Search Documents

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By R. J. Matetic, Peter G. Kovalchik, Jeffrey Shawn Peterson

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included various combinations of rotational speeds and thrusts; hex and round drill steels of one inch (1.) and one and three-eighths inch (1 3/8.) diameters; vacuum and wet conditions; and using drill media of differing compressive strengths. This paper will detail the affects of each of these on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

Jan 1, 2005

By John Drew Ridge

Recent work by Haas has made available information on densities and vapor pressures of solutions of differing salinities at temperatures up to 330°C. From these data it is possible to predict the behavior of volcanic exhalations of various degrees of salinity as they approach the sea floor. Particular attention is devoted to solutions of 5.0 weight per cent NaCl and 20 weight per cent NaCl, two fluids that approximate quite closely the salinities of what Roedder termed: (1) normal hydrothermal fluids and (2) fluids typical of stratiform deposits of low-temperature conditions of origin. It is apparent that solutions above 220-230°C. cannot reach a sea floor on which the depth of water is 600 feet or less in the liquid state but will boil at some appreciable depth beneath the sea floor. Such boiling would result in the precipitation of all constituents of the ore fluids of significantly lower vapor pressure than water. The principal such constituent would be salt, and no sulfide deposits, the major constituent of which is salt are known. It follows, therefore, that ore fluids probably never get close to the sea floor of shallow seas at temperatures high enough to permit boiling. Ore fluids significantly above 230°C. can reach the sea floor in the fluid state only if the depth of the sea in the area. in question is well above 600 feet, for example, solutions at temperatures of ±300°C. reach the sea floor in the liquid state only if the depth of sea water is slightly over 3000 feet. Ore fluids reaching the sea floor at such depths may be the parents of such fluids as the Red and Salton Sea brines. On the basis of these data, the Cyprus and Kuroko deposits are discussed.

Jan 1, 1973

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By Omar A. Muhtadi, R. Bruce Thorndycraft, David A. Milligan

9.1 INTRODUCTION Precious metals in a leach solution are extracted, concentrated, and purified to complete the process begun in the heap and to produce an end product which will provide an economic payback to the mine developer/operator. Several different processes are required to convert the dissolved precious metals into pure metal bars. This chapter discusses the actual production of metal once it has been recovered from the pregnant leach solutions by the zinc cementation (Merrill -Crowe) or carbon adsorption processes. Metal production is generally taken to mean the production of a fairly pure "dore" bar. This chapter also reiterates some information from Chapter 8 in a slightly different context, since the focus of Chapter 8 was a fairly detailed description of the two actual recovery processes, whereas the focus of this chapter is metal production. The sale of an intermediate precious metal product is possible (as opposed to the production of dore bars at the mine site); however, the value of the precious metals is reduced by the various charges and risks associated with precious metal processing. For this reason, most operators choose to produce the most refined metal possible in order to maximize project economics. Precious metals may be extracted from the leach solution by both conventional and unconventional processes. The conventional processes are activated carbon/electrowinning (ACE) and zinc precipitation (ZIP). The unconventional processes are resin ion exchange, solvent extraction, and direct electrowinning. A typical ACE process has two circulating loops. The first loop adsorbs the cyanide-metal complexes from the dilute leach solution onto the activated carbon. A second, separate solution loop removes the cyanide-metal complexes from the activated carbon into a strong solution, the electrowinning electrolyte. Activated carbon is transferred from one fluid loop to the other. The operating cost of the ACE process is directly proportional to the quantity of carbon stripped and thus to the quantity of precious metal produced. A typical ZIP process contains a single circulating loop. The solution is filtered, deaerated, contacted with zinc, and filtered again. The barren leach solution is then returned to the heap. The zinc sludge recovered in the

