Search Documents

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By Douglas D. Donald

The financial analyst's job is to make an objective appraisal of the investment opportunities which exist within the various industries under his supervision within the context of the economic model provided by his firm and the a climate of investor sentiments. Industry analysis is critical. When a major investment trend develops, usually the stock of all companies within the specific industry react in the same direction. I should emphasize here, however, that an investment trend is influenced by the economic outlook, but economics is not the only determinant - investor psychology and arbitrary political factors may be of equal or greater importance. Part of our job is to recognize trends early and determine whether they are valid. Following industry analysis, the analyst must examine the specific companies within that industry since some companies usually react more violently than others to industry trends, whether they be favorable or adverse. To simplify the process of evaluating an investment opportunity, it is convenient to isolate three types of factors which have a bearing on every sort of business although the degree of influence of each factor may vary from industry to industry. These categories are, 1) independent or external factors insofar as they are beyond the control of corporate management, 2) interdependent factors insofar as influence may be exerted by industry-wide action, and 3) dependent factors covering the area of internal decisions which are basically under the control of the individual corporate managers. Although the title of this paper, "The Corporate Use of Cash Flow," is only one segment of the third category, it may be useful to continent on the first two categories as well. The independent factors may be either economic or governmental. The economic factors include cyclicality which may be very high in the case of the basic commodity industries or relatively low as in the case of utilities. Underlying growth rates, another independent factor, may range from the business equipment industry with an annual growth rate of 14% through the electric utility industry with a growth rate of about 7% per year to the

Jan 1, 1970

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By Arthur W. Ruff

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 percent iron, 2.2 percent combined silica and alumina, and 0.05 percent phosphorous on a dry basis. Hematite is predominant and no significant sulfur or other deleterious elements are present. Figure 1 illustrates the comparative magnitude of the Carajás reserves. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air. Figures 2 and 3 show the location of Serra dos Carajás. Figure 4 shows the distribution of the major iron-ore deposits.

Jan 1, 1973

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources' South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By C. Geier

Previous mine incidents show weaknesses in mine rescue preparedness from poor training in decision making, leadership and incident command center (ICC) protocols. Computer simulations offer a larger range of training opportunities for mine rescue teams focusing on exploration and communications. The mine rescue simulator developed by the Colorado School of Mines and Rite Solutions Inc. utilizes four computers for the instructor and team, with the instructor monitoring the team?s progress. As the team explores, it relays information back to the Fresh Air Base, which then reports to the ICC. This forces a three-step communication procedure, enhancing the team?s overall communication skills and developing ICC protocols. The simulator is decision-based, demanding team decisions be made quickly. Upon completion, teams commented positively. Generally, participants said that the simulator is useful for learning how to communicate and make decisions during mine rescue emergencies. This mine rescue simulator improves team training, providing effective communications practice with an easy setup and no production interruption.

Feb 1, 2014

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By Erik Marsh, Frederick C. Harris Jr., Javad Sattarvand, Joshua Dahl, Alireza Kamran Pishhesari

Based on the mine safety and health administration (MSHA)reports, mining truck accidents are among the significant causes of fatalities in the mining industry. The major causes of haulage accidents can be divided into non-driving and driving factors, such as truck-related sudden failures and operator performance. Numerous parameters affect trucks' safe operation, but situational awareness plays a significant role. Due to the distinct structure of mining trucks, making them efficient for mining purposes, the operator has a very limited field of view (FOV), making them prone to accidents resulting in losing lives. The cabin's position blocks the truck's right and rear sides, creating several blind points around it. Aiming to test/train the operator's awareness of the surrounding, a proximity detection system is developed through a multiplayer virtual reality (VR) application to investigate the human factor in equipment collisions. The operators were examined and monitored when asked to conduct what exactly happened in the Marigold mine truck accident without being aware of the scenario. After receiving sound, vibration, and visual alarm warnings, their reaction and performance were analyzed. The platform is developed using the Unity game engine for HTC VIVE virtual reality goggles. An Omni-direction treadmill and a motion simulator platform are utilized for the player and dump truck operators. Fifteen students were monitored when driving the dump truck receiving/not receiving proximity detection alarms. None of them repeated the accident when receiving proximity alarms. Also, they found the visual alarm the most comfortable while driving the truck.

Jun 25, 2023

By Roland Hoet, Jim Patilla, Nick Madison

Increasing conveyor capacity and reliability is a common goal for many underground mines. This task is especially challenging when you must work with existing structure, belt, etc. Meeting this challenge, The Pittsburgh & Midway Coal Mining Co. North River Mine switched from constant fill to actively controlled fluid couplings, realizing a capacity increase from 2,100 tons per hour (2,300 stph) to 2,550 tons per hour (2,800 stph), with improved reliability. This paper will present a case study of The Pittsburgh & Midway Coal Mining Co.'s North River Mine underground conveyor haulage system. These conveyors included the main line conveyors as well as a tension controlled tripper booster panel conveyor. Characteristics and performance of the coupling and control system will be illustrated, demonstrating the systems controllability, simplicity, and dependability.

Jan 1, 2002

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By A. R. Hollbach

This paper presents a succinct overview of the Canadian coal situation. The topics treated specifically are: the rates of growth of coal supply and demand; the relationship between the coal and electricity generation industries which form its dominant market; the unique impact of nuclear generation on coal demand in Canada; and finally, a view of the developing technologies which will create opportunities for growth in the coal industry of the future. Resources The most important element of coal supply is the resource. The disposition of Canada's coal resources has a marked effect on their utilization, since industry in Canada has not generally developed around coal-fields. The distance from the major industrial centres of Ontario and Quebec to the major region of coal supply in Alberta and British Columbia has crested an economic barrier to the expansion of the use of domestic coal.

Jan 1, 1985

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By Bert C. Morrison

In 1961. American Smelting and Refining Company was conducting exploration for lead in southeastern Missouri using several geophysical methods. Electrical methods were used in almost every hole drilled during this period. These methods met with only limited success, with one exception. This paper deals with that exception: An Electrical Potential Method used at a single hole to indicate direction to better mineralization. This method was notably successful in the program.

Jan 1, 1970