Search Documents

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company's first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore' in March 1982. The mill's present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

By S. Acar

"In recent years the gold mining industry has been challenged by declining metal prices as well as having to treat ores that have low grades and are refractory in nature. Many factors must be considered when metallurgical studies are designed to develop process design criteria for these type of ores. These factors are mostly related to the mineralogical and chemical compositions of the ores, the geological setting of the deposit and how the ore/waste will be mined, such as whether openpit or underground, the mine schedule, and the mine fleet type and capacity. The purpose of this paper is to provide an experience-based practical approach to how to select and characterize test samples as well as devise process development metallurgical studies for both oxide and refractory gold ores, and to provide insight into some of the matters that might go wrong during the course of the studies. This paper is intended as both a guide for someone new to the field and also as a reminder for those familiar with the field. IntroductionThe recent decline in ore grades and metal prices have challenged mining companies to reduce capital and operating costs associated with developing new mineral resources. In some cases, metallurgical studies have been sacrificed to prevent cost overruns resulting in inadequate mineralogical, chemical and metallurgical characterization. Consequences have included longer construction schedules, higher initial and working capital, higher operating costs and less than desirable plant performance (Whincup, 2010; Torres, Chaves and Meech, 1999).Mineralogy, geology, mining type and sequence, and the metallurgy of an orebody will determine the process development metallurgical study requirements and eventual process plant design. Therefore, once the geologist has an early indication of a prospective orebody, geologists, metallurgists, mining engineers, and social and environmental responsibility scientists should convene and devise a plan on how to exploit the orebody economically (Lunt, Ritchie and Fleay, 1997).Geologists may find a prospective orebody solely based on grade. However, if the orebody cannot be mined and processed economically, then it is deemed not to be a deposit. An example of this could be a refractory gold deposit, either sulfidic, carbonaceous or siliceous refractory or any combination of those, that may not be mined and processed economically due to reasons such as the physical location of the deposit, depth of the ore lode, or social and environmental concerns. Therefore, an early collaboration between all disciplines must be established.Each orebody may have its own unique mineralogical, geological and chemical characteristics (Guresin et al., 2012). These unique characteristics should be effectively sampled to reduce risks associated with process design and engineering efforts for the process development metallurgical studies. If the sample or samples are not representative of these unique characteristics, then the studies performed will be pointless. The project metallurgist in charge of conducting metallurgical studies should also possess general geology, mineralogy and mine engineering knowledge. Recommended readings are a book on understanding mineral deposits by Misra (2000) and articles on heap leach development by Scheffel (2014a and 2014b)."

Jan 1, 2016

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By R. J. Pugh

In addition to directly analyzing the surfaces of minerals using high vacuum instrumentation methods, some important surface properties of mineral fillers can be determined indirectly by using reactive chemical probe molecules. This technique enables the strength and the number of the surface reactive sites to evaluation and this type of information is useful in predicting interfacial behaviour of minerals. One method of classifying these surface sites is by using Lewis acid/base theory and this type of approach could enable one to predict the adsorption of functional groups in dispersants, thickeners, pigments, etc. Also the adhesion of polymer matrices to the filler surface may be improved.

Jan 1, 1992

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

By Gilbert C. Robinson

Manufacturers of brick and tile are showing growing interest in the possibility of manufacture of a clay bonded block. The block would have the shape of concrete block, but would be made without the use of Portland cement, Instead, the block would be made&apos; from mixtures&apos; of an aggregate and the present raw materials of the brick industry. The finished units would weigh 20 to 30 pounds and meet the specifications for Grade A concrete block. The present status of the clay block development shows one manufacturer actually in production of these units$, two additional manufacturers are attempting production and many manufacturers are actively engaged in development work. At least four major research laboratories are engaged in the development program. There are several different processes available for clay block production. These processes differ primarily in the type of aggregate used or in the type of forming operation selected. I would like summarize these possible methods.

Jan 1, 1960

By Pratama Mochamad Rizki, Andika Satya

High-risk area in open-pit mining should always be monitored by the operational supervisor because of its nature. One of this type is the soft soil dump area. Due to the unstable bearing capacity of the soil, it’s highly possible for us to find cracks in the area. This paper aims to build computer vision which able to detect truck’s distance from safe limit allowed during dumping activity. The system will warn the truck’s driver if the truck has crossed that predetermined safe limit.

Jun 25, 2023

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By John B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with alum. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1984

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By C. B. Clemmens

Accurately predicting ground control conditions before mining requires a comprehensive exploration approach including photogeologic mapping (satellite and low altitude), delta modeling and, particularly, geophysical logging. In situ properties, density; strength indices; grain size; clay content; and aquifer location, can be estimated with this inexpensive technique. Geophysical measurements can be spot-checked by field or laboratory tests on core samples and by hydrologic (pressure) testing. Each phase of drilling should be accompanied by refinement of the delta model, facilitated by log signatures. Measured properties can then be projected into geologically similar areas. A properly planned program will delineate both the "worst-case" and normal support conditions. Suspect areas can be avoided by mine layout and the mine plan can contain support contingencies for anticipated trouble spots.

Jan 1, 1985

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By Ma Lianren, Wang Duolun, Chenzhe Li, Hongyan Xie, Fenglan Luo, Huixin Jin

In this study, the oxidation of low-grade pyrolusite to potassium manganate in alkaline solutions under O2 pressure has been investigated. The effects of different conditions on the high-grade and low-grade pyrolusite leaching process were investigated based on thermodynamic calculation, as well as the reaction mechanisms and kinetics of the low-grade pyrolusite during the leaching process. The results showed that the manganese conversion rates of the two types of pyrolusite were almost the same, and reaching 99% for high-grade pyrolusite and 96% for low-grade pyrolusite under optimal conditions. The optimum condition for low-grade pyrolusite sample JM-2 was achieved as 0.5 MPa of the oxygen partial pressure, 55% of KOH, 14 of the initial alkali-manganese ratio, and ≤ 48 μm of the mineral granularity at 260 °C within 150 min of leaching time and 500 rpm. In alkaline leaching of low-grade pyrolusite, Mn(IV) was oxidized into Mn(VI). The particles changed from large particles to flakes and finally formed crystals. Finally, the shrinking core model was used to fully describe the leaching kinetics of the manganese. It was demonstrated that the leaching of manganese was controlled by the chemical surface reactions and the activation energy which equals 115.9121 kJ/mol.

Dec 3, 2022

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024