Search Documents

By Takeshi Tanaka, Yasuhiro Komamura, Yuusaku Tominaga, Takayoshi Iwamoto

In order to assist better countermeasures for ventilation control in normal/abnormal condition of mine ventilation network in real time, branch relation table derived from a macroscopic characteristic of ventilation network is introduced in this study. The main results in this study are as follows; 1) One of macro characteristics of a ventilation network, as a relation between airflow rates in two branches chosen arbitrarily, is specified under the change of aerodynamic resistances in a branch. Airflow rate in a branch can be estimated by airflow rate in other branch changing aerodynamic resistance by using empirical formula. The empirical formula by computer simulation of the Horonai coal mine, Japan is considered to be a one-valued function with monotone or extremums. 2) A branch relation table shows the macro characteristics, mentioned above, of all the set of two-branch combinations in a network. Elements in the table give both information of control possibility range of airflow rate and total number of extremums in an empirical formula. 3) It is important that when aerodynamic resistance change in a branch is estimated by measuring airflow rates in two typical branches, the two branches should be chosen from branch combinations with monotonous relation in the branch relation table. 4) A flexible expert system to assist ventilation control in the specified branch in real time has been developed by using a branch relation table for a ventilation transfer diagram of the specified branch, such a coal face and an advancing face. A fuzzy reasoning is utilized in the recognition of the safety factor, methane concentration, in the system. And when conviction degree in recognition for methane concentration at the specified branch is too low, the system searches for other branch combinations in the branch relation table stored in the system, to use other ventilation transfer diagram of the specified branch. When a needed ventilation transfer diagram is not stored in the system, the expert system asks automatically the ventilation simulation from other computers linked to the main computer automatically. The system repeats consultation until conviction value of safety in the specified branch approached

Jan 1, 1993

By G. E. Slagel

On August 3, 1987, a hearing was held by the House Subcommittee on Energy and the Environment to commemorate the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). Four panels of environmental/citizen group representatives went before the Subcommittee to report on the state of affairs (from their perspective) of the coal industry and the Office of Surface Mining, Reclamation and Enforcement (OSMRE) As expected, these groups had little positive news to report and continued to focus on glaring deficiencies within the surface mining program. They indicated that gross abuse of SMCRA has continued over the past ten years and the states have performed poorly. Congressman Udall's opening comments perhaps best characterized the mood of the group with his statement that "The Act has not accomplished what I or the people of the coalfields had hoped." and " ? a segment of the coal industry has continued in its bitter and implacable opposition to the most basic of environmental controls."

Jan 1, 1988

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By S. B. Castor

Although production generally satisfies demand for rare earths, new markets may make undeveloped resources, particularly those rich in yttrium, more interesting. A Precambrian carbonalite orebody at Mountain Pass, California, has been the world's largest rare earth producer. Minor rare earth production comes from titanium placer mining in Florida and uranium mining in Canada. Prior to operations at Mountain Pass, North American production was mostly from placer deposits that constitute large, low-grade rare earth resources. Newly discovered North American rare metal resources in peralkaline igneous rocks are potential yttrium producers. Most of these resources are in a continent-wide belt of anorogenic magmatic rocks approximately coeval with mineralization at Mountain Pass. Other untapped rare each resources in North America are generally light rare earth-dominated and small or of low grade.

