Search Documents

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By Henry N. McCarl, Gary Waters, William A. Vogely

INTRODUCTION In the past three decades, world trade has grown from less than $100 billion per year in the years following World War 11 to slightly more than $300 billion in 1970 and over $2,000 billion in the early 1980s. Adjusted for inflation, the real growth of world trade in 1972 dollars increased from less than $175 billion per year in the early 1950s to slightly more than $342 billion in 1970 and almost $700 billion per year by the early 1980s. Thus trade as a whole has increased a little more than twofold in real terms in the past decade." Mineral commodities constituted approximately 20% of the value of total world trade in 1970, and significantly more than that proportion in terms of physical volume. By 1980, de- spite rapidly rising petroleum prices, mineral commodities accounted for roughly 18% of the total value of world trade. Crude oil alone ac- counted for about 16%, making it the single most important commodity in international trade. The worldwide recession of 198 1- 1983 brought a dramatic decline in both volume and price of crude oil, shrinking the impact of mineral commodities to roughly 10% of the value of total exports, worldwide, in 1982- 1983. The decline of mineral commodities as a pro- portion of the value of world trade in the decade 1970- 1980 is due largely to the increasing importance of manufactured goods and consumer products such as automobiles and electronic items. During this period, mineral commodity trade expanded roughly sixfold in terms of current dollars to an estimated $350 to 360 billion in 1980. This was equivalent to doubling the real value of mineral commodities in international trade in the 1970- 1980 period in constant dollars. The U.S. Bureau of Mines has expanded the traditional definition of mineral commodities to include semifinished products such as iron and steel (in addition to iron ore), refined metals such as copper, lead, zinc, aluminum, and tin, concentrates, scrap, and petroleum products. Since large quantities of essentially mineral derivatives travel in this form, it is reasonable to use these expanded definitions in stating the role of minerals in world trade. Thus minerals in world trade comprise 30 to 33% of total export trade in all commodities during the period 1976- 1980 (see Table 1.3.1). In addition, the U.S. Bureau of Mines estimates the value of all mineral commodities consumed in the world (at the national level) and compares this value to total worldwide commodity consumption. By this system, mineral commodities range from 30 to 40% of all commodities consumed each year in all countries during the period 1976- 1980 (see Table 1.3.2). The growth in export trade in mineral commodities by commodity group is shown for the period 1976-1980 in Table 1.3.3. These data parallel the swings in worldwide economic activity during the same time period. By any of the above measures, minerals, especially the fossil fuels, constitute a significant proportion of both total economic activity and

Jan 1, 1985

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Leons Kovisars

Two-thirds of the world copper produced in 1979 incurred cash costs between $0.35 and $0.89 per lb, averaging $0.62 per lb. North American costs are higher at $0.48, $0.88, and $0.68 per lb, respectively. Variable cash costs are $0.20, $0.58, and $0.39 per lb for the world; $0.29, $0.63, and $0.46 per lb for North America. Cash costs are relevant for comparing existing operations and evaluating market pricing during periods of excess supply. Analysis of full costs of production (cash costs plus income taxes, profit, and non-cash items) becomes relevant in evaluating the incentive price required to develop new production plants. In mid-1979 this cost (incentive price) was about $1.10 per lb; it is expected to approach $2.00 per lb by 1985.

Jan 1, 1979

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977

By James K. Ballard

Leach dumps in Butte are relatively new in comparison with older established dumps in other areas throughout the West. With the exception of one 10 million ton dump, all dumps have been formed on a prepared base. This is necessary because the entire leach dump area overlies an alluvial fill which varies in depth from 100 to 400 feet and through which solution would be lost. Preparation of the leach pad consists of first removing all vegetative material and compacting the exposed surface with rollers. This surface is covered with a 4" layer of minus 1" crushed rock which in turn is roller compacted. A 3" compacted layer of asphalt hot mix is then applied to the crushed rock surface. Final sealing is effected by a 1/4'? coating of catalytically applied hot asphalt. Dump leaching was inaugurated in 1964. First solution applied was wholly made up of mine water pumped to surface through a central pump shaft. Sulfuric acid was added on surface at a surge pond to control pH of the leach solution. Acid addition is necessary not only to benefit the leach dumps, but to prevent the formation of ocher scale within the pipe line distribution system. Mine water pH is on the order of 2.8. The combination of ferrous and ferric iron as well as magnesium and aluminum salts is such that ocher forms at a pH of 2.38. It is therefore mandatory to control pH at 2.0. Dump effluent pH is held at 2.3 or less.

