Search Documents

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By Y. Yu

Florida phosphates ore typically processed by reverse flotation with an intermediate acid-scrubbing step. A single-reagent flotation process, using fatty acids or amines as the collector, would eliminate the intermediate scrubbing step plus an additional flotation step. This would not only simplify the process flowsheet but would also result in reduced reagent costs. The potential of single-reagent flotation of Florida phosphates using fatty acids as the collector is examined in this study. Introduction The beneficiation scheme now used for Florida phosphates involves the following three steps (Smith, 1976: Lawyer et al.. 1978, 1984: Moudgil et al, 1976, 1979, 1986, 1987): •rougher flotation of fluorapatitc particles using a fatty acid-fuel oil mixture as the collector. •scrubbing of fatty acid, and •cleaner flotation of silica particles using amine collector. Several attempts have been made to simplify the process flowsheet by floating either apatite or silica (not both, as is the current practice). However, single-reagent flotation schemes have had limitations in meting the concentrate-grade requirements of the phosphoric acid plants. In this study, an attempt was made to use a minimal amount of the fatty acid-fuel oil collector to obtain an acceptable grade (rougher) concentrate. Invariably, the recovery in such cases is expected to be lower than in the conventional rougher-flotation step. Therefore, scavenger flotation of tailings with additional fatty-acid collector was conducted to improve the phosphate recoveries.

Jan 1, 1997

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By Tim Neil, O&apos

Acid rain legislation, the new tax package, excess coal capacity, the effects of low oil prices, how to increase coal exports: These were among the items discussed at the May 4-7, American Mining Congress coal convention in Pittsburgh. Some 2000 people attended the convention, which also offered 15 technical sessions. As always, the state of the domestic coal industry might be characterized as "long-term promise, short-term problems." And one of these problems is acid rain. Acid rain The proposed acid rain legislation in Congress could be the most costly piece of environmental legislation ever written. In its present form, the measure could cost the nation up to $110 billion over the next 15 years. Rep. Henry Waxman's (D-CA) bill, HR 4567, would mandate large reductions in sulfur dioxide emissions from coal-fired power plants. The bill has more than 150 Republican and Democratic cosponsors. Ed Addison is president of the Southern Co., one of the nation's largest utilities and users of domestic coal. Addison noted that America's electric utility industry buys and uses nearly 85% of the coal consumed in this country. He said Waxman's bill would drive up prices of low-sulfur coal, raise electric rates, and force miners out of work in high-sulfur coal regions. In repeating a standard coal industry response, Addison said the Clean Air Act is doing the job. In recent years, while coal use has gone up, S02 emissions have gone down. Current air pollution standards are producing cleaner air, he said. Despite concern over HR 4567, the bill's future is uncertain. Several coal industry executives and analysts predict the bill will die under weight of opposition from coal, utility, and steel interests. But the acid rain issue is gaining momentum. Future legislation of some kind is likely. Meanwhile, research continues to develop clean coal technology to deal with the S02 problem. Commercialization of these front-end technologies currently lags public sentiment for acid rain legislation. Ground water runoff and contamination is another area where future legislation would seem likely. Already, one bill has been introduced in Congress. A second is being drafted. The impact of such legislation may be significant according to Bruce Leavitt, a hydrogeologist with Consolidation Coal Co. He said if current proposals are adopted, there will be more federal, state, and local government involvement in ground water regulation. In any event, the coal industry can expect to see more emphasis on preventing acid mine drainage and on water replacement, according to Leavitt. He urged those in the coal industry to present information about mining and ground water. That is needed to prevent misdirected state and federal programs, he said. Another coal industry concern is excess capacity. The industry has the mines, equipment, and employees to produce 15% more coal than at present. Problem is, the markets are not there. Slower-than-predicted growth in electric utility coal use has kept sales sluggish. There are also tax uncertainties. Congress is considering repeal of the investment tax credit and elimination of black lung payments and excise taxes as deductible expenses. One analyst estimates the coal industry would lose $1.1 billion in five years, if the changes are approved. In addition, there are the usual concerns about excessive governmental regulations involving safety and environmental matters. Bill Kegel, for example, said these regulations mean extra costs and delays in developing mines. Kegel is president and chief executive officer of the Rochester & Pittsburgh Coal Co. More than half the electrical power in the US is generated by coal-fired plants. That percentage could slip by a couple of points as nuclear generators come on-line the next few years. About 1990, though, we will see the end of US nuclear plant construction. No new nuclear plants have been scheduled since 1978. So any growth in electric power use should benefit the coal industry. BethEnergy - High Power Mountain During 1985, BethEnergy - a Bethlehem Steel Corp. - subsidiary developed High Power Mountain, a 1.8-Mt/a (2-million-stpy) surface mine in West Virginia. Construction saw movement of more than 3 hm3 (4 million cu yds) of earth. A computerized 544 t/h (600 stph) heavy media cyclone prep plant and a 3.6-kt/h (4000-stph) railroad loadout facility were built in six months. And a 5.6-km (3.5-mile) railroad spur and loop bridging a major highway were constructed. Larry Willison of BethEnergy noted the project's ambitious construction schedule. It was forced by the need for the project to be market driven and - lacking available capital - externally financed. BethEnergy did several things before obtaining with Detroit Edison a market for 0.9 Mt/a (1 million stpy) of coal. Willison said his company prospected and proved the eastern half of its 8-km2