Jan 1, 1991

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By Q. Feng

Study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature and curing time, significantly affect the mechanical property of geopolymer matrix. Through optimization, an above 100 MPa compressive strength has been achieved with the geopolymerization products. Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength even after a one month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS and XRD are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method to apply fly ash as a high strength water-resistant precast construction material. INTRODUCTION Geopolymerization is a process of obtaining a polymeric structure from aluminosilicate by dissolving aluminosilicate sources in a strong alkali (NaOH) solution and condensation of free [SiO4] and [AlO4] tetrahedral units (Davidovits, 1985 and 1988; Duxson et al, 2005; Xu et al, 2000, 2002). After being cured at an elevated temperature for a specific time, the geopolymerization product shows a greatly increased compressive strength. Therefore, the product can be used as construction material such as bricks and road pavement. It provides a very promising method to apply aluminosilicate sources such as fly ash as a construction material for a sustainable development. Fly ash is a main industrial waste which needs to be carefully impounded because of its potential impact on environment. Many efforts have been tried to utilize fly ash as construction materials substituting Portland cement because of the following reasons. First, fly ash is a silica/alumina rich aluminosilicate source, which makes the specific material an ideal source for the geopolymerization process. Secondly, the particle size of fly ash is usually very small (< 50 microns) and it saves a lot of energy consumed during the production process of cement for grinding. Thirdly, fly ash is an ideal source for geopolymerization because it is reactive to alkali even at a mild temperature. In the past twenty years, many studies have been carried out on the geopolymerization of fly ash to a make construction material. However, there are some disadvantages associated with the conventional methods of treating fly ash (Palomo et al, 1999; Perera et al, 2007; Temuujin, et al, 2009; Hanjitsuwan et al, 2014). First, in most of the proposed geopolymerization methods, a salient amount of sodium silicate has to be added. It therefore makes it complex whether the achieved mechanical strength of geopolymerization products is due to a real geopolymerization process between fly ash and alkali or just largely the solidification of metal silicate in air at an elevated temperature. Secondly, the authors have noticed that when the geopolymerization product is soaked in water, the solution pH increases sharply and the products will lose its compressive strength gradually in water. Thirdly, the compressive strength of the geopolymerization product as reported is usually less than 50 MPa.

Jan 1, 2019

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

By V. Srivastava, T. Ghosh

"Modeling and Simulation of SAG Mill has been widely used in design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. This paper attempts to characterize mill contents by solving Whiten’s first order contents based model in Matlab/Simulink environment. The parameters in the model such as breakage rate (S), discharge rate (D) and appearance function (A) were estimated utilizing process and design data collected from a gold mine operating in Alaska coupled with nonlinear parameter estimation scheme. This model is then utilized to predict dynamic response of other key operational variables such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated utilizing dynamic response data from the plant to encompass operational characteristics of SAG Mill behavior. Keywords: SAG Mill, Dynamic Modeling, Simulation, Nonlinear Parameter Estimation. INTRODUCTION Grinding in mineral industry is one the most important steps in the process of size reduction and plays a crucial role in determining the overall economics of the milling plant. Much of the efforts focused on improving the process efficiency using modeling and simulation have been practiced by researcher and engineers. However, up till now these models were simulated under steady state approximation because of their complex nature and difficulty in programming them in a dynamic framework. Steady state simulations have been successfully utilized in circuit designing, capacity planning and pre-flowsheet optimization. The maturity in steady state models is because of its applicability and regular use in steady state simulation packages such as JKSimMet, Limn, ModSim, etc. With the advent of equipment such as SAG and AG mill has been a recent shift in the simulating these models using dynamic approach. Because of the economic benefits of these devices and ability to act both as a primary grinding device and as secondary or tertiary crushing device they have gained a large popularity and are now universal to any milling plant. However, these device poses a real challenge to engineers and researchers in terms of operation and control. The major reason attributed to problems faced is because the ore constitutes the major portion of the charge in these devices when compared to ball and rod mill. This rock charge is subjected to disturbance such as changes in feed size distribution and ore hardness which results in unstable operation and frequent mill stoppages. One way to prevent this is to measure and control these external variables, however, lack of available instrumentation and unavailability of sensors to measure these variables has foiled the understanding of complete process occurring inside the mill thereby, inhibiting development of proper control system."