Jan 1, 1968

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km'- (386 sq miles) in and around the Carlin Trend and own all or part of 16 out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output.

Jan 1, 1991

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979

By Frank Sames

A recently developed model is used as a tool to optimize blast designs based on the continuing combination of full scale blast assessment and performance prediction. The use of this tool has allowed to evaluate present blasting practices and proposed designs through a better under-standing of the influence of the various blast parameters. The empirical model has a modular structure covering all aspects of blast performance including 30 fragmentation, potential rock damage and 30 muckpile profile prediction. The modules are assisted by a terrain model which is compatible to most mine mapping systems, and a blast design editor. The evaluation is summarized in a blast management module. Various studies have recently been undertaken using the model to qualify and improve blast designs with respect to wall stability, optimized fragmentation and muckpile distribution, as well as to the control of the environmental effects such as blast vibration and airblast overpressure. To verify the predictions of the modeling, full scale blast assessment techniques were used to qualify blast geometry, explosives and initiation performance, rock movement, muckpile distribution, near- and far-field vibration levels and airblast ovepressures. The model provides a tool to gain an improved understanding of blasting and blast control. The modeling results are presented in a visual form which allows simple comparisons of proposed blast designs. Additionally, the model can be used for detailed analysis and blast management.

Jan 1, 1996

By William G. Holroyd

In January 1992, the Office of the US Trade Representative announced that the People's Republic of China had agreed to protect US intellectual property, including computer software, sound recordings, agrichemicals and pharmaceuticals. Under the agreement, China will make significant improvements in its patent, copyright and trade-secret laws. Ambassador Carla A. Hills, the US trade representative, said "this agreement should create significant opportunities for US firms interested in marketing high valued-added products to China." Principal beneficiaries will include the agrichemical and computer industries, as well as pharmaceutical, entertainment. The agreement will safeguard these industries' intellectual property, stimulating new exports to China and helping to generate additional growth in the US. Refractory grade bauxite was included in the mineral category of the $1.5 billion of Chinese products on which the US government threatened to impose an immediate 100% trade tariff. Refractory bauxite is available from Guyana and Brazil at higher cost and in different grades. However, refractory brick manufacturers would have had little choice but to pass on the costs to their consumers. Although the United States and China are separated by political ideology and internal governing structures, this agreement recognizes the importance of a $19 billion trading relationship. Consequently, the renewal of China's most favored-nation trading status in the US congress in -June 1992 was all but assured. Many US companies doing business in China and Hong Kong have been quietly increasing their investments since 1989. These companies can now concentrate on developing sales to the domestic Chinese market. This market is expected to surpass 1.2 billion people in 1995 and approach 1.3 billion by the end of the century.

Jan 1, 1993

By Robert Moore Lewis

A unit for separating minerals into two prescribed size fractions, designated as a Lewis Hydrosizer, was developed at the North Carolina State University Minerals Research Laboratory. Ore samples with different mineral compositions, including coal, were separated effectively with the laboratory continuous unit. Commercial size units are in operation in North Carolina and Mexico, and under construction in Norway. Additional units are being build or are in the planning stage at several companies.

Jan 1, 1983

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By P. J. Ryan

Phelps Dodge’s Candelaria copper-gold mine is located 20 km (12miles) south of Copiapó in northern Chile’s Atacama province (Region III) (Fig. 1). The Candelaria Mine is about 800 km (500miles) north of Santiago and 75 km (47 miles) east of the Pacific Ocean. Its elevation is 600 m (1,970 ft) above sea level. The Copiapó River Valley is 6 km (4 miles) northeast of the mine site. It is the only major source of water in this arid region. The average rainfall is 14mm/a (0.5 in./year). During 1995, the mine produced 521.4 kt (574,800 st) of copper concentrate containing 150 kt (165,000 st) of salable copper and 3 t (98,800 oz) of gold. The 1995 unit cash cost was less than 50 cents/lb of copper. This makes Candelaria one the world’s lowest cost copper producers.

Jan 1, 1996