Jan 7, 1986

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By D. B. Buddecke

Powell Bend Mine, located in Bastrop County, Texas, is owned by the Lower Colorado River Authority (LCRA). The mine is operated under contract by the Powell Bend Mining Company (PBHC), an affiliate of Pittsburg and Midway Coal Mining Co., and produces 210,000 tons of 6500 BTU/LB lignite per year for LCRA's Fayette Power Project near La Grange, Texas. PBHC operates the surface strip mine one shift per day, five days per week with a total of nine employees; six operations/maintenance and three office/supervision. The mine's productivity in 1988 averaged 100.3 tons per manshift using an l8-cubic yard dragline to uncover the lignite. Delivered cost to LCRA, F.O.B. mine, is $6.11 per ton, which includes water control and final reclamation.

Jan 1, 1990

By Dmitriy A. Malovichko

The general theory for the description of seismic sources is briefly discussed. The effect of excavations on seismic radiation is considered. Expressions for seismic source mechanisms in terms of the geometrical and mechanical parameters of source processes are provided for the following cases: fault slip and shear failure in a confined environment, dynamic stress fracturing around a tunnel, rock fall, landslide and sudden subsidence. A classification of seismic events in mines based on source mechanisms is introduced. The classification separates blast-, slip- and crush-type events. Various approaches of analysis of source mechanisms involving forward modelling and inversion are discussed. The following examples demonstrating the utility of source mechanisms in mining are presented: forensic analysis of damaging seismic events, assessment of the increase in the depth of failure for dynamic stress fracturing around tunnels and its duration, examination of the rockmass deformation regime, assessment of deformation around tunnels using crush-type events, identification and parameterisation of weak geological structures, stress inversion from slip-type events. Finally, the requirements for seismic data to ensure high quality source mechanism solutions are briefly reviewed and future challenges in the interpretation and utilisation of seismic source mechanisms in mines are speculated on.

Apr 26, 2022

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By R. G. Benson

The San Luis deposit of Costilla county, Colorado contained 11,021,000 tonnes (12,149,000 tons) of ore at 1.4 g/t (0.040 oz/st) gold in two minable zones. Gold mineralization is associated with silicification and quartz-sericite-pyrite alteration localized in breccias along a low-angle detachment fault zone in Precambrian gneiss. Gangue minerals include chlorite, specular hematite, chalcopyrite, chalcocite, and fluorite. Mineralization is mid-Tertiary in age and has a direct genetic relation to the emplacement of felsic intrusions. Portions of the ore body are unconformably overlain by sedimentary rocks of the Tertiary Santa Fe Formation. The deposit formed during the early stages of extensional tectonism along the eastern edge of the present day Rio Grande rift.

Jan 1, 1994

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By B. V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has became clearly understood am properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered.