Jan 1, 1988

By Omar A. Muhtadi

8.1 INTRODUCTION Several methods currently exist by which gold may be recovered from a pregnant leach liquor. Two of these methods are discussed in this chapter, the Merrill-Crowe (zinc cementation) process and the carbon adsorption process. These two methods represent the most frequently used techniques for gold extraction and are, -in fact, used almost exclusively in U.S. heap leaching operations. Because of the efficiency and ease of use of these two methods, it is extremely likely they will continue to be quite prevalent within the gold mining industry in years to come. The remainder of this chapter includes information on the history of the two processes, descriptions of the actual processes, criteria to consider in selecting a recovery process, and commercial design and construction considerations for both of the gold recovery methods. As with other chapters in this book, some fairly technical information is presented for the benefit of those readers needing a greater level of detail. However, the overall intent of the chapter is to provide an overview of the processes likely to be used in gold extraction, thus giving the reader a firm basis for more technical research into the topic, should this be needed. 8.1.1 History of Zinc Cementation During the late 18901s, zinc cementation was introduced for the precipitation of gold and silver from cyanide solutions. This occurred at about the same time as the introduction of the cyanidation process, the history of which is recapped in Chapter 1. The initial cementation process involved introduction of a gold-bearing cyanide solution onto a bed of zinc shavings. It proved to be quite inefficient because the reaction rate was very slow. The zinc quickly became "passive", inhibiting further gold deposition. Shortly after this first introduction, zinc precipitation was improved by adding a lead salt (usually lead nitrate) to the zinc. This allowed a zinc-lead couple to form on the surface of the shavings, eliminating passivation of zinc surfaces and thereby allowing continued deposition of gold. Further improvements were shortly forthcoming. The first of these involved the use of zinc dust rather than zinc shavings. This provided a much

Jan 1, 1988

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By A. R. MacPherson

The procedure to arrive at an energy efficient autogenous grinding plant is carried out in the following steps: First Step - Determine power requirements to grind a particular ore. This work carried out on small samples ground in a 450 mm diameter Aerofall Hill and the results are checked against a standard Bond Index test. Second Step - A bulk sample from the ore zone is ground in a 1.8 m diameter pilot mill. This work is carried on until the power objectives as indicated from the first step have been realized. Third Step - Correlate the pilot mill data, with the data from the numerous samples ground in the small 450 mm mill and arrive at design criteria for the commercial plant. Ensure commercial mill design will be suitable to obtain similar results as those obtained in the pilot mill.

Jan 1, 1981

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

Last year in the US alone, about 425 Mt (468 million st) of minerals and coal were beneficiated by froth flotation. This number indicates that from 1983 there was a 10% increase in tonnage of min¬erals and coal beneficiated by the indus¬try. A significant improvement was seen in the tonnage processed by the nonferrous minerals and coal industries. BP Minerals America installed 85 m; (3000 cu ft) flotation cells at the Bing¬ham Canyon mine and concentrator. The new flotation circuit has fewer than 100 cells compared to 2000 flotation cells used in the old plant (Mining Engi¬neering, November 1988). Column flotation use on a commer¬cial scale continues to expand as seen from the interest expressed at the Col¬umn Flotation Symposium (Column Flotation &apos;88). The Magma Copper Co., San Manuel Division replaced all con¬ventional cells with 1.8 x 12 m (6 x 40 ft) column flotation cells for copper con¬centrate cleaning. Also, 1220 mm and 760 mm-diam (48 in. and 30 in.-diam) column cells are operating at the plant in the molybdenum circuit. A commercial Diester Flotaire col¬umn cell for fine coal recovery was installed at the United Coal Wellmore No. 20 plant. The 36.8 m3 (1300 cu ft) cell recovers 13.6 to 18 t/h (15 to 20 stph) of -590 gm (-28 mesh) coal. A similar unit has been installed at Tanoma Mining Co. in Pennsylvania. Various modifications of the column cells are being designed around the world. Jameson (Mining and Metal¬lurgy, 1988) described a new concept whereby the feed and air stream mixture is discharged into a cylindrical column of about 1.2 m (4 ft) height. Recovery and grade of nonferrous minerals have been reported to be better than that in a four-stage conventional flotation clean¬ing circuit. Flotation reagents American Cyanamid and Dow Chemical continued development of a new generation of sulfide collectors. A general feeling is development of new sulfide collectors has not kept up with flotation technology. Additionally, joint efforts between industry and chemical suppliers will likely be necessary to realize the economic benefits of the new technologies, since new chemistries respond differently compared to the conventional collectors. Flocculant development in recent years has been evolutionary rather than revolutionary. Rothenborg reported on development of a new flocculant family (a hydroxymated polyacrylamide desig¬nated S-6703) that has shown consider¬able promise in red mud clarification. Plant testing showed that this new floc¬culant could replace starch and poly¬acrylate and provide significantly higher overflow clarity. Barol Kami (Siirak) and Cleveland¬Cliffs (Hancock) reported development of an amphoteric apatite collector (ATRAC 873) that was used in Tilden&apos;s silica flotation process to increase apatite rejection. The collector was engineered for the particular flotation conditions in the complex Tilden process. Significant plant testing with ATRAC 873 showed that this reagent gave significantly in¬creased apatite rejection without any effect on silica flotation effectiveness or selectivity. Electrostatic separation Electrostatic separation is now em¬ployed in the precious metals mining industry to recover gold and silver grills from crushed slag. The installation at Paradise Peak has prompted other op¬erators to consider this application. In another development, attractive potentials for treating very fine minerals (-45 µm or -325 mesh) are being devel¬oped by Advanced Energy Dynamics and by the Department of Energy. Demonstration tests using triboelectric charging/electrostatic separation have been successful on a variety of minerals as well as coal. Magnetic separation Developments in magnetic separa¬tion have transpired on a production scale. Superconducting, high gradient magnetic separation has gained accep¬tance with the successful startup of a second unit treating kaolin at J.M. Huber Corp. This liquid-helium-cooled mag¬net generates 2.0 tesla in a 3-m-diam (120-in.-diam) bore with no power con¬sumption. Wet, high-intensity magnetic separation has been applied to sulfide mineral separations both domestically and abroad. These continuous type of separators are effective in removing residual chalcopyrite and sphalerite from other base metal sulfide concentrates. Separators using high energy rare earth permanent magnets are continu¬ally increasing. Now offered as both drum and roll type, these units are be¬coming a staple in the processing of industrial minerals. Tests using rare earth magnets strategically placed on a spiral concentrator have demonstrated the enhanced recovery of heavy miner¬als such as ilmenite. Classification Although no major technology break¬throughs in classification appear immi¬nent, there is an increasing need for more efficient and cost-effective meth¬ods to make size separations. It is be¬coming more apparent that mineral concentration methods will be more common at very fine sizes, say below 50

