Search Documents

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014

By Lana Alagha, Keitumetse Cathrine Monyake

The abstract discusses the synthesis and investigation of polyacrylamide functionalized chitosan polymers (CS-PAMs) as selective depressants for pyrite in the flotation of galena and chalcopyrite from complex sulfide ore. The study employed response surface methodology (RSM) to model and optimize the flotation process, varying parameters like the degree of deacetylation of chitosan, weight ratio of chitosan to acrylamide, and CS-PAM dosage. The developed RSM models effectively predicted iron and lead grades and recoveries, while optimization showed optimal pyrite separation from galena and chalcopyrite using CS-PAM synthesized from chitosan with a high degree of deacetylation and a specific chitosan:acrylamide weight ratio.

Apr 9, 2022

By E. F. Nelson

The 1970s have witnessed the completion and successful start-up of several new non-ferrous metallurgical operations in the Western Hemisphere which utilize large semi-autogenous mills in the grinding circuits. These facilities' are arranged either as single-stage circuits, or in a two-stage configuration n with ball mills. Another major concentrator, designed with an autogenous mill, ball mill, crusher (ABC circuit), is presently under construction and scheduled for start-up late this year. The large primary mills employed in these circuits have high diameter-to-length ratios and are designed to accept a very coarse feed, i.e., the product of a primary gyratory crusher, or run-of-mine ore. This characteristic obviates the need for a secondary-tertiary crushing plant or, in selected cases, even a primary crusher, which is a basic requirement in feed preparation for conventional grinding mills. This paper discusses three such grinding circuits and, presents operating data for two of them: the Island Copper Mine of Utah Mines, Ltd., near Port Hardy, British-Columbia,- and the Pueblo Viejo Cyanide Leach Plant of Rosario' Dominicana, S.A. on the island of Hispaniola. The design criteria for the Cyprus Bagdad Concentrator under construction' at Bagdad, Arizona, are also included. Data pertinent to these circuits are tabulated in the Summary.

Jan 1, 1977

By A. L. Holmes

This presentation in the open pit session deals with the development of a phosphate rock strip mine by CF Industries, Inc., a company that does not presently mine in the Central Florida Phosphate District. Land acquisition, engineering, financing and environmental permitting activities were begun in early 1975; site preparation, environmental monitoring and dragline construction began in mid-1975. The operation is due on-stream in late 1978. The reserve acquisition, permitting, and financing could each easily be developed into a separate paper of interest. Each, however, has been covered before for other mining ventures with similar capital and environment requirements. For that reason, I have chosen to discuss what CF Industries, Inc. is, why it is entering this new sec-tor of the agricultural chemicals business, and, to keep at least some technical basis, what design modifications are possible when the total mine output is used captively and it is unnecessary to have the flexibility to meet the numerous transportation and customer specification considerations. In an attempt to show the size and complexity of the CF organization, a brief description of existing facilities should help show why the big interest in mining phosphate rock.

Jan 1, 1977

By A. D. Rovig

Metallurgical evaluation of autogenous grinding of Anaconda's Berkeley Pit ores indicated that tonnage throughput increases, at a finer flotation feed size, were possible by converting autogenaus mills to steel ball mills. In addition, initial test work showed that the improved grind resulted in slight recovery gains in subsequent flotation processing.

Jan 1, 1974

By A. E. Isaacson

The U.S. Bureau of Mines is investigating a systems approach to metals recovery from leach liquors produced by in situ leach mining techniques. A successful in situ leaching process requires a thorough under-standing of the complex interrelationships that exist between leaching chemistry and metals recovery. Laboratory research is addressing these interrelationships in the solution mining of a copper oxide deposit. Laboratory tests have been conducted to gather baseline data related to the design and operation of continuous leaching-solvent extraction-electrowinning circuits. This paper addresses the findings of the baseline studies. Specific results include the characterization of simulated in situ leach liquors produced by leaching chrysocolla and chrysocolla-atacamite-bearing copper ores. Metal recovery procedures, utilizing four commercial solvent extraction reagents, are also characterized, and potentially troublesome leach liquor contaminants that may complicate waste management procedures are identified.

Jan 1, 1990

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By David Burgess

The paper describes experiments at the Somerset Mine, Colorado, under a cooperative agreement between U.S. Steel and the U.S. Bureau of Mines. A test was made of the tube bundle method of mine air sampling which was developed for European longwall mines; some 300,000 running feet of tubing provided continuous monitoring at 39 locations. Carbon monoxide concentrations were obtained with standard deviations of less than 1 ppm and oxygen concentrations with standard deviations of less than 0.20 percent. A base level of CO index (ppm CO evolved/pct 02 removed)) was determined to be 0-20 through most of the passageways of the mine. However, in one working section where the coal was initially hot (about 180°F within a pillar) the CO index was demonstrably higher, >20 trending upward to about 60 when smoke appeared and the section was sealed. The data are discussed in terms of laboratory experiments on CO evolution from coals.

Jan 1, 1975

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By V. P. Mehrotra

The effect of dissolved ions present in plant water on the flotation of phosphate ore from central Florida was investigated. Of the three most abundant ions, namely Ca++, Mg++ and SO4--, calcium ions were the most detrimental in the flotation of phosphate with sodium oleate collector. In one feed, a 10 ppm concentration of Ca++ ions reduced the BPL recovery from 86% to 46% whereas in the other a 40 ppm concentration lowered the recovery from 90% to 52%. The effect of Na2C03, NaHC03, Zeolite and EDTA to remove ca++ ions from water and hence improve apatite flotation was also studied.

