to increase profitability and minimize environmental risks, which are conducive for achieving sustainable mining.

Jan 1, 2003

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

By J. Bowders

A case study describing the expansion of Marion County landfill is presented. The exapansion area is located on a deep mined area. Finite element analyses were used to predict the surface subsidence and associated tensile strains on the landfill liner of the expansion site. A synthetically reinforced liner system is recommended to minimize the impact of the subsurface movements on the integrity of the liner system.

Jan 1, 1986

By D. E. Ranta, M. W. Ganster, A. D. Ward

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1992

By T. R. A. Davey, J. W. Sherman, B. J. DiSanto, G. Bjorling, G. S. Stacey, J. T. Cullom, R. L. Bird, S. E. Woods, J. C. Blair, Jorma Honkasalo

Most pyrometallurgical processes take place at high temperature with rapid chemical reactions when the elements and compounds are usually liquid or gaseous. Smelting. The classical method of obtaining a metal from its ore or concentrate is to smelt it in a furnace. The initial letter "s" of this word implies that, in addition to the physical process of melting, a chemical change also occurs. This is usually the reduction of metal oxide to metal by carbon or through a series of processes involving oxidation and reduction. Since solid-solid contact would not be sufficient to give a high rate of reaction, most smelting reactions occur by medium of two reactions involving solid-gaseous contact: where M represents a metal. The commonly preferred unit for carrying out these reactions is the blast furnace,1 which is a vertical shaft of refractory brick or water-cooled steel in which lumps of metal oxide and coke are fed at the top, and an air-blast is injected through tuyeres (water-cooled pipes) in the bottom. Molten metal is withdrawn from a pool at the bottom of the furnace, while N2, CO, and CO2 gases leave the top of the furnace, carrying some fine dust or fume with them, which

Jan 1, 1985

By M. T. Long

The Crestmore Limestone Mine of Riverside Cement Company in Riverside, California is situated within 1.6 km of the Santa Ana River. It is an alluvium covered deposit with a massive quartz manzonite intrustion separating the upper and lower limestone beds which dip from 30° to 50°. The highly fractured upper bed contacting the Santa Ana alluvium contains many unique water inflow problems which vary, from multiple high pressure 19 liters per minute inflows up to 3,000 liters per minute to 11,000 liters per minute inflows-contacted by development mining in April 1983. A case history of the successful grouting of these inflows and the continual grouting procedures in advance of present mining with empirical&apos; results are discussed.

Jan 1, 1984

By Argenis Gamboa

The Arab community is formed by around twenty countries in Africa and Asia, linked basically by a common language-Arabic - and the same religion, the muslim. They jointly occupy around 12 million square kilometers with a total population of around 140 million people. Nevertheless, these nations differ widely in their geographic area and population. Thus, while Egypt has a territory of over a million square kilometers and a population of nearly 40 million people, Kuwait, Qatar and Bahrain have, among the three of them, less than 30, 000 square kilometers and a million inhabitants. The per capita income also vary greatly, depending on whether they are oil producing countries or not. Generally speaking, it can be said that these countries economies have been based on oil or agriculture and that in these last years, they have been making serious efforts to increase their degree of industrialization and have greatly improved their infrastructure. This trend has resulted in the development of the iron and steel industry, which is still in a stage of primary development.

Jan 1, 1979

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998