Search Documents

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By Patrick J. Doig

The NS9 Drop Shaft contract formed part of the Waste Pollution Abatement Program (WPAP) conducted by the Milwaukee Metropolitan Sewerage District (MMSD). The contract involved the construction of two shafts, a deaeration chamber and connecting tunnel, and ancillary facilities. Portions of the construction were located in saturated overburden where dewatering was prohibited. Ground freezing was utilized for temporary support of the excavation. This paper concentrates on the freezing system and the excavation of frozen ground, with particular emphasis on the use of mechanical cutting equipment, including a raiseborer and a roadheader.

Jan 1, 1991

By A. H. Shapiro, W. –F. Leung

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micrometer-range particles that form pastelike, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake flow control structure that allows expressed liquid, from the cake in the dry beach region to be returned to the liquid pool while maintaining a high-solids throughput. To provide optimal performance with various operating parameters (i.e., feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids and slurry type), the cake flow control is adjustable. The second part of the beach is preferably at a zero angle. Tests showed that the new design allows increases in solids dryness and solids throughput. Key words: Dewatering, Centrifuge, Slurry, Fine particles, Beach decanter, Cake-flow control

Jan 1, 2003

By X. Wu, M. G. Karfakis, K. Y. Haramy, B. T. Brady

A quantitative evaluation of damage caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations that are subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain-energy buildup are identified and investigated. A methodology for the evaluation of strain-energy accumulation caused by, an overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude (ML), which depends on the seismic energy transformed from the stored strain energy that is released when the roof fails. A particle-velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and the damage area agree well with field observations.

Jan 1, 1997

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By B. Bergmark, O. Guyot, A. Broussaud, C. Bouché

The Boliden Aitik concentrator in Sweden processes 2,000 t/h (2,200 stph) of low-grade copper ore. The plant consists of five grinding lines that feed four bulk-flotation banks with a scavenger-concentrate regrind mill und a column cleaner circuit with a regrind mill. The authors installed a model-based expert optimizing control system to maximize copper recovery in the bulk-flotation circuit while maintaining an appropriate copper grude in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent- addition rates. It combines the power of a dynamic population-balance model that estimates mineral liberation in each stream, an optimizer that computes appropriate set points and a rule-based module that implements the strategy. The benefits have been evaluated over a period of three months. The model-based expert optimizing control system generates a measurable increase in copper recovery, around 0.5%, and an optimized bulk-concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 2000

By R. Canello, J. Jenkins

El Abra has the world's largest leach, solvent extraction and electrowinning facility, The crushing plant capacity is 120,000 metric tonnes per day and the cathode production capacity is 225,000 metric tonnes per year. The El Abra mine and plant are located in the Province of El Loa, in Region I1 of Chile, 55 km. north of the city of Calama. The ore deposit outcrops on the southern slope of Cerro Pajonal at an altitude of 3,900 to 4,100 meters above sea level. The processing plant and camp facilities are located at a lower 3,300 meter elevation on an alluvial slope, 15 km southeast of the deposit. The operating company, Sociedad Contractual Minera El Abra, is 51% owned by Cyprus Arnax Minerals Company through the Cyprus Climax Metals Company subsidiary and 49% owned by Corporaci6n Nacional del Cobre de Chile (Codelco). The present paper describes the ore reserves, mine operations, crushing, leaching, solvent extraction, electrowinning and infrastructure facilities.

Jan 1, 1998

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By Shail J. Butani

This paper analyzes the 1982 coal mine accident data collected by the Mine Safety and Health Administration (MSHA) for key equipment types, by mine type, and by geographic region. The differences in hazards associated with the various equipment types are studied both in absolute (i.e., total number of incidences) and relative (i.e., incidence rate or the number of incidences per 200,000 employee or exposure hours) terms. The paper compares and contrasts the total number of incidents as well as incidence rates classified by several types of severity measures such as lost workdays cases, mean number of lost workdays per lost workdays case, fatal cases, non- fatal cases without lost workdays, total number of cases, and total number of lost workdays This statistical analysis shows that significant differences in hazards exist not only due to equipment type but also due to mine type and geographic region.

Jan 1, 1986

By H. Fayed

Two-phase (water and air) flow in a self-aspirated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). The geometric model is a replica of a 300 m3 cell. A 72-degree sector containing two blades of the ten-blade rotor has been modeled and periodic boundary conditions are applied in the circumferential direction. Simulation of a sector of the machine allows acceptable resolution of the mean flow field using 4x106 grid points. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Unsteady simulations have been performed. In a self-aspirated machine, airflow rate is not known a prior; it is an output from the CFD simulation. Uniform mean bubble diameter of 0.7 mm has been specified as an input for the simulation. Air flow rate and power consumption have been monitored with time, and results indicate a stable operation. Air volume fraction contours and velocity field in different regions of the machine are presented and discussed.

Feb 27, 2013

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By Robert A. Cortese, Carrie E. Lucci

Mine Safety and Health Administration (MSHA) regulations require underground coal mine operators to dust their mine corridors with an inert material to prevent coal dust explosions. The most commonly used material is pulverized limestone. Current practice to determine compliance with MSHA regulations requires the coal mine foreman or an MSHA inspector to collect samples of the deposited dust, a mixture of coal dust and limestone rock dust, for above ground laboratory analysis. To expedite this process, the U.S. Bureau of Mines has developed two instruments to facilitate the inspection and rock dusting processes, the explosibility meter and float dust deposition meter. The explosibility meter is a hand-held instrument which provides an in situ measurement of the explosible nature of homogeneous mine dust samples. The float dust deposition meter measures the mass loading density of the top layer of coal or limestone dust deposited on the mine floor during mining operations by the ventilation air. It may also be used to automate trickle rock dusting equipment. The operation of each device is based on the difference in the optical reflectance between the light limestone dust and the dark coal dust. The principal of the explosibility meter is based on the observation that, for a fixed coal volatility, the optical reflectance of dust mixtures is relatively constant at the limit of flammability, and independent of the coal dust particle size.

Jan 1, 1995

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

By B. W. Cavender

Capital investments are made for a variety of reasons, ranging from providing incremental capacity at existing operations to developing and implementing new technologies intended to radically improve a company's capabilities. These projects generate very different business opportunities and create value in distinctive ways. For incremental improvements, the capital budgeting process assures at least a loose fit between short-term goals and readily available resources. However, the criteria used to evaluate capital projects often prevent a company from committing to more aggressive goals, which lie beyond the firm's current abilities or resources. Such projects may not have clearly identifiable future cash flows, and the degree of interaction with other projects and the nature of the risk incurred may be difficult to estimate. Additionally, by focusing only on quantifiable benefits, the budgeting process often fails to recognize "soft" improvements such as increased operating flexibility or new knowledge generated by such projects. By rejecting these projects, the capital budgeting process may actually harm the company's future competitive position.

Jan 1, 1999