Jan 1, 1989

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee&apos;s theme of 1987&apos;s Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950&apos;s, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By Alfred Jr. Petrick, William A. Vogely

INTRODUCTION The scope of mineral finance extends beyond the economic aspects of property evaluation to all of those activities involving acquisition and utilization of funds with an objective to optimize the value of the firm. It must, therefore, en- compass consideration of the overall financial goals of the firm, decisions involving external versus internal growth and domestic versus foreign investments, management of working cap- ital, efforts to minimize the cost of capital, and decisions with regards to the instruments of long- term debt and equity financing. The scope of this section is limited to considerations of special interest to the mineral or petroleum engineer, which include the following aspects of mineral finance: (1) The technical aspects of mineral or coal property or oil and gas reservoir evaluation which provide the basis for estimation and forecasting of revenues and costs. (2) Estimation and forecasting of costs and prices in a inflationary economic environment. (3) Calculation of cash flows which model .. , the investment in minerals, coal or oil, and gas. Such models require assumptions as to the timing of cash flows, escalation of capital and operating costs, base prices, and escalation, the tax regime, royalties, division of profits and the economic aspects of loans. (4) The role of discount rate in the economic analysis of an investment which requires consideration of the opportunity costs of the firm, cost of capital, risk premiums. (5) Risk analysis including application of the concepts of conditional net present value, expected value, and risk preference as well as the application of the techniques of sensitivity and simulation. (6) Selection of application criteria for in- vestment decision making. (7) Capital structure with particular reference to the effect of debt financing. (8) Consideration of sources of funds utilized by the minerals industries. (9) Long-range planning including portfolio analysis. This section is limited to principles, methodologies, and trends in mineral investment, finance, and long-range planning in the United States with a perspective from the year 1984. Consideration of the key concepts is supplemented by case examples of investment risk analysis and financial structure. Important factors affecting mineral investment evaluation during the 1980s include volatile metals prices, cost inflation, and the introduction of techniques requiring the computer and its capacity for improved technical and economic analysis into the hands of those who know most about the industry. The personal computer is replacing the calculator on the desk of the individual analyst and is rapidly becoming a required tool for the study of engineering and economics. Examples of change brought about by the micro-computer include greatly improved techniques of cost estimation, wider application of the computer for project analysis, computer graphics, reserve estimation, geostatistical analysis, mine design and other techniques that capitalize on the ability of the computer to handle

Jan 1, 1985