Jan 1, 2017

By W. C. Morgan

The Federal Surface Mining Law enacted in 1978 is now being translated into regulations which must be followed in future coal mining. Substantial change to mining procedures is required to maintain stricter air and water control while mining and to return the mined out land to equal or better use than before. These changes do not come easy; and in most cases, they create a substantial additional cost. Based on field observations and mining studies, Caterpillar has been making suggestions on the use of their types of equipment to conform to the new standards at the least cost. This paper will be a brief review of some of the overburden stripping and reclamation methods suggested by Caterpillar. A production and cost comparison of dragline, scraper/dozer and truck, loader systems in 20 to 150 ft. Overburden conditions illustrates potential cost savings using mobile equipment.

Jan 1, 1980

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By C. Timothy Shaw

Traditionally, only the large mining companies have maintained specialist departments in such areas as Rock Mechanics, Ventilation and Safety. To the small companies this has been a luxury that they could ill afford. Any work required by such companies in these areas, more complex than could be handled by the existing staff, was done by consultants. This situation is changing though and there is a need arising for many specialist departments. These changes are partly being brought about by the effects of inflation as the ever increasing costs are causing more and more operators to increase the size of their operations in search of economies of scale. In addition though the plethora of new laws and regulations are creating a need for many more specialists in all areas of mining in order to ensure compliance. The abovementioned factors, added to the existing Pattern of mines endeavoring to improve the working environment for their labor force, both for reasons of practical labor relations and also due to further legislative pressures, have thus created a climate where, in the near future, departments such as Rock Mechanics, Safety, Ventilation, Environmental Engineering and Subsidence Control will be commonplace in mining companies. It will no longer be practical to function without such services. Many mining companies already maintain such departments and this has particularly been true of the big mining groups of South Africa. From the experience gained by many of these large companies with specialist departments, it is clear that the maintenance of a cadre of experienced, competent professionals in such a department has not always been easy. It would seem from the experience gained that one can generalise and state that graduate mining engineers tend not to view specilisation as an optimum direction for their career development. It is of course true that many professionals, especially those with higher than a bachelors degree, do view these areas as valid career options, but even here experience shows that wastage is high. The time therefore seems to be ripe to take a look at this area in some detail to see whether reasons for the problems can be isolated. Working from that some suggestions can be made as to directions in which improvements might be made. If the challenge of the demands of the new regulations are to be met then such improvements must be made.

Jan 1, 1980

By Charles J. Hass

INTRODUCTION Deformation measurements are some of the simplest and most useful measurements that can be made by the mining/rock mechanics engineer in assessing the sta¬bility of openings in rock. A number of tools and tech¬niques are presently available. This chapter will de¬scribe the most common instruments, their application, and present the equations needed for data reduction. MECHANICAL STRAIN GAGE Description of Instrument A mechanical strain gage of the Whittemore type shown in Fig. I is a useful instrument for measuring deformations of pillars, sidewalls, and roofs of under¬ground mines. Measurement gage lengths typically range from 51 to 254 mm (2 to 10 in.), and the dial indicator reads to 0.0025 mm (0.0001 in.). The instru¬ment measures the deformation between precision gage points which are anchored in the rock. The anchor points are typically grouted in small holes drilled 12.5 mm (1/2 in.) or so deep into the rock. Strain a is calculated from the measured deformation AL with the equation [ ] where L is gage length. A necessary accessory for the instrument is a master bar normally made from invar steel having a low co¬efficient of thermal expansion. This bar allows one to check the instrument for changes in the mechanical zero point and to correct for temperature effects on the measuring instrument. The instrument is available from Soiltest, Inc. for a cost of approximately $340; the cost of the master bar is approximately $55; and nonreusable brass inserts which are anchored in the rock are nominally priced at $0.27 each. All prices are for 1978. Applications Two classes of applications may be considered, one where only one measurement direction is involved and the second where three measurement directions are em¬ployed. Applications where only one measurement di¬rection is necessary include: monitoring crack or frac¬ture separation or shear movement with anchor points on opposite sides of the discontinuity; measurement of vertical strain in a pillar or sidewall; and measurement of steel support deformations with anchors in the steel members. The more general application involves a strain ro¬sette consisting of three measurement directions which for convenience are oriented 1.04 rad (60°) apart to form an equilateral triangle as shown in Fig. 2. Strains in the three measurement directions [ ]

