Search Documents

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020

By G. Zhu

Bulk and differential laboratory flotation tests have been carried out using a synthetic mixture of chalcopyrite and molybdenum ore. In addition to boiling and roasting, six different depressants are tested so that the best conditions of separation can be identified. These reagents include sodium cyanide with and without zinc sulfate, potassium ferrocyanide, sodium hydrosulfide, arsenic Noke's reagent, and sodium sulfide. The data indicate that most of these reagents are effective chalcopyrite depressants. However, sodium hydrosul fide can be used preferably if economic, operational, and environmental factors are taken into consideration.

Jan 1, 1983

By R. N. Gow

EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. However, successful application of these diagrams requires several things be kept in mind to prevent what others have termed ?gross errors? in their calculation and use. The aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the thermodynamic equilibrium software, STABCAL. This includes a breakdown of the Gibbs? Phase Rule and how it is employed in STABCAL to modify the diagrams. This methodology was then applied to the aqueous Cu-As-S system and resulting diagrams are compared against examples of those generated using the predominant-ion method. The resulting mass-balanced diagram for enargite (Cu3AsS4) is noted to compare well with spectroelectrochemical measurements using Raman spectroscopy and cyclic voltammetry.

Feb 23, 2014

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"Una de las enfermedades más extendidas en la industria minera es la pérdida de audición inducida por el ruido. La exposición de los mineros a niveles de ruido superiores a los niveles de exposición permisibles resulta en la pérdida de audición de aproximadamente el 80% de los mineros del carbón a la edad de jubilarse. En este contexto, el Instituto Nacional para la Seguridad y Salud Ocupacional (NIOSH, por sus siglas en inglés) está realizando investigaciones para desarrollar controles de ruido aplicados a los sistemas de minado de tajeos largos. Este método de minado es usado para extraer la mitad de la producción nacional de carbón subterránea. A partir de las mediciones en campo, se determinó en investigaciones anteriores que los componentes dominantes que generan sonido en el cizallador de un sistema de tajeos largos son los dos tambores de corte utilizados para extraer el carbón. Debido a las dimensiones y complejidad de los sistemas de minado de tajeos largos, el proyecto NIOSH desarrolló un modelo de elementos finitos validado del tambor de corte para utilizarlo en la predicción del sonido generado por este debido a las fuerzas de excitación experimentadas en las operaciones subterráneas. Este mismo modelo se utilizará para desarrollar controles de ingeniería para el ruido del tambor. Las fuerzas de excitación surgen de la interacción de la broca de corte y el carbón, y se transmiten al tambor de corte a través de los sujetadores de brocas. Debido a las condiciones adversas en el frente y la falta de instrumentación aprobada para uso subterráneo, las fuerzas operativas de corte de carbón no han sido evaluadas anteriormente. Para este fin, NIOSH, en colaboración con la Universidad Tecnológica de Michigan, desarrolló una broca instrumentada autónoma con seguridad intrínseca para medir estas fuerzas. Este artículo describe el desarrollo de la broca instrumentada y la medición de las fuerzas operativas de corte de carbón en tres minas. Las mediciones revelaron que las fuerzas tienen un espectro plano, algo característico de la naturaleza del impacto de estas fuerzas, hasta alrededor de 100 Hz. Por encima de esta frecuencia "cutoff", la magnitud de la fuerza disminuye a una razón proporcional al cuadrado de la inversa de la frecuencia."

Jan 1, 2014

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By Raúl Castro, René Gómez

In underground mining, rock fragment size is a key variable for productivity because it impacts equipment selection and mining structure design. This study characterizes granular material fragmentation during its flow to understand its characteristics and mechanisms. Tests were conducted using a laboratory setup to emulate various heights where material is drawn. The fragment-size distribution was measured before and after tests for clay, concrete fragments, and gravel. Results showed that fragmentation mainly occurs in minor sizes, with significant increases in fine material as travel distance increases.

Jan 10, 2022

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The use of phosphorus by mankind is long established. From use in agriculture, foods, high tech electronics, and more recently in EV battery cathode production, one cannot escape its impact on today’s society. This paper will review and describe the circular journey of phosphorus through its value chain from the mining operation of phosphate ore through beneficiation into downstream chemicals production and finally into the EV battery cathode production space. This will include a review of phosphoric acid production from phosphate concentrate using wet process route and thermal route. The wet process route discussed will be via dissolution of phosphate concentrate by sulphuric acid. The thermal route will discuss thermal decomposition of phosphate concentrate using submerged arc furnace to produce yellow phosphorus followed by its combustion to produce phosphorus pentoxide and subsequent hydration to produce phosphoric acid. It will also discuss briefly other phosphate derivatives for specialty chemicals and recovery of phosphorus units from wastewater treatment plants, sewage sludge and incinerator ash. Finally, the paper will discuss the use of phosphorus in EV batteries in the form LFP cathode materials and its production. It will also briefly discuss the LFP battery recycle.

Sep 11, 2023

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Chee Theng

"Mineral processors know you can put in the best technology in the world but it won’t work optimally without the support of the operators. Conversely, you may have complete operator support but won’t get top results without the right technology. When the two come together, the returns can be phenomenal.The first day of talks at the 68th Annual Colorado MPD Conference, held April 26-28 at The Broadmoor in Colorado Springs, covered the ground on these industry wisdoms.Coming together as a team“Think of the people, not just the lab and the numbers. That makes all the difference,” said Dee Kippers, of FMI Henderson Mine, in her talk on “Process optimization during a market downturn (A Moly MacGyver story).” Kippers told an entertaining story of the journey she and her team took in tackling the issue of an annual spike in iron content in the product at Freeport- McMoRan’s Henderson primary molybdenum mine near Empire, CO.As the metallurgists tried one thing after another — cranking up the iron depressant, adjusting pH with sodium hydroxide and hydrated lime, modifying reagent levels — Kippers found that when she shared her results with the operators, communicated with them on what she was doing and got their input, they were more willing to work with her, and more understanding and supportive of her efforts.The results make the case for getting people on board and coming together as a team. The cost savings from their optimization efforts, with little capital investment, have been “enough to cover the annual salaries of our metallurgy department and then some,” Kippers said.Considering the environmentDavid Lemieux, of Dundee Sustainable Technologies (DST), talked next on “Cyanidefree process for gold extraction,” presenting the results obtained from a demonstration campaign of the company’s novel chlorination process for gold extraction and associated arsenic stabilization process. Developed at an investment cost of C$35 million, they are ready for commercialization, having been demonstrated on the laboratory, pilot and demonstration scales.The DST process is differentiated from the Plattner chlorination process, which was in use from 1851 to 1916, by moderate process conditions of atmospheric pressure and ambient temperature — the result of using sodium hypochlorite solution, or bleach, instead of direct injection of chlorine gas — and new, cheaper materials of construction, such as polymers, plastics, fiberreinforced plastics and Teflon, resulting in lower capital and operating expenditures."

Jan 7, 2018