Jan 1, 1989

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960's. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By William D. Cassity, Batric Pesic

Introduction Gold mining on an industrial scale is becoming increasingly dependent on low-grade refractory sulfide ores that contain large amounts of pyrite (FeS2) and arsenopyrite (FeAsS). Gold is usually present as sub-microscopic particles dispersed evenly throughout the sulfide matrix. Without some form of preoxidation, efficient recovery of this finely disseminated gold through cyanide leaching is hampered because the surface of the sulfide particle becomes passivated and impervious to penetration of the cyanide. Traditional methods for recovery of refractory gold from arsenopyrite ores include roasting and autoclave leaching. A modem alternative method is to preoxidize the mineral using the bacterium Thiobacillus ferrooxidans prior to attempting to re- cover the gold through cyanidation. The bioleaching of arsenopyrite ores presents a problem in the mobilization of large quantities of arsenic, present both in the +5 and +3 ionic states. Dissolved arsenic species pose a dual problem: they are -1 to the bioleaching process itself through inhibition of bacterial activity, and they also pose an environmental threat. The arsenate anion (AsO2) has been shown to be more toxic to living organisms, including Thiobacillus ferrooxidans, than the arsenate anion (AsO43) (Collinet and Morin, 1989). There is some disagreement as to the fate of arsenite in bioleaching solution. Mandl, Matulova, and Docekalova (1992) reported that dissolved arsenite concentration was constant during a long-term bioleaching study of chalcopyrite using Thiobacillus ferrooxidans. Torma and Oolman (1992) report that Thiobacillus ferrooxidans has been found capable of oxidizing As3+ to As5+. The solid products of arsenopyrite/pyrite bioleaching include jarosite (MFe3(SO4)2(OH)6 where M can be K+, Na+, NH4+ or H3O+), scorodite (FeAsO4.2H2O), ferric hydroxides, and ferric hydroxysufites (Carlson et. al., 1992; Van Breemen, 1982; Lazaroff et. al., 1982). The particular species formed is a function mainly of pH. Little study has been performed on the effect of solid products on bioleaching. Pesic and Kim (1993) showed that Thiobacillus ferrooridans cells served as a nucleation sites for jarosite particles, which grew rapidly and eventually killed the cell. Most bioleaching studies are performed at low pH&apos;s (<2.0) under uncontrolled conditions. By studying bioleaching of arsenopyrite under controlled pH conditions and at higher pH&apos;s (2.0 to 3.0), the distribution of iron and arsenic between the solid and liquid phases can be controlled, and their effects studied. The objective is to develop a bioleaching process that operates at high efficiency while keeping amounts of dissolved heavy metals low. Pesic, Stohok, and Torma (1993) demonstrated the usefulness of this approach in the leaching of cobaltite (CoAsS) concentrates. Materials and Methods The focus of this study was the bioleaching of arsenopyrite ore by Thiobacillus ferrooxidans. The parameters studied included the effects of pH, and the effects of arsenate (AsO43 and arsenite (AsO2). pH studies included pH set initially but not controlled, and pH controlled continuously with NaOH or LiOH. Bioleaching results from two strains of Thiobacillus ferrooxidans with different adaptation histories were compared. Bioleaching experiments were conducted in 150 ml stirred glass reactors using a strain of Thiobacillus ferrooxidans adapted to arsenopyrite ore, supplied by the U.S. Bureau of Mines. These bioreactors were innoculated with stock cells grown on arsenopyrite ore for 14-16 days. Typical elemental breakdown for this ore was: As, 9.90%; Fe, 18.60%, Stot, 9.26%; Suifide, 7.50%; SiO2, 25.90%. Mineralogically, the ore contained both arsenopyrite and pyrite. Bioleaching efficiency was measured by withdrawing bioleach solution samples at selected intervals, filtering, and measuring the amount of dissolved cobalt, iron, and arsenic by atomic absorption spectroscopy. Because the precipitation of iron and arsenic at higher pH&apos;s would lead to unreliable results, a 100 mg tracer of cobaltite concentrate from the Blackbird mine in southern Idaho was added to solution. Dissolution of the cobaltite tracer was used to indicate bioleaching of the bulk arsenopyrite ore. Cobalt has been shown to be stable in solution even when iron and arsenic were precipitated (Pesic, Storhok, and Tonna, 1993). The pa-

Jan 1, 1995

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April &apos;73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January &apos;77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD&apos;s experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978