Jan 1, 1982

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By J. Iannicelli

Kaolin tailings ponds play an important role in reclamation of land and water. Discharges impounded from kaolin plants include oversize fractions consisting of coarse kaolin, mica, quartz as well as magnetically extracted contaminents, acid filtrates, and plant washdown streams. Tailing ponds perform an essential function in sedimentation of particulates, blending and reoxygenation of liquid waste, and neutralization and clarification of discharge water. During the past fifteen years, most kaolin firms have segregated their coarse filler waste to allow for possible reclamation for production of delaminated coating clay. This excess coarse filler fraction constitutes a reserve for future coating clay production.

Jan 1, 1985

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By Olav Moklebust

The R-N Process is an outgrowth of the development by the National Lead Company&apos;s Norwegian subsidiary Titania A/S, of a process for producing metallic iron and a high titanium content co-product from ilmenite. Development of the process for the treatment of iron ores was continued as a joint project of the Republic Steel Corporation and the National Lead Company in 1953. More recently in July, 1957, the R-N Corporation was created by these two companies to undertake the commercial promotion of the results of this joint project. This paper has been prepared with the permission and encouragement of these three companies. The R-N process has as its objective the making of metallic iron from iron ores or iron ore concentrates. The general principles of the process have already been disclosed in technical papers and patents. In general the process comprises the following steps: 1. Iron oxide in crushed natural iron ores or iron ore concentrates is reduced to about 95% metallic iron, without fusion in a rotary kiln in the presence of solid carbonaceous fuel,*such as, coke or char, limestone and combustible gases. 2. The kiln discharge, consisting of metallized ore, coke, lime and coke ashes, is cooled. The excess coke is regenerated and recycled to the kiln feed.

Jan 1, 1959

By Geno Saccomanno

INTRODUCTION Cancer of the lung in uranium miners has been reported by many authors. In fact, it has become a most popular subject for comment by environmentalists, health physicists, and newspaper writers. I believe it appropriate for me to discuss cancer of the lung in uranium miners in a general way commenting briefly on etiology, incidence, tumor cell types, and particularly, tumor development and treatment. Cytological development of cancer in its incipient stages, particularly the in situ stage, relates to potential cure with photoradiation, early diagnosis, and treatment. Our observations of the cytological response to this modality of diagnosis and treatment will be discussed briefly since this area will also be covered by Doctor Balchum. The cause of lung cancer in uranium miners is primarily due to two carcinogens; cigarette smoking and radon daughter radiation. Cigarette smoking has continued at the same intensity over time among uranium miners; about 60% of the miners are cigarette smokers and 40% are non-smokers. Radon daughter exposure to the uranium miner has varied from mine to mine, but over the last 20 years has been reduced to a minor fraction (.3 WL) of the level that prevailed in many of the mines during the 1950-1960 era when many of the miners were exposed to more than 10 WLM. Sputum samples have been examined on as many uranium miners as responded on the Colorado Plateau since 1956. Autopsy studies were done whenever this was permissible. In some instances, only tissue from a biopsy of a node or lung was available for study. Smoking histories were also taken. Approximately 200,000 sputum samples were examined and histological examinations of lung lesions were made from 312 cases. METHODS The method of sputum cytological collection and preparation was reported previously. I The lungs were fixed with formalin and prepared for sectioning by Dr. Oscar Auerbach with his block-section method. RESULTS Three-hundred-twelve lung cancers from uranium miners were examined. The tumor types and the age at death for each type, smokers and non-smokers, are given in Table #1. The incidence of the tumors in the smokers and non-smokers is given in Table #2. The incidence of small cell carcinoma of the lung has decreased from an incidence of 76% of all the lung cancers found in uranium miners to 22% of these lesions (Figure #1). The decrease in incidence of this tumor is probably due to decreased exposure to radiation in the mines.

Jan 1, 1981