Search Documents

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline?s long-term performances and availabilities, to develop preventive maintenance plans, and to make future projections about the machine?s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, PAGE 736 and MARION 7820, which have been operating in Tunçbilek open cast coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages as: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data; (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (20 yd3) is seemed to be more reliable and less likely to fail when compared with Marion 7820 (40 yd3). The operating hours without failure range from 41 to 51 hours with 50 percent reliability.

Jan 1, 2011

By Williams R. Reynolds

Studies of the northeastern Mississippi bauxites were initiated primarily for the purpose of ascertaining the quality and quantity of the ore. Subsequently, this ore was found to have a rather dubious economic value as was previously suspected but never established in earlier economic reports (1, 2, 3). However, the quality of ore was found to be higher than previously thought. Even though the ore bodies were determined during the early stages of this study to be too thin, small and widespread for commercial production a continuation of the study was not abandoned. On the contrary, the present investigation was intensified concentrating less on the economic application and more on stratigraphy and genesis. Considering the ever increasing demand for aluminum products the northeastern Mississippi bauxite district which includes portions of Tippah, Benton, Pontotoc, and Union Counties may soon become, in spite of inferior quantities of ore, an attractive area for bauxite production. Presently, however, the meager quantity of ore discourages exploitation. On the other hand, these northeastern district bauxites are facies of more extensive units of lignite bearing high aluminum clays, and considering the advances in aluminum extraction from clay these clays may in the future beckon mining interest. The bauxite of the northeastern Mississippi district, mapped as a part of the Betheden Formation (4). has an outcrop trend along the county lines of Tippah and Benton Counties and the extreme western portion of Union and Pontotoc Counties. Studies of exposures and cores stratigraphically positions the outcrop between the middle Midway Porters Creek Clay and the lower Eocene Wilcox sands and

Jan 1, 1977

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By Paul Richardson

This paper discusses the drilling techniques and equipment used by Loffland Brothers Company to drill the AEC's UC-3 large diameter shaft in Nevada. Included are pictures and illustrations of the drilling-mud circulating system, the surface and downhole drill-string and the special heavy-duty mast and hoisting equipment required to do the job. The purpose and method of lining the large diameter holes along with the technique and materials used to backfill the lining to hole annulus are discussed briefly. Areas requiring improvement in both equipment design and technology for large diameter shaft drilling are discussed briefly. Shafts as large as 140 inches in diameter to depths of 5,000 feet can be drilled with existing equipment and technology.

Jan 1, 1969

By R. M. Geisenheyner

We are in the midst of a transportation revolution. From the Wright Brothers to the SST. From the Toonerville Trolly to the 120-mile-an-hour Northeast Corridor train. From Christopher Columbus to Neil Armstrong. There is another side to this revolution and it is going on every day at our mines and factories. We call it bulk distribution. Perhaps ordinary sounding, but every bit as exciting as those other transportation innovations. Basically, we have gone from bag to bulk, and in the process reached that Last Frontier in manufacturing cost savings. By revitalization of our distribution system, we have made it possible for our mines and factories to realize fully the vast economies of spage-age manufacturing techniques and accomplishments. The pacesetters in this distribution revolution have been you gentlemen, the producers and shippers of dry mineral products. In this area bulk distribution grew up. And here most of the current innovations are being introduced. Management of your industry was early to realize the economic advantages of bulk distribution. Distribution costs of your products comprises a sizeable, portion of the selling price and management is sensitive of any developments which may even slightly reduce the cost of transportation, marketing or the exploration of new frontiers.

Jan 1, 1969

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By J. W. Mausteller

Chemical oxygen supplies have been used for nearly 60 years, with their greatest application during the last 25 years. They are of two types, the superoxides and chlorate "candles", The superoxides are demand chemicals, responding to the needs of the user and to supply oxygen and remove carbon dioxide. Chlorate candles are formed solid element which furnish oxygen only and do not remove carbon dioxide. Properties of these materials will be described, with comments on the respiratory requirements of a man under various workloads, types of equipment which use chemical oxygen, comparison with other systems and potential application to an underground mine survival system.

Jan 1, 1971

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By Yves Picot

Construction of new installations was recently completed in the Port of Tubarao, Brazil, With this expansion the port, operated by Companhia Vale do Rio Doce (CVRD), has become the largest iron ore port in the world, with an annual throughput capacity of 60 million long tons. GROWTH OR IRON ORE EXPORTS Since its formation CVRD has steadily increased the shipment of iron ore to overseas markets. Starting with less than 100,000 tons in 1942, the yearly export volume grew to 1,500,000 tons in 1951, 5,000,000 tons in 1961 and 25,000,000 tons in 1971. The number of different grades of ore also increased during this period. Production of high grade pellets, starting in 1970, further increased the number of ore products to be shipped. In the same period the size of ore carriers increased twenty-fold to over 250,000 DWT.

Jan 1, 1974

By Khosrow Badiozamani

Depletion of easily accessible coal reserves and stringent competition in coal marketing has led to the coal industries' need to more accurately assess alternate development scenarios and to develop well-conceived produc¬tion plans. This, in turn, has encouraged the active use of the computer during resource eval¬uation and mine planning. Morrison-Knudsen, (M-K) has developed proprietary software, known as "EAGLES", to support not only its own mine planning and development activities but also the mining industry in general. The EAGLES system provides complete geologic modeling, mine planning, production modeling, equipment modeling, and cost and financial modeling capabilities. In addition, EAGLES can be used for geotechnical studies, environmental assessments, and surface and groundwater hydrological evaluations. Another important tool used in today's mine development is Landsat (remote sensing). Landsat is especially useful in the evaluation of mining activities at remote mine locations and for megascale assessments of geologic structures and hydrologic regions. The use of scientific systems in the development of surface mines is being well integrated into today's mining operations and will be a major factor in the planning, development, and operation of mines in the future.

Jan 1, 1985

By Y. C. Guan

The dissolution behavior of silver and copper form their elemental states and Ag/Cu alloys in ammoniacal solutions has been studied using rotating disc electrodes. The variables studied included concentration of ammonia, oxygen partial pressure and rotating speed of the disc. The results have been interpreted in terms of the mixed potential theory. The effect of local current resistance on the overall current has also been examined as a part of the governing theory of the dissolution. It was observed that the dissolution potential and the rate of dissolution were very much affected by the composition of the alloys.

Jan 1, 1995

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. This study was made at the Mines Experiment Station of the University of Minnesota under the sponsorship of the Great Northern Railway Company. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semi- taconites and also the wash and heavy media ore types widely developed in the area. Each basic, original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type.

Jan 1, 1964

By L. Adler

To properly analyze and apply mining equipment, a systematic, current, inclusive, and simple classification scheme is required. This paper provides such a classification for Roadheaders. This Roadheader classification is based on factors, such as the rock cutterhead, the boom type, and the chassis configuration. It first assigns Roadheaders as an equipment type within the larger group of Integrated Excavators. The Roadheader type is then delineated into the following subtypes: the standard, the extended boom, the tunnelers, and the miscellaneous. Next, these subtypes are devolved into kinds, and finally variants and attachments are considered. To resolve inconsistencies in characterizing the Roadheader, cross-referencing is employed within the classification scheme.

Jan 1, 1996