Jan 1, 1986

By JIAQI JIN, Joe Milbourne, Maoming Fan

Gold is very important to support the financial system, and to be used in industries of the jewelry, high-tech fields such as electronics and aerospace, etc. Gold is mainly extracted from three types of ores: primary ore (vein gold), placer (alluvial gold) and associated ore. Cyanide was widely used in gold ore flotation to depress gangue minerals and leaching/cyanidation. The process of extracting gold from gold ore, its separation and flotation concentrate, specifically through a technique called cyanidation or cyanide leaching. This method, which has been dominant since the 1970s, utilizes a dilute solution of cyanide to dissolve gold from the ore. While effective, the use of cyanide raises environmental and safety concerns due to its high toxicity. Cyanide spills can have severe environmental consequences. This has led to the exploration of alternative, environmentally friendly reagents. This paper discusses processing results using the alternative flotation depressants such as sodium sulfite (Na2SO3), etc. to produce a goldrich flotation concentrate for sale to a smelter or as feed to an alternative leaching agent. and methods to extract gold from ore without relying on cyanide.

Feb 22, 2026

By H. Zhao, R. Liao, W. Qin

Theoretically, controlling redox potential to a relatively low value and inhibiting jarosite formation on the chalcopyrite surface would be an effective strategy to accelerate the bioleaching of chalcopyrite. In this work, using limonite as seed crystals, the effects of the goethite precipitation process on the bioleaching of chalcopyrite were studied for the first time. The bioleaching results showed that the addition of limonite controlled the redox potential in an appropriate range and promoted chalcopyrite dissolution through the removal of ferric (Fe3+) ions. X-ray diffraction and scanning electron microscope analyses indicate that limonite significantly induced the goethite precipitation process and inhibited the production of jarosite. We conclude that promoting the goethite precipitation process with limonite is an effective strategy in accelerating the bioleaching process of chalcopyrite.

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By J. Weyer

"A lot of incorrect, dangerous and misleading statements about the effect of CO2 on the human body can still be found in the internet, the media and in books. It is a fact that already low concentrations can lead to critical reactions, higher concentrations cause a narcosis. The real effect is not a lack of oxygen but an inner suffocation. The breathing reflex is decreased and the transport of oxygen in the blood is reduced due to a low pH value of the blood. Furthermore a reduced oxygen content in the air can also lead to the failure of diesel engines. MOTIVE Different gases can appear in active mines as well in abandoned mines, adits and caves. The most dangerous gases are CO, NO/NO2, H2S, SO2, CH4 and CO2. Although the general danger arising from these gases is mostly known some aspects are underestimated. Furthermore misleading or wrong statements exist about the detection and the effect of gases on the human body. This is especially true for CO2. In the last years a couple of accidents happened with a great number of injured persons and unfortunately also some fatalities. As a result wrong information and comments about the effect of CO2 have been published in the media. A huge unexpected CO2 outburst in a potash mine showed again some additional problems and limits for rescue troops. ORIGIN OF CO2 AND MISLEADING STATEMENTS ABOUT THE EFFECT ON THE HUMAN BODYCarbon dioxide can appear as free gas in the earth crust. It is especially known in significant concentrations in some potash deposits, in hard coal mines and some caves. Furthermore it can be formed due to complete oxidation of carbon. It can appear in technical processes. It is also used for or in technical processes, as fire extinguishing agent, as cooling agent, it is contained (added) in sparkling water or other soft drinks and it is formed by fermentation processes. Up to today a lot of wrong information about the effect of CO2 on the human body is published or is still in the mind of many people and unfortunately even in the mind of members or leaders of rescue troops. On August 16th 2008 a faulty CO2 extinguishing installation in the city of Mönchengladbach/Germany caused the injury of 107 people and the evacuation of further 150 people /1/. People on the streets became unconsciousness and felt down. Fortunately all could be rescued due to the immediate rescue operation of local fire fighters. Furthermore the CO2 concentration on the ground was diminished by help of a helicopter. What could have happen with the engine will be discussed later. After 6 days a second similar accident took place /2/. In the news members of the rescue teams explained that CO2 leads to suffocation due to a lack of oxygen. This is wrong! Also cave explorers often say that a burning candle can detect a low oxygen and/or high Carbon dioxide content in the air. This is also wrong and deadly dangerous! Similar statements we find nowadays in the internet /3, 4 and many other/. In a forum “science and mathematics > chemistry” several people say that winegrowers go with a candle into the vine-cellar to detect CO2 /5/. Again: this can be deadly! Another dangerous statement is that CO2 in higher concentrations leads to headaches so people should leave such areas. A last example found in the literature is that at 3 % the breathing volume is doubled and at a concentration of 20 % one can felt some warmth on the skin. Both is not wrong but can lead to false conclusions. /6/"

Jan 1, 2015

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By R. B. Elver

The level of steel consumption per capita is one of the principal indicators of a country's standard of living. It is no coincidence that the materially advanced nations possess viable iron and steel industries to provide a reliable and economic source of steal for the manufacturing industries. No other metal is as dominantly important in manufacturing as steel. The blast furnace - steel furnace complex based on coking coal, ferrous scrap and iron ore - continues to be the principal steel-producing method. Less important is the electric furnace method based on scrap, In recent years, there has been considerable interest in the many direct reduction processes that are not dependent on coking coal but usually produce a product for further refining in steel furnaces. No matter which series of processes are used, iron ore is essentially the only source of virgin iron units. Thus, to such a vital and capital-intense industry as steel, access to a relatively inexpensive, long- term supply of iron ore is essential.

Jan 1, 1964